Fantini Cosmi O70RL Manual

Fantini Cosmi Ikke kategoriseret O70RL

Læs gratis den danske manual til Fantini Cosmi O70RL (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Fantini Cosmi O70RL, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Attachment

M30x1.5

Radio band

EU868

RF power

< +14dbm

Radio modulation

LoRa

Firmware update

via radio (OTA)

Power supply

2 alkaline batteries 1.5V – LR6 – AA

(do not use rechargeable batteries)

Autonomy

up to 24 months (dependent on mode of use)

TECHNICAL DATA

Temperature display Celsius (°C)

Temperature adjustment scale 2

30 °C; increment 0.1 °C

Operating temperature

0 to 40°C

Storage temperature -20

65 °C

Relative storage humidity 20

80% (90% without condensation)

Protection rating IP30

Size

89.8 x Ø 54.2 mm

Directive 2014/30/EU (EMC); Directive 2014/35/EU (LVD); Directive 2014/53/EU (RED)

Product not manufactured in Italy.

At any time it is however possible to activate the radio function and associate the O70RL

with the Fantini Cosmi RL multi-zone temperature control system (chapter 2.1 - RADIO

SYSTEM CONFIGURATION).

ENG

WIRELESS RADIATOR THERMOSTAT

4 - CHANGING SETTINGS

1. To change settings, activate the display and press the dial for 15 seconds until the Insscreen

appears, then release;

15 sec.

2. Turn the dial to select the parameter you wish to change (see list) and press SETTINGS MENU

to enter;

3. Turn the dial to select the desired value and press to confirm. When released, a flash confirms

the saving of changes;

4. To exit the settings menu completely, wait 10 seconds or press the dial for 3 seconds.

3 sec.

SETTINGS MENU

Setting brightness

The default value can be changed to adjust the brightness of the display.

Default value = 03

01 (min) - 05 (max)

Room temperature display

When this function is enabled, the display will show the detected room temperature when it is

switched on.

Default value = OFF (disabled)

OFF = Turning the dial always displays the desired temperature

ON = Pressing the dial to switch on the display shows the room temperature

Display orientation

Allows you to change the desired display orientation.

Correction of detected temperature (OFFSET) *

If you notice a gap between the temperature measured in the room (thermometer) and the

temperature displayed on the valve, you can correct the value to be displayed.

Default value = 0°C

-5 - 5

Minimum temperature limit *

A user-settable minimum temperature threshold (Set Point) can be set.

Default value = 2°C

2.0 °C ÷ tH

Maximum temperature limit *

A maximum temperature threshold can be set by the user (Set Point).

Default value = 30°C

tL ÷ 30.0 °C

Anti-seize

The frequency of automatic forced valve actuation can be set. This function remains active

even when the thermostat is in OFF mode.

Default value = 30 days

1 - 99, OFF

View release

The display shows the firmware and hardware version installed on the device.

Temperature control modes

Displays the valve setting mode.

LOc = room temperature reading from O70RL (default)

Ren = room temperature reading from remote thermostat (if present)

dC = direct control

Open window function

When this function is enabled, the device goes into OFF when an abrupt

drop in room temperature is detected, avoiding energy waste, and the

open window icon appears on the display.

To restore normal operation, wait 30 minutes or use the control dial.

Default value = OFF (disabled)

OFF = Function disabled

ON = Function enabled

* Function only available for stand-alone use. If connected to the multi-zone system, the parameter

will be managed by the CH180WIFIRL master device.

1 - DESCRIPTION

Ring nut

Thermostatic head

and battery cover

Adjustment and

confirmation dial

Display

Safety lock

Radio signal

Set piont temperature /

room temperature

Low battery warning

Open window function active

O70RL can be mounted either vertically or horizontally.

O70RL installs on all thermostat valves with M30x1.5 connection;

If necessary, use the most suitable adapter (not included in the package) for other valve

types:

CODE DESCRIPTION

309703A IRSAP/CALEFFI valve adapter

309704 Giacomini valve adapter

309706A FAR valve adapter

tate the O70RL body so that the display is in a clearly visible position.

fine the orientation of the display by turning the dial until the word is correctly UP

positioned; confirm by pressing the dial.

dio activation:

Combination with multi-zone temperature control system

Select YES to associate the thermostat with the Fantini Cosmi RL multi-zone

temperature control system (chapter 2.1 - RADIO SYSTEM CONFIGURATION -

paragraph 2). To exit the radio pairing phase, perform a reset as per point

4.1 - RESTORING FACTORY SETTINGS.

Using the device in stand-alone mode

Select NO to use the device without association with the Fantini Cosmi RL

multi-zone temperature control system.

4.1 - RESTORING FACTORY SETTINGS

Remove the battery compartment cover;

Press and hold the reset button until the display is reset;

Replace the cover and repeat the initial installation procedure (Chapter 1 - INSTALLATION - paragraph 4).

