Heatit Z-Temp3 Manual

Heatit Termostat Z-Temp3

Læs gratis den danske manual til Heatit Z-Temp3 (8 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 47 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 24 anmeldelser. Har du et spørgsmål om Heatit Z-Temp3, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
1. INTRODUCTION
Heatit Z-Temp3 is a battery-operated thermostat designed for
controlling waterbased heating systems. Used in combination
with the Heatit Z-Water2, you can control your heating system
through the Z-Wave
®
network or via the buttons on the front
panel. The thermostat has a user-friendly interface.
The thermostat fits into System 55 frames, and may be
mounted alongside other equipment such as e.g dimmers or
light switches. Heatit Z-Temp3 can also be mounted directly
on the wall or placed freely, e.g. on a shelf.
Heatit Z-Temp3 can be set as a master thermostat. This means
that you can set the setpoint and mode on one unit, and it will
automatically send the setpoint and mode to other connected
units.
All communication between Heatit Z-Temp3 and the
controlled device is 100% wireless.
Heatit Z-Temp3 uses 2x AAA batteries, but you can also
connect the device to an external power source. The
Heatit Transformer 230VAC (45 126 48) is recommended for
this purpose.
Heatit Z-Temp3 can be associated with Heatit ZM Single Relay,
other Z-Wave relays, Heatit ZM Thermostat, Heatit Z-TRM6
Thermostat and other Z-Wave devices to control other types
of heating solutions.
Heatit Z-Temp3 is a great choice for the restoration or
renovation of existing buildings, as it is easy to install without
the need for wiring. We recommend using multiple 230VAC
devices to create a mesh network.
2. STATEMENT REGARDING PRODUCTS FROM MULTIPLE
MANUFACTURERS
Please read this before installation
This device may be used with all devices certified with the
Z-Wave Plus
®
certificate and should be compatible with
such devices produced by any manufacturer. Every primary
controller is dierent depending on the manufacturer, their
target audience and intended use/application. Please review
the functionalities implemented by the primary controller you
intend to use with our Z-Wave Plus certified device to ensure
that it provides the necessary controls to take full advantage of
our product’s capabilities.
3. BEHAVIOR WITHIN THE Z-WAVE NETWORK
This device may be operated within any Z-Wave
®
network
with Z-Wave-certified devices from other manufacturers. All
non-battery-operated nodes within the network will act as
repeaters regardless of manufacturer to increase the reliability
of the network. On delivery, the device does not belong to any
Z-Wave network. The device needs to be added to an existing
network to communicate with the other devices within it.
Devices may also be removed from a network. The add/
remove processes are initiated by the primary controller of the
Z-Wave network.
PRODUCT
DOCUMENTS
HEATIT
Z-TEMP3
Installers manual
Firmware version Document version
FW 1.0 2024-D
Article no. Document date
45 126 90
45 126 91
15.09.2024
Org. doc. date 01.07.2024
White RAL 9003 Black Matt
45 126 90 45 126 91
TABLE OF CONTENTS
1. Introduction
2. Statement regarding
products from multiple
manufacturers
3. Behavior within the
Z-Wave network
4. Quick Start
5. Connections
6. Installation
7. Add/Remove
8. Factory Reset
9. Startup
10. Principles of regulation
11. Local settings menu
12. Display Menu structure
13. Temperature shown in
display
14. Standby and main screen
15. Calibration
16. Brightness
17. Display on/o
18. Display icons
19. Child lock
20. Open window detection
21. Error codes
22. QR-Code Placement (DSK)
23. Security
24. Node Information Frame
25. Associations
26. Association Groups
27. Configuration Parameters
28. Command Classes
29. Supported Command
Classes
30. Controlled command
classes
31. Disclaimer
32. Thermostat dimensions
33. Thermostat controls
34. Order of assembly
35. Chart - Display Menu
Product info
4. QUICK START
1. Insert the batteries or alternatively connect the cable
supplied with the Heatit Transformer 230VAC
(Art. no. 45 126 48).
2. Mount the device directly on the wall or on a junction box.
3. If using a power supply instead of batteris, Connect the wires
according to the description in Chapter ”Connections”.
Turn on the voltage.
4. Set the primary controller in add mode (security/non-
security).
5. Hold the Center button until “OFF” is shown in the display
(approx. 5 seconds).
6. Press the ”+” button once to reach “CON”, and hold the
middle button “ “ until the display shows a rotating pattern.
7. The thermostat will display “INCL” when the thermostat is
successfully added.
NB! If adding/removing fails, Err (error) will appear.
5. CONNECTIONS
The Heatit Z-Temp3 can be connected to a 2.7 to 3.3VDC
power supply via the optional cable, providing an alternative
to using batteries. The cable is supplied with the Heatit
Transformer 230VAC (Art. no. 45 126 48).
To access the batteries and power connector, or to mount the
device, hold the sides of the display and gently pull outwards
to detach the thermostat from the mounting plate.
Red cable 3VDC
Black cable 0VDC
6. INSTALLATION
Remove the thermostat from the frame and mounting plate.
Insert the 2x AAA batteries in the thermostat or connect
the connector on the back using the optional cable. The
thermostat oers versatile installation options, allowing it to be
mounted on a wall, on a junction box or placed at a preferred
location. For wall mounting, attach the mounting plate using
either screws or double-sided tape. If mounting on a junction
box, use screws. Once the mounting plate is in place, carefully
push the thermostat back onto the mounting plate.
NB! Be careful when installing the batteries, ensuring their
polarity matches the indented markings on the plastic.
7. ADD/REMOVE
Please read this before installation
The primary controller/gateway has a mode for adding or
removing devices. Please refer to your primary controller
manual on how to set the primary controller in add/remove
mode. The device may only be added or removed from the
network if the primary controller is in add/remove mode.
When the device is removed from the network, it will NOT
revert to factory settings.
Adding the device within a 2 meter range from the gateway
can minimize faults during the Interview process.
Note: The Heatit Z-Temp3 does not stay in Learn mode until it
is included.
There are two ways to add the device to a Z-Wave network.
7.1 Method 1: Standard (Manual)
Add/remove mode is indicated on the device by rotating
LCD segments on the display. It indicates this for 90 seconds
until a timeout occurs, or until the device has been added to/
removed from the network. Configuration mode can also be
cancelled by performing the same procedure used for starting
Configuration mode.
1. Hold the Center button for 5 seconds.
The display will show “OFF”.
2. Press the ”+” button once to see “CON” in the display.
3. Start the add/remove device process in your primary
controller.
4. Start the configuration mode on the thermostat by holding
the Center button for approximately 2 seconds.
The device is now ready for use with default settings.
NB! When the device is removed from the gateway, the
parameters are not reset. To reset the parameters, see Chapter
”Factory reset”.
If inclusion fails, please perform a ”remove device” process and
try again. If inclusion fails again, please see “Factory reset”.
7.2 Method 2: SmartStart (Automatic)
SmartStart enabled products may be added to a Z-Wave
network by scanning the Z-Wave QR-Code on the product
if your primary controller supports SmartStart inclusion. No
further action is required and the SmartStart product will be
added automatically after being powered on within range of
the primary controller.
8. FACTORY RESET
Enter the menu by holding the Center button for about 5
seconds, navigate in the menu with the ”+” button til you see
FACT. Press the Center button until you see “-- --” blinking in
the display, then hold for about 5 seconds to perform a reset.
You may also initiate a reset by holding the Right and Center
buttons for 55 seconds.
When either of these procedures has been performed, the
thermostat will perform a complete factory reset. The device
will display “RES” for 5 seconds while performing a factory
reset. When “RES” is no longer displayed, the thermostat has
been reset.
Please use this procedure only when the primary controller is
missing or otherwise inoperable.
9. STARTUP
After powering up the device for the first time, all parameters
will have default settings.

