Epcom X6262A Manual

Epcom Ikke kategoriseret X6262A

Læs gratis den danske manual til Epcom X6262A (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Epcom X6262A, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Page 1 of 2

Installation and Operation Instructions

LED Beacons

Specications:

Size: 3.8”(D) x 2.8”(W) x 4.9”(H)

Weight: 0.8 lb.

Current draw: 0.5 Amps max. (@+12.8VDC)

Locate the unit in the desired position on a at mounting surface, and

using the base as a template, mark the two mounting hole locations.

Drill the holes using a 7/32” (0.219”) drill size. Drill a third hole,

exterior to the base to serve as a wire access hole. Mount the unit

using #10 hardware.

Installation & Mounting:

Flush Mount:

Pipe Mount:

Carefully remove the LED beacon from packaging. Examine the unit for

transit damage. If damage is found, return product to your local dealer for

warranty replacement. Do not use damaged or broken parts.

Maintenance-free LED Beacons feature the latest

LEDs and a Pulse8 ash pattern, producing a warning

signal ideally suited to industrial applications. This

cost effective unit has a wide operating range of

12-80V, making it the perfect light for use on electric

vehicles.

1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are essential to ensure

the safety of you and those you are seeking to protect.

2. Exercise caution when working with live electrical connections.

3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current arcing,

which can cause personal injury and/or severe vehicle damage, including re.

4. Proper placement and installation are vital to the performance of this warning device. Install this product so that output performance of the

system is maximized and the controls are placed within convenient reach of the operator so that s/he can operate the system without losing

eye contact with the roadway.

5. Do not install this product or route any wires in the deployment area of an air bag. Equipment mounted or located in an air bag deployment

area may reduce the effectiveness of the air bag or become a projectile that could cause serious personal injury or death. Refer to the

vehicle owner’s manual for the air bag deployment area. It is the responsibility of the user/operator to determine a suitable mounting location

ensuring the safety of all passengers inside the vehicle particularly avoiding areas of potential head impact.

6. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use, the vehicle operator

should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors), people,

vehicles or other obstructions.

7. The use of this or any other warning device does not ensure all drivers can or will observe or react to a warning signal. Never take the right-

of-way for granted. It is your responsibility to be sure you can proceed safely before entering an intersection, driving against trafc, respond-

ing at a high rate of speed, or walking on or around trafc lanes.

8. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws regarding

warning signal devices. Therefore, the user should check all applicable city, state, and federal laws and regulations. The manufacturer as-

sumes no liability for any loss resulting from the use of this warning device.

Do not install and/or operate this safety product unless you have read and understand the safety information

contained

Failure to install or use this product according to manufacturer’s recommendations may result in property damage, serious injury, and/or death to

those you are seeking to protect!

WARNING!

Caution: When drilling into any vehicle surface, make sure the area

is free from any electrical wires, fuel lines, vehicle upholstery, etc. that

could be damaged

1. Larger wires and tight connections will provide longer service life for components. For high current wires it is highly recommended that terminal blocks or

soldered connections be used with shrink tubing to protect the connections. Do not use insulation displacement connectors (e.g., 3M Scotchlock type con-

nectors).

2. Route wiring using grommets and sealant when passing through compartment walls. Minimize the number of splices to reduce voltage drop. High ambient

temperatures (e.g., under-hood) will signicantly reduce the current carrying capacity of wires, fuses, and circuit breakers. All wiring should conform to the

minimum wire size and other recommendations of the manufacturer and be protected from moving parts and hot surfaces. Looms, grommets, cable ties, and

similar installation hardware should be used to anchor and protect all wiring.

3. Fuses or circuit breakers should be located as close to the power takeoff points as possible and properly sized to protect the wiring and devices.

4. Particular attention should be paid to the location and method of making electrical connections and splices to protect these points from corrosion and loss of

conductivity.

5. Ground termination should only be made to substantial chassis components, preferably directly to the vehicle battery.

6. Circuit breakers are very sensitive to high temperatures and will “false trip” when mounted in hot environments or operated close to their capacity.