Eltako FUD70S-230V-rw Manual

Eltako Ikke kategoriseret FUD70S-230V-rw

Læs gratis den danske manual til Eltako FUD70S-230V-rw (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Eltako FUD70S-230V-rw, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Universal dimmer switch, power MOSFET

up to 400 W. Automatic lamp detection.

With adjustable minimum brightness or

maximum brightness and dimming speed.

With switching operation for light alarm

clocks, children‘s rooms and snooze

function. Also with light scene control by

PC or wireless pushbuttons. Bidirectional

wireless and with repeater function.

Only 0.6 watt standby loss.

Mounting in the 230 V power supply cord,

e.g. in false ceilings. 100 mm long,

50 mm wide and 31 mm high.

With bidirectional wireless; in addition, a

repeater function can be switched in. Every

change in state and incoming central com-

mand telegrams are conrmed by a wirel-

ess telegram. This wireless tele gram can be

taught-in in other actuators, in the GFVS

software and in FUA55 universal displays.

Universal dimmer switch for lamps up to

400 W, depending on ventilation conditions.

Dimmable energy saving lamps ESL and

dimmable 230V LED lamps, additionally

depending on the lamps electronics.

Zero passage switching with soft ON and

soft OFF to protect lamps.

The brightness level is stored on switch-off

(memory). In case of a power failure the

switch position and the brightness stage

Wireless actuator

Universal dimmer switch

FUD70S-230V as cord switch

Temperature at mounting location:

-20°C up to +50°C.

Storage temperature: -25°C up to +70°C.

Relative humidity:

annual average value <75%.

30 100 852 - 1

Only skilled electricians may install this

electrical equipment otherwise there is

the risk of re or electric shock!

valid for devices from production week

14/15 (see bottom side of housing)

are stored and may be switched on when

the power supply is restored.

Automatic electronic overload protection

and overtemperature switch-off.

Function rotary switches

The left rotary switch determines the

operation, whether automatic lamp detection

or special comfort positions should work:

AUTO allows the dimming of all lamp

types.

EC1 is a comfort position for energy saving

lamps, which which by design must be

turned on with an increased voltage so that

they switch on again in cold state

EC2 is a comfort position for energy saving

lamps, which by design won’t switch on

again when dimmed down. Therefore

Memory is switched off in this position.

LC1 is a comfort position for dimmable 230 V

LED lamps which are not being dimmed

down enough when set to AUTO (trailing

phase angle) dependent on the construction

and must therefore be forced to leading

phase angle.

LC2 and LC3 are comfort positions for

dimmable 230 V LED lamps like LC1, but with

different dimming curves.

In positions EC1, EC2, LC1, LC2 and LC3

inductive (wound) transformers may not

be used. In addition, the maximum number

of dimmable LED lamps may be lower by de-

sign than in the AUTO position.

The minimum brightness (fully dimmed

down) or maximum brightness (fully

dim med up) is adjustable with the middle

rotary switch. In the setting LRN up to

30 pushbuttons can be assigned, of which

one or more central pushbuttons.

The dimming speed is adjustable using the

right dimming speed rotary switch on the

side. At the same time, the soft ON and soft

OFF periods are changed.

The pushbuttons can be taught-in

either as direction switches or universal

switches:

When installed as a direction switch, one

side is then 'switch on and dim up' and the

other side is 'switch off and dim down'.

A double-click on the switch-on side activa-

tes automatic dim-up to full brightness at

dim speed. A double click on the switch-off

side activates the snooze function. The

children‘s room function is implemented on

the switch-on side.

As a universal switch, change the direction

by briey releasing the pushbutton. With

switching operation for children‘s rooms and

snooze function.

Switching for light alarm clocks: A wire-

less signal of a time clock which was

taught-in accordingly starts the wake up

function by switching on the light at the

lowest brightness level and dims up slowly

until the maximum level is reached.

Dependent on the set dim speed the wake

up time is between 30 and 60 minutes.

The dimming process is stopped by tapping

briey, e.g. on the hand-held transmitter.

At setting ESL the switching for light alarm

clocks is not possible.

