CRUX RVCCH-75DC Manual

CRUX Bakkamera RVCCH-75DC

Læs gratis den danske manual til CRUX RVCCH-75DC (6 sider) i kategorien Bakkamera. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 17 anmeldelser. Har du et spørgsmål om CRUX RVCCH-75DC, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

RVCCH-75DC

Rear View Integration Interface with VIM

for DODGE RAM Trucks

INTERFACING SOLUTIONS

Sightline

Multi View Integration

Crux Interfacing Solutions • 6860 Canby Ave., Suite 104, Reseda, CA 91335

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.010319

1 of 3

• Adds reverse camera input to the Uconnect Touchscreen Radio

• Aermarket tailgate handle camera included

• Automacally switches to Rear-view when car is in Reverse mode

• Plug & Play Installaon

PRODUCT FEATURES:

PARTS INCLUDED:

RVCCH-75DC Module RVCCH-75DC Harness CDR-02 Camera

INSTALLATION DIAGRAM:

WHITE Wire

Parking Guideline

To Radio

OEM Radio

Harness

DIP

SWITCH

LED*

*LED RED = Power ON Status

LED BLUE = Data Bus ON Status

RVC Video

Signal Input

RED Wire Push in Connectors

all the way

Line up Arrows

Regulator

20 Ft. Coax Cable

RED Wire

Tape O

(Not Used)

BLACK

Wire

BLACK

(Ground)

8-Pin Molex Represents Solder Joint

Connect RCAs and secure

with tape all around

WHITE Wire

(Camera Power Output

+12V 250mA)

OR*

*Connect BLACK (ground) wire to chassis ground.

If video noise is present, we recommend connecting the

ground wire to the BLACK ground wire on the RVCCH-75DC harness.

Chassis Ground

Crux Interfacing Solutions • 6860 Canby Ave., Suite 104, Reseda, CA 91335

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.010319

2 of 3

INTERFACING SOLUTIONS

Sightline

Multi View Integration

DIP SWITCH SETTINGS:

INSTALLATION INSTRUCTIONS:

INSTALLING THE CDR-02 CAMERA AND CABLE

1. Remove the OE tailgate handle.

2. Remove the OE lock cylinder and install in the CDR-02 camera housing.

3. Install the new tailgate handle and run the cables to the radio.

4. Remove the factory radio to gain access to the factory connectors.

5. Route the wires towards the radio and make the power and video connecons. For powering up the camera, use the 12V

OUTPUT (White Wire). (See Wiring Diagram on page 1)

6. Connect the camera ground wire to chassis ground. If video noise is present, we recommend connecng a ground wire

from the camera to the BLACK wire on the RVCCH-75DC T-harness.

7. The CDR-02 has a built-in parking guide lines opon and is defaulted to ON from the factory. To turn OFF the parking guide

lines, cut the thin WHITE wire located on the camera cable 4 feet from the camera. Unplug the barrel connectors on the

cable for 10 seconds. Align the arrows on the barrel connectors and rmly plug them together.

8. Test the camera before re-installing the radio.

CODING THE RADIO FOR A REAR VIEW CAMERA

The radio has to be coded to accept a reverse camera. Please follow the coding procedure below:

1) Turn key o and remove the key from ignion.

2) Open the driver door then close it (make sure all doors, li gate and hood are also closed).

3) Look at the module and wait for LEDs to turn o then disconnect the module.

4) Before plugging back the module, turn all DIP switches to ON then OFF.

5) Set DIP switches to the sengs provided above.

6) Reconnect module and wait for the LEDs to turn o.

7) Start engine and the coding operaon is now complete.

8) Put the gear in reverse to test the camera.

DIP SWITCH FUNCTIONS:

DIP 1 = Set to OFF

DIP 2 = Rear View Camera ON / OFF

DIP 3 = Set to OFF

DIP 4 = Set to OFF

DIP 5 = Defaulted to OFF*

DIP 6 = Defaulted to ON*

RVCCH-75DC

Rear View Integration Interface with VIM

for DODGE RAM Trucks

*DIP 5 & 6

If the radio is having turn-on issues, please try the following:

Aempt 1: Set 5 & 6 to ON

Aempt 2: Set 5 to ON and 6 to OFF

Aempt 3: Set 5 to OFF and 6 to ON

1 2 3 4 5 6

Produkt Specifikationer

Mærke:	CRUX
Kategori:	Bakkamera
Model:	RVCCH-75DC

Har du brug for hjælp?

Hvis du har brug for hjælp til CRUX RVCCH-75DC stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Bakkamera CRUX Manualer

CRUX RVCAD-81T Manual

23 August 2025

CRUX RVCGM-80S Manual

23 August 2025

24 Juli 2025

29 December 2024

29 December 2024

29 December 2024

29 December 2024

CRUX RVCCH-75RC Manual

18 November 2024

CRUX RVCCH-75DC Manual

16 August 2024

CRUX RVCCH-75WTC Manual

15 August 2024

Bakkamera Manualer

Nyeste Bakkamera Manualer

EchoMaster CAM-01-N Manual

6 Oktober 2025

EchoMaster PCAM-DPLLP-N Manual

6 Oktober 2025

EchoMaster PCAM-BS1-N Manual

6 Oktober 2025

EchoMaster PCAM-JP2-N Manual

6 Oktober 2025

Dometic PerfectView RVS 545 Manual

29 August 2025

Dometic PerfectView CAM 360 Manual

29 August 2025

Dometic PerfectView RVS 729 Manual

29 August 2025

Dometic PerfectView RVS 745 Manual

29 August 2025

Dometic PerfectView RVS 535 Manual

29 August 2025

Dometic PerfectView RVS 555X Manual

29 August 2025