Draper Rolleramic 240" Manual

Draper Projektionsskærm Rolleramic 240"

Læs gratis den danske manual til Draper Rolleramic 240" (2 sider) i kategorien Projektionsskærm. Denne vejledning er vurderet som hjælpsom af 44 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 22.5 anmeldelser. Har du et spørgsmål om Draper Rolleramic 240", eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Wall Installation—

Brackets should fasten to studding or other structural supports within wall.

Suspended Installation—

Chains should be attached to solid beams or rafters above screen. If possible,

screen mounting brackets should be positioned so chains hang vertically.

Turnbuckles should be connected between chains and mounting brackets. After

screen has been suspended, turnbuckles should be adjusted so that screen hangs

level.

Recessed Installation—

Recess should be constructed to ﬁt screen case with brackets (see “Case

Dimensions” on back page). Design recess so that entire bottom of screen case

is unobstructed to permit access to bottom panel, screen roller and surface for

servicing if required.

Hanging Screen

General:

When locating viewing surface and checking clearance for screen operation,

remember surface is not centered in screen case: see dimensional drawings on

reverse. All installations should observe these important criteria:

Screen should be positively and securely supported so that vibration or even

abusive pulling on viewing surface will not weaken installation.

Installer must insure that fasteners used are of adequate strength and suitable

for the mounting surface.

Entire bottom of case must be readily accessible after installation is complete.

Be sure the access door opens freely for adjustments and service.

Installer should make sure mounting brackets are ﬂush with the sides of the

case to provide stability when hanging screen. Keep case level when lifting

and mounting.

5 Screens through 14' wide have 2 mounting brackets; wider screens have 3.

Brackets should be located along case to line up with supporting beams or

studding. Motor end bracket must be located 1"-6" to right of access door. Idler

end bracket must be located 6"-12" from right end of case. Failure to mount

brackets as directed could cause the case to bow and result in damage to screen.

Please Note: Mount the case using the two end brackets ﬁrst. If a center

bracket is provided, mount it last. The center bracket is designed to prevent

sagging of the case, and must be mounted so that it is level with the others

and does not force the screen case up.

Make sure the top of the screen case's bottom board at no point touches the

roller/viewing surface.

Do not use screen case to support adjacent sections of ceiling.

If trim pieces must be attached to case, do not permit screws to pro trude

through ¾" wall of case. Do not attach trim with nails.

If case is painted, viewing surface slot must be shielded to protect viewing

surface from paint splatters and overspray.



Do not seal unit in ceiling until electrical connections have been made and

screen has been operated successfully. Screen must always be installed level

so that fabric will not roll incorrectly or wrinkle.

These instructions are meant as a guide only. They do not imply any responsibility

on the part of Draper, Inc. for improper installation or faulty workmanship at the

jobsite.

Installation/Operating Instructions

Rolleramic Electric Projection Screen by Draper

Electrical Connections

Screen operates on 110-120V, 60 hz. AC, .78 amp draw (1.35 with heavy duty

motor).

Screens are shipped with internal wiring complete, with all switches (fully boxed)

and a wiring diagram. Wire connecting screen to switch (or switches) and switch to

power supply should be supplied by installer. Wires should be connected following

the wiring diagram provided, and all wiring should comply with local and national

electrical codes.

All operating switches should be “Off” before power is connected.

Operation

Remove all packing before attempting to operate screen. When screen is ﬁrst

operated, be cautious! Cycle unit down and up several times to conﬁrm

satisfactory operation.

110-120V Single Station Control — 3-position up-off-down switch permits

operation to be stopped at any point. Factory adjusted limit switches automatically

stop screen when fully down or fully up.

110-120V Multiple Station Control — Switches are similar in appearance to 110-

120V Single Station Control. Screen stops when switch is released and may

be restarted in either direction. Factory adjusted limit switches stop screen

automatically when fully down or fully up.

24V Control — Three-button up-stop-down switches stop at any point desired,

operate in any sequence. Factory adjusted limit switches automatically stop screen

when fully down or fully up.

Key Operated Switching — Two kinds of key-operated switches are optionally

available with this unit.