* when combined with CH180WIFIRL

nsert the cover;

O70RL will perform automatic calibration which will also occur also

each time the cover is reinserted. During the calibration phase, the

screen shown here is displayed.

In the event of a calibration error, the screen Erc

appears on the display. Check that the valve is properly secured or

check the condition of the batteries.

3.4 - OPEN WINDOW FUNCTION

When this function is enabled (see Chapter ), the device goes into OFF when 4 - CHANGING SETTINGS

an abrupt drop in the room temperature is detected, avoiding energy waste.

move the thermostat cover and insert two AA 1.5 V batteries, observing correct polarity;

1.5V LR6 (AA)

The initial screen will flash on the display:

Screw the ring nut of the thermostat onto the threaded connection of the radiator valve.

2 - INSTALLATION

3.2 - SETTING THE TEMPERATURE

With the display active, turn the dial to raise or lower the desired temperature.

To confirm, wait a few seconds or press the rotary dial; a flash

indicates that the changes have been saved.

Lowering the temperature beyond the minimum limit will

activate the “OFF” mode and the antifreeze function at 2°C.

2.1 - RADIO SYSTEM CONFIGURATION (OPTIONAL)

Activate the radio function by pressing and holding the rotary dial for 10 seconds after activation

of the display, until the screen appears:rF

10 sec.

Perform pairing from the CH180WIFIRL master device by selecting the MAC address of the

thermostat to be paired (as shown on the label located under the cover).

MAC address

QR code for Intelliclima+ App

Alternatively, the thermostat can be associated with the CH180WIFIRL master device directly

from the Intelliclima+ application by framing the QR code on the label.

To confirm successful association with the CH180WIFIRL, the desired

temperature (default 20.0 °C) and the radio icon appear on the thermostat

display:

At any time, it is possible to exit the radio pairing phase by resetting the device as indicated

under .4.1 - RESTORING FACTORY SETTINGS

3 - USE

3.1 - SWITCHING ON THE DISPLAY AND TEMPERATURE DISPLAY

After 5 seconds of inactivity, the O70RL will go into stand-by mode, switching off

the display. To reactivate the display, press or turn the control dial slightly. The

desired temperature appears on the display (default 20.0 °C).

When the batteries are running low, the icon flashes once every hour. When the batteries are completely

depleted, it will no longer be possible to operate the device, which will go to OFF.

Low battery test: remove and replace cover. If the low battery symbol flashes, this means that the

batteries are running low and need to be replaced.

LOW BATTERY WARNING

To deactivate the safety lock function, with the display active, press the dial again for 5 seconds until

the lock icon disappears from the display.

3.3 - SAFETY LOCK

With the display active, it is possible

to deactivate the setting change by

pressing the dial for 5 seconds until the

LOc screen appears.

Activation of the function is confirmed

by the presence of the lock icon on the

display.

5 sec.

Thank you for purchasing the Fantini Cosmi wireless radiator thermostat, model O70RL.This manual

contains all the information required for a correct installation and use. You can also download this manual

in digital format and in several languages by framing the QR code below and entering the product code.

FANTINI COSMI S.P.A.

Via Dell’osio, 6 - 20049 Caleppio di Settala (Mi) - ITALY

Email: info@fantinicosmi.it - www.fantinicosmi.it

70RL

O70RL

pdf.fantinicosmi.it

ITALIANO

ENGLISH

FRANÇAIS

ESPAÑOL

DEUTSCH

РУССКИЙ

УКРАЇНСЬКИЙ

...

Produkt Specifikationer

Mærke:	Fantini Cosmi
Kategori:	Ikke kategoriseret
Model:	O70RL

Har du brug for hjælp?

Hvis du har brug for hjælp til Fantini Cosmi O70RL stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Fantini Cosmi Manualer

Fantini Cosmi A03-A04 Manual

21 Juli 2025

Fantini Cosmi Intellicomfort CH150MB Manual

1 Juli 2025

Fantini Cosmi 343 Manual

30 Juni 2025

Fantini Cosmi ASE Manual

23 Juni 2025

Fantini Cosmi K55A Manual

22 Juni 2025

Fantini Cosmi AD23 Manual

22 Juni 2025

Fantini Cosmi B12MN Manual

21 Juni 2025

Fantini Cosmi K15A Manual

21 Juni 2025

Fantini Cosmi B01 Manual

21 Juni 2025

Fantini Cosmi A96 Manual

21 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

MSW -AIRS1290ASN Manual

17 August 2025

Mueller SC 98.47 pro Manual

17 August 2025

MSW -WPW-20 Manual

17 August 2025

Planet WGS-4215-8P2X Manual

17 August 2025

Mueller SC 98.40 knx Manual

17 August 2025

MSW -MS76A Manual

17 August 2025

MSW -HFCV-40-C Manual

17 August 2025

Mars Gaming MCPU-XU9 Manual

17 August 2025

Mars Gaming MPS5-B Manual

17 August 2025

B-Tech BT8566 Manual

17 August 2025