Heatit HEAE5430499 Manual

Heatit Termostat HEAE5430499

Læs gratis den danske manual til Heatit HEAE5430499 (4 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 15 anmeldelser. Har du et spørgsmål om Heatit HEAE5430499, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Ver 2016-B

IMPORTANT!

PLEASE READ THIS BEFORE INSTALLATION.

This thermostat is tested and certiﬁed by Pepper One Gmbh

according to the requirements put forward by the Z-Wave

Alliance. This is a Z-wave Plus product with the 500 series chip.

If the product does not work with your gateway, then the

gateway manufacturer has not made an integration or

implemented such a thermostat with their gateway.

We do not give any guarantee towards integration.

PRINCIPLES FOR REGULATION

The Heatit Z-Wave thermostat is designed for controlling

electrical heating cables and electrical radiators/convectors.

The thermostat has 2 internal temperature sensors and has

3 algorithms for temperature compensation. After you have

set the temperature, the thermostat will use a hysteresis to

regulate the temperature. The hysteresis is adjustable.

TEMPERATURE SHOWN IN DISPLAY

The temperature shown in the display is the actual temperature

for ﬂoor sensor and the external room sensor. You are able to

calibrate the sensor values.

When using the internal room sensor, the temperature shown

is the set point. When using the internal sensor, the thermostat

can seem somewhat inaccurate. This is due to heat generation

inside the thermostat, draft and other external inﬂuences.

If the thermostat is to be used with waterbased heating systems,

you have to use an external sensor.

SETUP

This manual describes the most essential functions and

technical speciﬁcations of the thermostat. These instructions

help the user to control the thermostat, and the electrician

to install and setup the thermostat.

INSTALLATION

Installation must be done by a qualiﬁed electrical installer in

accordance with the National Building codes. Before installation,

disconnect any power to the thermostat’s mains. During

installation of the thermostat, power to the thermostat must

be disconnected AT ALL TIMES!

Use e.g. a small slotted screwdriver. Start by carefully removing

the front cover by pushing the release springs. The front cover

and the frame can now be removed.

Now connect the wires to the thermostat’s terminals:

HEATING (N) Heating cable connection (Neutral)

N Power connection (Neutral) 230V

L Power connection (Live) 230V

HEATING (L) Heating cable connection (Live)

PILOT Pilot signal (ECO temp) 230V

FLOOR SENSOR NTC type (10, 12, 15, 22, 33 or 47kΩ).

Default 10kΩ.

EXTERNAL SENSOR NTC type (10, 12, 15, 22, 33 or 47kΩ).

Default 10kΩ.

Next, position the thermostat and fasten it onto the wall’s

mounting box using 2-4 screws. Position the frame, then

position and carefully press the front cover until it snaps in

place. Check that the front cover has snapped in place properly

on both left and right side. The front cover should now be ﬁrmly

ﬁxed on all sides.

STARTUP

AFTER CONNECTING THE POWER TO THE THERMOSTAT FOR THE

FIRST TIME, ALL PARAMETERS WILL HAVE DEFAULT SETTINGS.

2 yr

HEATIT Z-WAVE

Installers manual

Firmware 1.8

01.06.2016

Release spring

1: Left 3: Right2: Center

87 mm

58,8 mm

HEAT ING L

HEAT ING N

PILOT WIRE

FLOOR

SENSOR

EXT ERNAL

SENSOR

Made in EU

TF 021

21,3 mm

51,1 mm

87 mm

58,8 mm

29,9 mm

Produkt Specifikationer

Mærke:	Heatit
Kategori:	Termostat
Model:	HEAE5430499
Kode for international beskyttelse (IP):	IP21
Dybde:	51.1 mm
Produktfarve:	Hvid
Strøm:	16 A
Skærm:	LCD
Fjernbetjening inkluderet:	Ingen
Strømkilde:	Vekselstrøm
Certificering:	CE
Grænseflade:	Z-Wave
Driftsspænding:	230 V
Temperaturinterval (T-T):	5 - 40 °C
Hukommelsesfunktion:	Ingen
Måleenhed:	°C
Frekvens:	868.42 MHz
Maksimal koblingsstrøm:	16 A
Temperatur sætpunktsinterval:	5 - 40 °C
Maksimal skiftekapacitet:	3600 W
Temperaturkontrol interval:	0 - 25 °C