Eltako FMZ14 Manual

Eltako Ikke kategoriseret FMZ14

Læs gratis den danske manual til Eltako FMZ14 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Eltako FMZ14, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Multifunction time relay with 10 functions,

1 CO contact potential free 10A/250V AC,

incandescent lamps 2000 watts*, with

DX technology. Bidirectional. Only 0.4 watt

standby loss.

Modular device for DIN-EN 60715 TH35

rail mounting.

1 module = 18 mm wide, 58mm deep.

Connection to the Eltako-RS485 bus. Bus

cross wiring and power supply with jumper.

Wireless window contacts (FTK) and

window handles at opened

windows with

the function NO or NC can be taught-in.

Several FTK and (or) window handles

are linked to each other. If a direction

switch is taught-in, a function (e.g. TI)

can be started using the top switch

(START) and stopped with the bottom

switch (STOP).

Patented Eltako Duplex technology allows

you to switch normally potential free

contacts in zero passage switching when

230V A/C voltage 50 Hz is switched.

This drastically reduces wear. To achieve

this, simply connect the N conductor to

the terminal (N) and L to K(L). This

results in an additional standby

consumption of only 0.1 watt.

If supply voltage fails, the two contacts

switch off. When power is restored,

contact 1 closes.

Only skilled electricians may install

this electrical equipment otherwise

there is the risk of fire or electric

shock!

Temperature at mounting location:

-20°C up to +50°C.

Storage temperature: -25°C up to +70°C.

Relative humidity:

annual average value <75%.

RS485 bus actuator

Multifunction time relay

FMZ14

30 014 009 - 2

valid for devices from production week

40/17 (see bottom side of housing)

Typical connection

Time setting between 0.5 second and

20 hours.

Function rotary switches

Teach-in takes place using the top and

middle rotary switches and then the time

is set. T is the time base and xT the

multiplier.

The function is selected using the bottom

rotary switch:

RV = off delay

AV = operate delay

TI =

clock generator starting with impulse

TP = clock generator starting with pause

IA = impulse controlled operate delay

(e.g. automatic door opener)

EW = fleeting NO contact

AW = fleeting NC contact

ARV= operate and release delay

ON = Permanent ON

OFF= Permanent OFF

The LED below the upper function rotary

switch performs during the teach-in

process

according to the operation man-

ual.

It shows control commands by short

flickering during operation.

* The maximum load can be used

starting at a delay time or clock cycle

of 5 minutes. The maximum load will

be reduced for shorter times as follows:

up to 2 seconds 15 %, up to 2 minutes

30%, up to 5 minutes 60%.

Description of functions

t1 t2 t1 t2

Wireless

input

K(L)- 2

ARV

Wireless

input

K(L)- 2

t1 t2 = 3s

Wireless

input

K(L)- 2

Wireless

input

K(L)- 2

Wireless

input

K(L)- 2

t1 t2 t1

Wireless

input

K(L)- 2

Wireless

input

K(L)- 2

Wireless

input

K(L)- 2

Teaching-in wireless sensors in wire-

less actuators

All sensors must be taught-in in the

actuators so that they can detect and

execute commands.

After the address of the FAM14 was

assigned, its lower LED flashes green

for 5 seconds and the LED of the FMZ14

goes out.

Delete device configuration:

Set the middle rotary switch to CLR.

The LED flashes nervously. Then turn

the upper rotary switch within 10 seconds

3 times to the leftmost stop (anticlock wise)

and turn it back again. The LED stops

flashing and goes out after 5 seconds.

The factory settings are restored.

Delete device configuration and device

address:

Set the middle rotary switch to CLR. The

LED flashes nervously. Then turn the upper

rotary switch within 10 seconds 6 times

to the leftmost stop (anticlock wise) and

turn it back again. The LED stops flashing

and goes out after 5 seconds. The factory

settings are restored and the device

address deleted.

