Draper 253219 projection screen 253219 Manual

Draper Projektionsskærm 253219 projection screen 253219

Læs gratis den danske manual til Draper 253219 projection screen 253219 (2 sider) i kategorien Projektionsskærm. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om Draper 253219 projection screen 253219, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Assembly/Mounting Instructions

Onyx Permanently Tensioned Projection Screen by Draper

Caution

① Read instructions through completely before proceeding.

② Follow instructions carefully. Installation con trary to instructions

invalidates warranty.

③ Screen should be accessible for complete removal should fabric

become damaged or should other ser vice be required.

④ Screen should be installed level (using a carpenter’s level).

⑤ Nothing should be fastened to screen frame or viewing surface.

⑥ Make sure you have received all parts (see parts list below and

exploded diagram on page 2).

⑦ Tools Required: Medium (#2) Phillips screwdriver (6" or greater shaft

length suggested). Optional tools: Flat blade screwdriver or small

putty knife.

⑧ Installer is responsible for providing appropriate hardware for mounting.

⑨ When lifting assembled screen, do not lift at only one corner; lift at

both corners. Lifting by one corner could result in damage to the

screen frame, especially on large screens.

⑩ The ideal temperature range for assembling folding screens to prevent

damaging the surface is 68°-78° F (20°-26° C). Assembling below

recommended temperatures may damage surface and void warranty.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

If you encounter any difﬁ culties installing or ser vic ing your Onyx screen, call your

dealer or Draper, Inc., Spiceland, Indiana, (765) 987-7999 or fax (765) 987-7142.

Onyx—Hardware and Parts List

Frame Preparation

① Clean area and place frame assembly pieces face down. Insert plastic

corner pieces into ends of aluminum frame extrusions as indicated in

Figures 1 through 4. Secure each corner to each frame extrusion by

threading one #10-24 fastener through hole in plastic corner and into

rounded slot in aluminum frame extrusion.

Caution: Do not over-tighten fasteners—over-tightening could cause

damage to the frame corners.

Figure 1

② Secure corner pieces to aluminum frame extrusions with four (4) remaining

fasteners. Check to verify that all four (4) plastic corners are secure to

aluminum frame extrusion lengths and all eight (8) fasteners are tight (see

Fig. 5).

Caution: Do not over-tighten fasteners—over-tightening could cause

damage to the frame corners.

Figure 2

Frame Extrusions - 4

Frame Corners - 4

#10-24 fasteners - 8

Z-Brackets - 2

Viewing Surface - 1

Plastic Tubing - 4

Surface Retention

Extrusions- 4

Front

Back

Figure 3

Figure 5

Figure 4

(Continued on Page 2)

Patented by Draper, Inc., U.S. Patent Nos. 6,785,047; 7,113,332; and 7,369,310.

Caution: When lifting assembled screen, do not lift at only one corner; lift

at both corners. Lifting by one corner could result in damage to the screen

frame, especially on large screens.

Onyx by Draper Page 2 of 2

Figure 8

Mounting Screen to Wall

① Determine height at which screen is to be mounted.

Please Note: Top edge of screen frame will be located 1.5"above mounting

bracket hole centerline when mounted to wall.

② Mark hole centerline so that both Z-brackets can be mounted parallel and

at equal height.

③ Install Z-brackets so that the outermost edges are safely within the overall

length of the aluminum frame extrusion to allow for minor horizontal screen

adjustments. Installer is responsible for providing attachment hardware.

④ Position screen slightly above Z-brackets on wall (see Fig. 10).

Surface to Frame Assembly

① Return frame onto clean surface, face down, and drape completed surface

assembly over completed frame proﬁ le with rounded edge of surface

retention extrusion visible.

② Insert any side of surface to notch #1 on corresponding side of frame

extrusion (see Fig. 8).

③ Insert opposite side of surface to notch #1 of frame extrusion.

④ Repeat steps 2-3 with remaining edges of surface.

⑤ Ensure surface retention extrusions are centered lengthwise in tension

slots on all 4 edges of surface.

⑥ If additional tension is desired or required over time, adjust surface one

edge at a time to tension notch #2.

Please Note: It is not necessary to adjust more than one edge at a time to

increase surface tension.

Z-brackets

supplied with

screen. Installer is

responsible for

ensuring appropriate

screws/bolts are used.

Wall

Figure 10

⑤ Lower screen until it engages over Z-brackets. Center screen horizontally

on brackets as necessary.

Please Note: Make sure screen is installed level.

Figure 6

Surface Preparation

① Move frame assembly out of the way, unroll viewing surface and place on

smooth/clean surface. (Orient viewing surface so that folded side of hem is

visible.)

② Insert plastic tubing inside pocket formed by hem on all 4 edges of viewing

surface (see Fig. 6).

③ slide surface retention extrusion (rounded edge visible) along Carefully

hem and onto surface on all 4 edges of fabric (see Fig. 7). Caution: Do

not allow fabric to snag on end of extrusion. If the screen

fabric is not parallel with the surface retention extrusion, then

it may slit and tear during installation.

Please Note: To make this step easier, pinch the end of the pocket closed

before sliding it into the surface retention extrusion.

Figure 7

④ Surface retention extrusion should extend beyond edge of viewing surface

equally at both ends.

⑤ Verify that all surface retention extrusions are installed with rounded edge

visible and are centered on surface material.

Plastic Tubing

Surface Retention

Extr sionu

Back of

V w uie ing S rface

Back of

V w uie ing S rface

Surface

Retention

Extr sionu

Fabric Attachment Extr sionsu

V wie ing

Surface

Onyx (Exploded Rear View)

Onyx Frame

—Side Detail*

*Viewing surface is approximately ¼" from wall.

www.draperinc.com (765) 987-799

Corner Reinforcement

① If screen is being ﬂ own (suspended), raised and lowered by a TorkStar, or if

screen is 12' (viewing area) or larger in overall height or width, install

Corner reinforcement Gussets to all four corners (see Fig. 9)

Figure 9

Produkt Specifikationer

Mærke:	Draper
Kategori:	Projektionsskærm
Model:	253219 projection screen 253219
Vægt:	29480 g
Produktfarve:	Black,White
Naturligt aspektforhold:	16:9
Synlig skærmbredde (W):	3556 mm
Synlig skærmhøjde (H):	2032 mm
Samlet skærmstørrelse (højde x bredde):	2235 x 3759 cm
Diagonal:	161 "
Format:	HDTV
Kanter:	101.6 mm