Futaba SBD-2 Manual

Futaba Radiostyret legetøj SBD-2

Læs gratis den danske manual til Futaba SBD-2 (2 sider) i kategorien Radiostyret legetøj. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Futaba SBD-2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

S.BUS Decoder

SBD-2

Connection

Channel selection

*You should use an EXT battery, when using

many servos.

*If S.BUS/S.BUS2 servo

is connected to SBD-2,

CH written in S.BUS/

S.B US2 servo will

ignore. S.BUS/S.BUS2

servo is operated by

CH of SBD-2.

Mini screwdriver used

* #0 of rotary switch

position does not

use it.

* DG1, D G2 : Swi t c h chan n el ou t p u t

connector

Conventional servos（other than S.BUS servo）

● Eight servos are connectable.

● SBD-2 can change the output

CH by rotary switch.

External battery

(For servos)

Ext battery switch

C o n n e c t th e sho rt i n g p i n s

supplied when power is shared

with the receiver power source.

SBD-2

S.BUS / S.BUS2

Receiver

To S.BUS / S.BUS2

port

Rotary switch position

1 2 3 4 5 6 7 8 9

1 CH1 CH9 CH8 CH4 CH9 CH9 CH8 CH4 CH1

2 CH2 CH10 CH9 CH5 CH10 CH10 CH9 CH5 CH2

3 CH3 CH11 CH10 CH6 CH11 CH11 CH10 CH6 CH3

4 CH4 CH12 CH11 CH7 CH12 CH12 CH11 CH7 CH4

5 CH5 CH13 CH12 CH8 CH13 CH13 CH12 CH8 CH5

6 CH6 CH14 CH13 CH9 CH14 CH14 CH13 CH9 CH6

7 CH7 CH15 CH14 CH10 CH15 DG1 DG1 DG1 DG1

8 CH8 CH16 CH15 CH11 DG1 DG2 DG2 DG2 DG2

Servo output connectors

SBD-2 LED state

OFF OFF

S.BUS receive

error Blink

S. BUS

reception ON

Always use in the state in which the SBD-2 is

firmly attached to the fuselage of the airplane or

helicopter.

■ There is the danger of loss of control and crashing

if the connector is disconnected by vibration and

shock.

When using analog servos, always use in the state

in which the receiver is normal mode.

■ There is the danger of erroneous operation or

damage on the FASST12ch / High-speed mode.

Do not connect an S.BUS/S.BUS2 connector of the

SBD-2 to other than an S.BUS/S.BUS2 connection port.

■ There is the danger of erroneous operation or

damage.

Do not use the SBD-2 with anything other than an

R/C model.

To ensure that the SBD-2 is functioning as desired,

please test accordingly.

■ Do not y until inspection is complete.

Do not connect shorting pins, when using an Ext

battery.

■ There is the danger of explosion and ignition.

Ensure that the unit is mounted in an area that will

eliminate exposure to fuel, water and vibration.

■ As with any electronic components, proper

precautions are urged to prolong the life and

increase the performance of the SBD-2.

Allow a slight amount of slack in the SBD-2 cables

and fasten them Eat a suitable location to prevent

any damage from vibration during ight.

Do not connect either

a switch or battery in

this manner.

■ When a connector

is inserted like the

left, it short-circuits

and there is danger

of e x p lo s i o n an d

ignition.

WARNNG

INSTRUCTION MANUAL

Before using your new SBD-2, please read this manual

thoroughly and use the system properly and safely.

After reading this manual, store it in a safe place.

Thank you for purchasing an SBD-2, S.BUS decoder. The

SBD-2 is a converter for using conventional servos (other

than S.BUS servo) with the S.BUS/S.BUS2

system. The

SBD-2 connects to the receiver output of a S.BUS/S.BUS2

system and eight servos can be used.

SBD-2 can change the output CH from 9 groups select by

rotary switch. SBD-2 can use EXT battery (for servos).

Applicable receiver: S.BUS/S.BUS2

system receiver only

Usage Precautions

Connections and Name of Each Part of the SBD-2

Futaba Corp. will not be responsible for damage

caused by combination with other than Futaba

Genuine parts.

Input connector

●C o n n e c t s  t o t h e S . B U S /

S.BUS2 port of the receiver.

Rotary switch

Servo output connectors (1~8)

●Connecttheservos.

External battery

connector

(EXT.BATT)

●Connect the shorting pins

supplied when power is

shared with the receiver

power source.

Mini screwdriver

Monitor LED

manual are subject to change without prior notice. While this manual has been carefully written, there may be inadvertent

errors or omissions. Please contact our service center if you feel that any corrections or clariﬁcations should be made.

FUTABA CORPORATION Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba 299-4395, Japan

©FUTABA CORPORATION 2014, 8 (1)

[SBD-2 Ratings]

• Dimensions:

29.6mm x 39.3mm x 15.8mm

(1.17in. x 1.55in. x 0.62in.)

(excluding protruding)

• Weight:

14.2g (0.5 oz.)

• Power requirement:

4.8V ～7.4V

Monitor LED

Produkt Specifikationer

Mærke:	Futaba
Kategori:	Radiostyret legetøj
Model:	SBD-2

Har du brug for hjælp?

Hvis du har brug for hjælp til Futaba SBD-2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Radiostyret legetøj Futaba Manualer

Futaba R7208SB Manual

16 Juli 2025

16 Juli 2025

8 Juli 2025

8 Juli 2025

8 Juli 2025

Futaba R7214SB Manual

5 Februar 2025

Futaba GY470 Manual

5 Februar 2025

Futaba GYA553 Manual

5 Februar 2025

Futaba SBS-01RO Manual

15 Januar 2025

Futaba 12Z Manual

3 Oktober 2024

Radiostyret legetøj Manualer

Nyeste Radiostyret legetøj Manualer

Axial SCX30 Ford Bronco Manual

29 Oktober 2025

Proline Trencher LP 3.8 Manual

27 Oktober 2025

Proline Sand Paw LP Manual

26 Oktober 2025

Hobbywing XeRun V10 G2-4.5T Manual

29 September 2025

Hobbywing XeRun V10 G2-7.5T Manual

28 September 2025

Hobbywing EzRun-3652SL Manual

28 September 2025

Revell Glowee 2.0 Beast Manual

27 September 2025

Revell Quatcopter Nano Pocket Manual

27 September 2025

Blade 230 S Smart Manual

23 September 2025

Losi Mini LMT Manual

15 September 2025