Configure FMZ14:

The following points can be configured

with the PC tool PCT14:

■

duty cycle pulse control (IA)

■

teaching-in of wireless pushbuttons

with single or double click

■

add or change sensors

CAUTION! Don't forget 'disconnect FAM'

in the PC tool. While the connection

from the PC tool to the FAM14 exists,

no wireless commands are executed.

Teach-in confirmation telegram of

another bus actuator to the FMZ14:

As in the teach-in procedure, only set

the middle rotary switch to LRA instead

to LRN.

Teach-in 'switch OFF' as 'central OFF'.

When an actuator is ready for

teach-in (the LED flashes at a

low rate), the very next incoming

signal is taught-in. Therefore,

make absolutely sure that you

do not activate any other sensors

during the teach-in phase.

Eltako GmbH

D-70736 Fellbach

Technical Support English:

Michael Thünte +49 176 13582514

thuente@eltako.de

Marc Peter +49 173 3180368

marc.peter@eltako.de

eltako.com

34/2017 Subject to change without notice.

Must be kept for later use!

We recommend the housing for operating

instructions GBA14.

Teaching-in sensors

1.Set the top rotary switch to the required

teach-in function:

2 = teach-in 'central OFF';

3 = teach-in universal switch;

5 = teach-in direction switches;

Direction switches are completely

taught-in automatically when operating

the top or bottom pushbutton. The

side on which the pushbutton is first

operated is defined for START and the

other side for STOP.

6 = teach-in FTK and window handle

as NC contact;

8 = teach-in FTK and window handle

as NO contact.

2.Set the middle rotary switch to LRN.

The LED flashes at a low rate.

3.Operate the sensor to be taught-in.

The LED goes out.

To teach-in further sensors, turn the

middle rotary switch briefly away from

position LRN. Continue the procedure

from pos 1.

Set the time after teach-in with the mid-

dle and top rotary switches.

Teaching-in actuator FM

Z14

The teach-in memory is clear on deliv-

ery from the factory. To ensure that a

device was not previously taught-in,

clear the complete memory:

Turn the middle rotary switch to CLR.

The LED flashes at a high rate. Within

10 seconds, turn the top rotary switch

three times to right stop (turn clock-

wise) and back again. The LED stops

flashing and goes out after 2 seconds.

All taught-in sensors are cleared.

Clear single taught-in sensors: in the

same way as in the teach-in procedure,

except that you set the middle rotary

switch to CLR instead of LRN, and oper-

ate the sensor. The LED previously flash-

ing at a high rate goes out.

Assign device address for the FMZ14:

The rotary switch on the FAM14 is set to

position 1, its lower LED flashes red.

The middle rotary switch of the FMZ14 is

set to LRN, the LED flashes smoothly.

Produkt Specifikationer

Mærke:	Eltako
Kategori:	Ikke kategoriseret
Model:	FMZ14

Har du brug for hjælp?

Hvis du har brug for hjælp til Eltako FMZ14 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Eltako Manualer

Eltako MS Manual

31 August 2024

Eltako FUD61NP-230V Manual

30 August 2024

Eltako FT4F-rw Manual

30 August 2024

Eltako FT4F-wg Manual

30 August 2024

Eltako DL-PD-300W-RLC-HS Manual

30 August 2024

Eltako DSZ15DM-3x80A Manual

30 August 2024

Eltako FTN14 Manual

30 August 2024

Eltako FT55R Manual

30 August 2024

Eltako FUD71L Manual

30 August 2024

Eltako FTS14EM T Manual

30 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Krups Perfectmix Cook KB835D Manual

19 August 2025

Sauermann CTV 210-R Manual

19 August 2025

Emos DCLW31 Manual

19 August 2025

Body Solid GAB350 Manual

19 August 2025

Tefal Classic PP1114 Manual

19 August 2025

Tefal Premio PP1212 Manual

19 August 2025

Tefal Avanti BF2738 Manual

19 August 2025

Krups Expert RE8001 Manual

19 August 2025

Tefal Maestro FV1850 Manual

19 August 2025

Moulinex Mini Multi LM126G Manual

19 August 2025