Fantini Cosmi OCV1A Manual

Fantini Cosmi Ikke kategoriseret OCV1A

Læs gratis den danske manual til Fantini Cosmi OCV1A (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Fantini Cosmi OCV1A, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

OCV1A Control Unit – Instructions for Use

1. DESCRIPTION

The OCV1A control unit is capable of commanding a motor (or a set of motors) by means of peripheral control units or

additional modules, depending on the wind conditions. The command will be implemented by making use of a switch to

be connected to the control unit.

2. PACKAGE CONTENTS

1 Electronic control unit on a sealed container (IP55)

2 Wind gauge inclusive of cable (length. 2 m)

3 Container wall-mounted support kit

4 Wind gauge supporting bracket

3. COMPATIBILITY

The OCV1A control unit is compatible with:

- a motor;

- an motor’s additional module;

- a peripheral control unit.

4. OPERATION

The OCV1A control unit operates by means of a switch which is connected to the control unit by means of terminals 3

(downward movement – the curtain will open), 4 (common push-button) and 5 (upward movement – the curtain

will close). The switch may be of the stable or push-button type.

In case a wind alarm occurs (wind gauge coming into action) when a stable switch has been left depressed in the

downward movement, the OCV1A control unit will in any case cause the curtain to go up, yet the curtain will go down

again 8 minutes after the alarm is triggered.

CAUTION!

When the alarm is ON, the switch will be fully disabled.

4.1 Operation priority

In the event that several commands are given simultaneously (e.g. curtain opening and wind alarm as well), the priority

will be as follows:

1 wind gauge; 2 switch.

4.2 Adjustments

The wind actuation threshold can be adjusted by means of a

potentiometer available on the board.

The “+” sign corresponds to 35 km/h; the “–“ sign corresponds to 1 km/h.

4.3 Installation reset

Upon the first installation, after checking the wind alarm for perfect operation, if the wind gauge is made to turn, the

curtain shall go up when the alarm speed is reached. You may cancel the alarm wait time (8 minutes) by pressing the

Reset button.

4.4 Connection diagrams

To control an electro-mechanical motor, fully adhere to the instructions given in Diagram 1.

Note: Connect a wire between terminals 2 (power supply input) and 7.

The motor common cable shall be connected to terminal 1 (power supply).

R19,5

R67

51 mm

31 mm

95 mm

FANTINI COSMI S.p.A.: VIA DELL’OSIO 6 20090 CALEPPIO DI

SETTALA MI

Tel. 02956821 fax 0295307006 E-mail: info@fantinicosmi.it

Technical assistance: supportotecnico@fantinicosmi.it

Connection diagram for one motor Diagram 1

Motor common BUS LINE

5. Commissioning instructions

The OCV1A control unit can be positioned in covered or uncovered civil premises in accordance with the rules and

regulations currently in force for the 230 V switching devices featuring a degree of protection equal to IP55.

How to install the container and the wind gauge

1 Place the OCV1A control unit, near the motor (if possible) or at any other suitable place. Two wall-mounted

supports are available to carry out this operation.

2 Remove the four screws, then make the connection to the board – make sure that every operation has been

carried out correctly prior to applying the voltage.

3 After powering the control unit, place the curtain at the half-travel position, then cause the wind gauge to turn and

verify that the curtain will go up (i.e. close) when the alarm has been triggered. In case the curtain moves in the

opposite direction, reverse the wires at terminals 6 and 8.

4 Secure the wind gauge to the special bracket available and verify that the gauge has been placed in such a perfect

position as to be hit by the wind.

5 Make the wind calibration, then close the cover and tighten down the screws again.

6 The cable inlet shall be positioned at the container bottom.

6. Technical features

Power supply 230 V – 50 Hz a.c.

Working temperature –10° ÷ +60°C

Relay max. capacity 250 Vac – 4 A (cosφ 0.4)

Wind calibration range 1 km/h ÷ 35 km/h

Container material ABS

“ colour Grey

“ dimensions 120 x 80 x 50

Produkt Specifikationer

Mærke:	Fantini Cosmi
Kategori:	Ikke kategoriseret
Model:	OCV1A

Har du brug for hjælp?

Hvis du har brug for hjælp til Fantini Cosmi OCV1A stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Fantini Cosmi Manualer

Fantini Cosmi B12MN Manual

21 Juni 2025

Fantini Cosmi K15A Manual

21 Juni 2025

Fantini Cosmi B01 Manual

21 Juni 2025

Fantini Cosmi A96 Manual

21 Juni 2025

Fantini Cosmi OCV1A Manual

21 Juni 2025

Fantini Cosmi O70RL Manual

16 Juni 2025

Fantini Cosmi S86 Manual

31 Marts 2025

Fantini Cosmi FF71A Manual

31 Marts 2025

Fantini Cosmi FF84 Manual

31 Marts 2025

Fantini Cosmi O42NCMAUX Manual

31 Marts 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

MSW -DA-11 Manual

21 Juni 2025

Foster FlexDrawer FFC2-1 Manual

21 Juni 2025

Westinghouse WHTT20V Manual

21 Juni 2025

Samsung AR18HSFSEWKNMG Manual

21 Juni 2025

Hoffman P2DO208 Manual

21 Juni 2025

Posiflex Gen9 Base Manual

21 Juni 2025

Universal Audio 1176LN Manual

21 Juni 2025

Weller WLIWBK2512A Manual

21 Juni 2025

Rane Zonetech Manual

21 Juni 2025

RGV Bollitore Digitale Manual

21 Juni 2025