Switching operation for children‘s rooms

(universal switch or direction switch on the

switch-on side): If the light is switched on

by holding down the pushbutton, it starts at

the lowest brightness level after approx. 1

second and dims up slowly as long as the

pushbutton is held down. The last saved

brightness level is not modied.

Snooze function (universal switch or

direction switch on the switch-off side):

With a double impulse the lighting is

dimmed down from the current dimming

position to the minimum brightness level

and switched off. The current dimming

position as well as the adjustable minimum

brightness level determine the dimming

time (max. = 60 minutes) which can be

reduced as required. It can be switched off

at any time by short-time control com-

mands during the lighting is dimmed down.

Light scenes on the PC are set and

retrieved using the Wireless Visualisation

and Control Software GFVS. A description

of the GFVS is at „eltako-wireless.com“. One

or several FUD70S devices must be taught

in on the PC as dimming switches with

percentage brightness values.

Lights scenes with wireless switches are

taught-in on the FUD. Up to four brightness

values are retrievable using a direct light

scene pushbutton (pushbutton with double

rocker, top left = light scene 1, top right =

light scene 2, bottom left = light scene 3 and

bottom right = light scene 4) and/or using a

sequential light scene pushbutton (push-

button or one half of a double pushbutton,

press top = next light scene, press bottom =

previous light scene).

If a wireless motion-brightness sensor

FBH is taught-in, the switching threshold

will be set with the right rotary switch while

teaching-in, in which, depending on the

brightness (in addition to the movement),

the lighting turns on with memory voltage

(approximately 30lux in the OFF position and

up to 300lux in the max position). If the FBH

is taught-in in the ON position, it will only be

evaluated as a motion detector. A delay of

1 minute is xed in the FBH.

If a wireless brightness sensor FHD60 is

taught-in, the switching threshold will be

set with the right rotary switch while

teaching-in, in which, depending on the

brightness, the lighting turns on or off

(approximately 0 lux in the OFF position and

up to 50 lux in the ON position). When falling

below the brightness threshold, it will be

turned on with memory value. It will be

turned off at a brightness > 200 lux.

The LED on the side behind the left rotary

switch performs during the teach-in

pro cess according to the operating

instructions. It shows wireless control com-

mands by short ickering during operation.

Technical data

Incandescent and up to 400 W

halogen

lamps 230 V (R)

Inductive transformers (L) up to 400 W

2)3)

Electronic transformers (C) up to 400 W

2)3)

Dimmable energy up to 400 W

saving lamps ESL

Dimmable 230 V LEDs up to 400 W

Max./min. temperature +50°C/-20°C

at mounting location

Standby loss (activ power) 0,6 W

For lamps with 150 W max.

Per dimmer it is only allowed to use max. 2 inductive

(wound) transformers of the same type, further-

more no-load operation on the secondary part is

not permitted. The dimmer might be destroyed.

Produkt Specifikationer

Mærke:	Eltako
Kategori:	Ikke kategoriseret
Model:	FUD70S-230V-rw

Har du brug for hjælp?

Hvis du har brug for hjælp til Eltako FUD70S-230V-rw stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Eltako Manualer

Eltako MS Manual

31 August 2024

Eltako FUD61NP-230V Manual

30 August 2024

Eltako FT4F-rw Manual

30 August 2024

Eltako FT4F-wg Manual

30 August 2024

Eltako DL-PD-300W-RLC-HS Manual

30 August 2024

Eltako DSZ15DM-3x80A Manual

30 August 2024

Eltako FTN14 Manual

30 August 2024

Eltako FT55R Manual

30 August 2024

Eltako FUD71L Manual

30 August 2024

Eltako FTS14EM T Manual

30 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Blustream HDBaseT HEX70ARC-KIT Manual

21 November 2025

Vevor AB-019 Manual

21 November 2025

Vevor BTC002D Manual

21 November 2025

Vevor A70002102 Manual

21 November 2025

Vevor JZH-811 Manual

21 November 2025

Vevor 3870 Manual

21 November 2025

Blustream HDBaseT HMXL44CS-KIT Manual

21 November 2025

American Audio Wave Manual

21 November 2025

Vevor B-5436 Manual

21 November 2025

Vevor AR-BMW-016 Manual

21 November 2025