Eltako DSZ15DM-3x80A Manual

Eltako Ikke kategoriseret DSZ15DM-3x80A

Læs gratis den danske manual til Eltako DSZ15DM-3x80A (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 42 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 21.5 anmeldelser. Har du et spørgsmål om Eltako DSZ15DM-3x80A, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Maximum current 3x80 A. Standby loss 0.5 watt per path only.

Modular device for DIN-EN 60715 TH35 rail mounting in distribution cabinets with IP51

protection class. 4 modules = 70 mm wide and 58 mm deep.

Accuracy class B (1%). With M-bus interface.

It measures active energy by means of the current between input and output.

The internal power consumption of 0.5 watt active power per path is neither metered nor

indicated.

1, 2 or 3 phase conductors with max. currents up to 80 A can be connected. The inrush current

is 4O mA.

The N terminal must always be connected.

The consumption value is stored in non-volatile memory and is displayed again immediately

after a power failure.

The 7 segment LC display is also legible twice within a period of 2 weeks without power

supply.

Power consumption is shown by a bar  ashing at a rate of 1000 times per kWh.

Designed as standard for using as double-tariff meter: Switch over to a second tariff by

applying 230 V to terminals E1/E2.

On the right next to the display are the keys MODE and SELECT. Press them to scroll through

the menu. First the background lighting switches on. The display then shows the total active

energy per tariff, the active energy of the resettable memory RS1 or RS2 as well as the

instantaneous values of consumption, voltage and current per phase.

Error message (false)

When the phase conductor is missing or the current direction is wrong 'false' and the

cor responding phase conductor are indicated on the display.

M-bus data transfer

ɀ On read-out all values are transferred in a telegram.

ɀ The following telegrams are supported:

- Initialisation: SND_NKE Reply: ACK

- Read out meter: REQ_UD2 Reply: RSP_UD

- Change primary address: SND_UD Reply: ACK

- Reset RS1: SND_UD Reply: ACK

- Slave selection for the secondary address Reply: ACK

ɀ The device does not reply to unknown requests

ɀ The transfer rate is detected automatically

ɀ The device has a voltage monitor. In case of voltage loss, all registers are saved in the

EEPROM.

Changing the M-bus primary address:

To change the M-bus primary address, hold down SELECT for 3 s. In the menu that appears,

press MODE to increment the address by 10. Press SELECT to increment by 1. When the

required primary address is set, wait until the main menu reappears.

Secondary address:

ɀ It is possible to communicate with the energy meter according to the standard EN13757

with help of the secondary address.

ɀ The use of wildcards is possible.

Detailed information are available in the operating manuals at www.eltako.com.

M-bus three-phase meter for use DSZ15DM-3x80A with display

and MID approval

Temperature at mounting location: -25°C up to +55°C.

Storage temperature: -25°C up to +70°C.

Relative humidity: annual average value <75%.

28 380 512 - 1

Only skilled electricians may install this electrical equipment otherwise there is the risk

of  re or electric shock!

Typical connection:

4-wire-connection 3x230/400 V

Technical data

Rated voltage, extended range 3x230/400 V, 50 Hz,

-2O%/+15%

Reference current

ref

(Limiting current

max

) 3x0.5 - 10 (80) A

Internal consumption active power 0.5 W per path

Display LC display 7 digits,

therefrom 1 digit after the decimal point

Accuracy class ±1% B

Inrush current according to accuracy class B 4O mA

Operating temperature -25/+55°C

Bus system M-Bus

Bus length According to M-bus speci cations

Transfer rates 300, 2400, 9600 baud

Response time Write up to 60 ms

(system response time) Read up to 60 ms

Terminal cover sealable Terminal cover claps

Protection degree lP50 for mounting in distribution cabines

with protection class IP51

Maximum conductor cross section

L terminals 25 mm

N terminals 16 mm

M-bus terminals and tariff terminals 6 mm

Recommended torque

L terminals 2,0 Nm (max. 2,5 Nm)

N terminals 1,5 Nm (max. 2,0 Nm)

M-bus terminals and tariff terminals 0,8 Nm (max. 1,2 Nm)

EC type examination certi cate 0120/SGS0204

The energy meter is used indoors.

Mechanical environmental conditions class M1

Electromagnetic environmental conditions class E2

The carrying capacity of cables and wires is de ned in DIN VDE 0298-4.

The torques for screw terminals are mentioned in DIN EN 60999-1.

To avoid damages at the energy meter, the recommended torque values for each terminal must not be exceeded!

Produkt Specifikationer

Mærke:	Eltako
Kategori:	Ikke kategoriseret
Model:	DSZ15DM-3x80A

Har du brug for hjælp?

Hvis du har brug for hjælp til Eltako DSZ15DM-3x80A stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Eltako Manualer

Eltako MS Manual

31 August 2024

Eltako FUD61NP-230V Manual

30 August 2024

Eltako FT4F-rw Manual

30 August 2024

Eltako FT4F-wg Manual

30 August 2024

Eltako DL-PD-300W-RLC-HS Manual

30 August 2024

Eltako DSZ15DM-3x80A Manual

30 August 2024

Eltako FTN14 Manual

30 August 2024

Eltako FT55R Manual

30 August 2024

Eltako FUD71L Manual

30 August 2024

Eltako FTS14EM T Manual

30 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Blustream HDBaseT HEX70ARC-KIT Manual

21 November 2025

Vevor AB-019 Manual

21 November 2025

Vevor BTC002D Manual

21 November 2025

Vevor A70002102 Manual

21 November 2025

Vevor JZH-811 Manual

21 November 2025

Vevor 3870 Manual

21 November 2025

Blustream HDBaseT HMXL44CS-KIT Manual

21 November 2025

American Audio Wave Manual

21 November 2025

Vevor B-5436 Manual

21 November 2025

Vevor AR-BMW-016 Manual

21 November 2025