Draper 78775 Manual
Draper
Loddemaskine
78775
Læs nedenfor 📖 manual på dansk for Draper 78775 (4 sider) i kategorien Loddemaskine. Denne guide var nyttig for 4 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2.5 brugere
Side 1/4
HEAT GUN
78775
MICRO BUTANE
EN
Original Instructions
Version 2 – March 2023
1. Specication
2. HealthandSafetyWarnings
• Observe all standard safety precautions and good
practices when working with naked ames and
ammable fuels.
• Keep the work environment clear and well-lit, with
bystanders at a safe distance.
• Keep this product out of reach of children at all times.
• ALWAYS wear appropriate eye and face protection and
protective gloves when using this product.
• Check the heat gun for damaged, clogged or corroded
parts and leaks before every use.
− use the product if it is damaged or leaking DO NOT
in any way; contact Draper Tools for repair and
replacement options.
− If you suspect that the product is leaking gas, move
it to an external environment immediately.
The product can be tested for leaks by Important:
dabbing soapy water solution on joints and
connections while gas is added to or stored in the
product. Leaks will create a steady feed of soapy
bubbles at the breach point.
• Use ONLY in well-ventilated environments.
• use this product in environments where paint DO NOT
fumes, solvents and other ammable materials are
present.
• Use only good quality butane gas.
WARNING!Butanegasishighlyammable;
handle it carefully and in accordance with the
instructions on the canister.
• During rst use, allow a few minutes for the product to
settle once ignited before directing it towards the
workpiece.
WARNING! The metal parts of the heat gun
becomeveryhotduringuse.DONOTtouchthe
barrelorworkpieceuntiltheyhavecooled
thoroughly.
WARNING!Avoidcontactwithskin,clothingor
otherammablematerials.
• leave the product running while unattended.DO NOT
• expose the product to temperatures above 49°C DO NOT
(120°F) or to prolonged periods of sunlight.
• switch o the product while it is not in use and ALWAYS
ensure that the control lever remains in its lowest
position.
• After each use, ensure that the ame is fully
extinguished, the control lever is in its lowest position
and the product has completely cooled before storing.
• attempt to disassemble or modify this tool in DO NOT
any way.
• refuel outside.ALWAYS
• smoke while refuelling.NEVER
WARNING! This product is not insulated against
electricity.NEVERusethisproductonworkpieces
that are connected to electrical power.
WARNING! ALWAYS ensure that the control
leverremainsintheopositionafteruse.
Ifthefuelsupplyisre-engaged,residual
heat can cause reignition without operating
theignitionbutton.Oncethetoolhas
cooled,followthenormalignition
procedure to reignite.
Stock No. 78775
Part No. GT9
Fuel type Butane
Approx. temperature ≤ 450°C
Operating time (one gas
lling)
20 mins approx. at mid
setting
Dimensions W 90 × H 35 × Ø 20mm
Weight (80% gas ll) 51g
Read this manual in full before using this product and
retain it for future use. Always use the latest version of the
manual. Please visit drapertools.com/manuals for the
latest version of this manual.
3. Refuelling
WARNING!Beforellingtheproduct,ALWAYS
ensurethatthecontrolleverisinitslowest
position.ONLYusebutanegastofueltheproduct.
Important: This product is not shipped with butane gas
and MUST be fuelled before use.
1 Fig.
(A)
1. Turn the heat gun upside-down and push the butane
can nozzle rmly into the lling valve (A).
2. Filling begins automatically and takes only a few
seconds.
The fuel level can be viewed through the window (B)
beneath the control lever (C).
3. Allow a few minutes after lling for the gas in the
product to stabilise.
WARNING!Allowescapedgastodispersebefore
lighting the heat gun. NEVER light the product
whileagascanisterisinsertedintothelling
valve.
4. IgnitionandUse
WARNING! Keep your hands and face away from
thebarrelwhenignitingandoperatingthe
product.Griptheheatgunbythehandleonly.
1. Fuel the product and allow the gas to settle.
2. Move the control lever (C) to the ON position to start
the fuel supply.
2 Fig.
(C)
(B)
3. Depress the ignition button (D) repeatedly until the
ame is lit.
3 Fig.
(D)
4. Adjust the size and temperature of the ame using
the control lever.
5. Allow approximately 30 seconds for the ame to
reach temperature, then direct the heat gun safely
towards the workpiece.
6. Wait for the gauze (E) to glow, indicating that
operating temperature has been reached.
7. Direct the heat gun at the workpiece to heat it,
keeping your hands away from the barrel and the
vents on the side of the heat gun.
WARNING! DO NOT hold the heat gun too
closetotheworkpiece.Heatreectedback
towards the heat gun may damage the heat
gun or cause injury. NEVER allow the heat
guntotouchtheworkpiece.
8. To switch o the heat gun, move the control lever
fully to the left and allow several minutes for the
gauze to cool.
– The clear lid (E) can be used as a stand while
cooling.
9. While the gauze is still hot and glowing, the heat gun
can be reignited by moving the control lever out of
the OFF position.
4 Fig.
(E)
Produkt Specifikationer
| Mærke: | Draper |
| Kategori: | Loddemaskine |
| Model: | 78775 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Draper 78775 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Loddemaskine Draper Manualer
1 Juni 2025
31 Maj 2025
31 Maj 2025
31 Maj 2025
31 Maj 2025
Loddemaskine Manualer
- Loddemaskine Craftsman
- Loddemaskine Cocraft
- Loddemaskine Westfalia
- Loddemaskine Edsyn
- Loddemaskine Holzmann
- Loddemaskine Silverline
- Loddemaskine Velleman
- Loddemaskine Truper
- Loddemaskine Powerplus
- Loddemaskine Nedis
- Loddemaskine HQ
- Loddemaskine Yato
- Loddemaskine Hakko
- Loddemaskine CFH
- Loddemaskine Steren
Nyeste Loddemaskine Manualer
21 Januar 2025
12 Januar 2025
4 Januar 2025
4 Januar 2025
3 Januar 2025
3 Januar 2025
1 Januar 2025
1 Januar 2025
1 Januar 2025
1 Januar 2025