Epcom X3225 Manual

Epcom Ikke kategoriseret X3225

Læs gratis den danske manual til Epcom X3225 (9 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Epcom X3225, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/9

Specications:

Model Length LEDs Watts Amps/12

VDC

Amps/24

VDC Lumens Fuse

Needed

EW3108-F 8” 6 30 3.3 1.1 1680 5

EW3108-S 8” 6 30 3.2 1 1680 5

EW3114 14” 12 60 5.7 2.1 3360 7.5

EW3124 24” 21 105 8.7 3.6 5880 10

EW3136 36” 33 165 13 6.6 9240 15

EW3149 49” 45 225 18.5 7.9 12600 25

EW3208-F 8” 12 60 4.5 2.2 3360 7.5

EW3208-S 8” 12 60 4.7 2.3 3360 7.5

EW3214 14” 24 120 9.3 4.5 6720 15

EW3225 25” 44 220 17.3 8.4 12320 20

EW3233 33” 60 300 25 12 16800 30

EW3242 42” 76 380 32 15.5 21280 40

EW3312-F 12” 6 60 4.4 2.1 3350 5

EW3312-S 12” 6 60 4.4 2.1 3350 5

EW3324 24” 12 120 7.9 3.9 8400 10

EW3336 36” 18 180 12 5.8 12600 15

IMPORTANT! Read all instructions before installing and using. Installer: This manual must be

delivered to the end user.

Do not install and/or operate this safety product unless you have read and understand the safety

information contained in this manual.

1. Proper installation combined with operator training in the installation, use, care and maintenance of vehicle equipment accessories is

essential to ensure the safety of you and those you are trying to protect.

2. Exercise caution when working with live electrical connections.

3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high

current arcing, which can cause personal injury and/or severe vehicle damage, including re.

4. Proper placement and installation are vital to the performance of this worklamp. Install this product so that output

performance of the system is maximized and the controls are placed within convenient reach of the operator so that s/he can

operate the system without losing eye contact with the work area.

5. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use, the

vehicle operator should ensure the projection of the beam is not blocked by vehicle components (i.e., open trunks

or compartment doors), people, vehicles, or other obstructions.

6. The manufacturer assumes no liability for any loss resulting from the use of this device.

WARNING!

Failure to install or use this product according to manufacturer’s recommendations may result in property

damage, serious bodily/personal injury, and/or death to you and those you are seeking to protect! Check wattage

before installing light to avoid possible equipment damage.

SAA

NOTE: Black die cast Aluminum housing gets very hot to the touch after operating constantly for several hours.

Installation and Operation Instructions

LED UTILITY BARS

ECCO LED Utility Bars are designed to provide superior lighting performance and withstand the harshest environments. Avail-

able in various lengths, LED wattages, and with either ood, spot or combination beam patterns. These robust, high output

lights feature the latest LEDs and reectors designed for maximum light projection. The coated die-cast aluminum housing is

fully sealed for protection against water ingress, vibration, shock and impact. Two (pivoting) mounting methods are included,

choose from heavy duty side-mounted pedestal brackets or bottom-mounted carriage bolts. Additional benets of LED tech-

nology include a bright white beam, low current consumption and a long, maintenance free service life. This manual provides

information about installation, function, safety, maintenance, replacement parts, and warranty.

920-0406-00 Rev. D Page 1 of 9

Pedestal Mount

Pivot Mount

Installation (Pedestal Mount):

1. Attach the bolt through the hole and side bracket using

the spring locking bolt. See Figure 1.

2. Select a mounting surface to match the diameter of the

included bracket(s).

3. Put the shockproof pad on the mounting plate, then feed

the hexagon bolt through the side of the bracket. Put the

plain washers and locking spring washer on the bolt, then

fasten it. See Figure 2.

4. Connect the power line to the corresponding power

connector.

5. Adjust beam location of the unit and tighten the lock nut

with a wrench.

920-0406-00 Rev. D Page 2 of 9

Installation (Pivot Mount):

1. First, put hexagon bolt through movable bracket,

shockproof pad and the bracket, then fasten hex nut. See

Figure 3.

2. Put two nished brackets into the bottom of bracket round

bar, then adjust these two brackets in proper position, then

fasten it. See Figure 4.

3. Put hexagon bolt through bracket and mounting plate,

then put spring meson, then fasten nut. See Figure 5.

4. Connect the power line to the corresponding power

connector.

Figure 1

Figure 2

Figure 3

Figure 4

Figure 5

Produkt Specifikationer

Mærke:	Epcom
Kategori:	Ikke kategoriseret
Model:	X3225

Har du brug for hjælp?

Hvis du har brug for hjælp til Epcom X3225 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Epcom Manualer

Epcom X67-R Manual

29 August 2024

Epcom X303N Manual

29 August 2024

Epcom XLL-1088-RB Manual

29 August 2024

29 August 2024

29 August 2024

29 August 2024

29 August 2024

29 August 2024

29 August 2024

29 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Ikea KOPPLA 404.095.77 Manual

31 Juli 2025

Berner Architectural Elite 8 Manual

31 Juli 2025

Tripp Lite Protect It! TLP26PD30WCAM Manual

31 Juli 2025

Yealink RT20U Manual

31 Juli 2025

Tripp Lite PR60 Manual

31 Juli 2025

Advantech UTC-520J Manual

31 Juli 2025

Tripp Lite Protect It! TLM615SA Manual

31 Juli 2025

Tripp Lite SU6000XFMR2UTAA Manual

31 Juli 2025

Tripp Lite IBAR4-6D Manual

31 Juli 2025

Tripp Lite Protect It! TLP606TAA Manual

31 Juli 2025