Produkt Specifikationer

Mærke: Heatit
Kategori: Termostat
Model: Z-Temp3

Har du brug for hjælp?

Hvis du har brug for hjælp til Heatit Z-Temp3 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Termostat Heatit Manualer

Heatit

Heatit S-Control2 Manual

19 August 2025
Heatit

Heatit Z-Temp3 Manual

3 Januar 2025
Heatit

Heatit PRO Manual

24 September 2024
Heatit

Heatit MULTIREG6 Manual

24 September 2024
Heatit

Heatit WiFi6 Manual

17 Juli 2024
Heatit

Heatit Z-TRM6 DC Manual

17 Juli 2024
Heatit

Heatit WiFi Manual

17 Juli 2024
Heatit

Heatit External Room Sensor Manual

17 Juli 2024
Heatit

Heatit ZM Manual

16 Juli 2024
Heatit

Heatit Z-TRM6 Manual

16 Juli 2024

Termostat Manualer

Nyeste Termostat Manualer

UPM

UPM HTM311A Manual

12 Oktober 2025
Bticino

Bticino NT4451 Manual

8 Oktober 2025
Bticino

Bticino HS4451 Manual

7 Oktober 2025
Bticino

Bticino N4451 Manual

7 Oktober 2025
Bticino

Bticino L4451 Manual

7 Oktober 2025
Bticino

Bticino AM5721 Manual

6 Oktober 2025
Bticino

Bticino L4441FH Manual

6 Oktober 2025
Bticino

Bticino Living 4477 Manual

6 Oktober 2025
Bticino

Bticino HC4451 Manual

6 Oktober 2025
Emerson

Emerson ST75 Manual

1 Oktober 2025