The key-operated power supply switch controls power to the screen and

switches. When it is “off”, the switches will not operate screen. Key may be

removed from the switch in either “on” or “off” position.

A three-position key switch permits the screen to be operated directly by key. In

this case, the screen’s operator must always have a key.

RS232/Ethernet—Serial communication and network communication optionally

available with wall switches, RF or IR remote.

Adjustments

Please Note: Screen limits are factory set for optimum performance of the

screen. A procedure is outlined below for minor tweaks, but any adjustment

of these limits may negatively affect the ﬂatness of the screen surface and

could also void the warranty. Please check with Draper prior to resetting

screen limits.

CAUTION: Always be prepared to shut screen off manually when new

adjustment is being tested. Screen may be severely damaged if viewing

surface is allowed to run too far up or too far down.

CAUTION: Be sure all switches are in “off” position before adjusting limit

switches.

CAUTION: Do not loosen coupling setscrews from the roller shaft, or the

screen surface will rapidly unroll and fall. If setscrew must be loosened

actions should be taken to prevent the roller from turning.

Adjusting “fully up” position — “Up” limit switch is located on right side of

limit switch assembly, immediately behind access door to case. Right hand, hex

head machine screw contacts limit switch button to shut screen off. Turning this

machine screw clockwise will allow surface to run farther up into case. Turning it

counterclockwise will cause screen to stop sooner, farther out of the case.

Adjusting “fully down” position — “Down” limit switch is located on left side of

limit switch assembly, immediately behind access door to case. Left hand, hex

head machine screw contacts limit switch button to shut screen off. Turning this

machine screw clockwise will allow surface to run farther down before stopping.

Turning it counterclockwise will cause screen to stop in a less extended position.

At no time should fabric be unrolled far enough to expose any part of screen roller.

Make all adjustments in small increments, and be sure nut on machine screw is

tight against steel limit switch support before closing access door.

Caution

Read instructions through completely before proceeding.

Follow instructions carefully. Installation contrary to instructions invalidates

warranty.

Do not lift case in center. Lift the ends simultaneously to avoid damage to

case and surface.

4 Entire bottom of screen case should be unobstructed to permit access to

bottom panels for making electrical connections or servicing. Motor end

bracket must be located 1"-6" to right of access door. Idler end bracket must

be located 6"-12" from right end of case. Failure to mount brackets as directed

could cause the case to bow and result in damage to screen.

Keep case level when lifting and mounting. Screen should be installed

level (using a carpenter’s level).

Nothing should be fastened to screen dowel or viewing surface.

Do not touch screen while in motion.

Operating switch (es) packed separately in screen carton. Do not discard

with packing material.

Screen operates on 110-120V, 60 hz., .78 amp draw (1.35 with heavy duty motor).

NOTE: Screen has been thoroughly inspected and tested at factory and found

to be operating properly prior to shipment.

Universal Mounting Bracket

may be suspended from abo ,ve

or mounted to wall. Each bra tcke

consists of a front and back piece

bolted together. 2 required and

supplied on screens up to 14' wide.

3 required and supplied on larger screens

Case

Conduit connection

on left end of case.

Viewing Surface

If you encounter any difﬁculties installing or servicing your Rolleramic screen, call your

dealer or Draper, Inc., Spiceland, Indiana, (765) 987-7999, or fax (765) 987-7142.

Please Note: The Rolleramic is not available with the TorkStar Utility Line Set.

Motor end bracket must be located 1"-6" to right of access door. Idler end

bracket must be located 6"-12" from right end of case. Failure to mount brackets

as directed could cause the case to bow and result in damage to screen.

Produkt Specifikationer

Mærke:	Draper
Kategori:	Projektionsskærm
Model:	Rolleramic 240"
Bredde:	5640 mm
Højde:	3660 mm
Vægt:	109000 g
Monteringstype:	Loft/væg
Drevtype:	Motoriseret
Synlig skærmbredde (W):	4880 mm
Synlig skærmhøjde (H):	3660 mm
Samlet skærmstørrelse (højde x bredde):	366 x 488 cm
Diagonal:	- "
Format:	Video