Heatit Zig Dim Manual

Heatit Ikke kategoriseret Zig Dim

Læs gratis den danske manual til Heatit Zig Dim (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 58 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 29.5 anmeldelser. Har du et spørgsmål om Heatit Zig Dim, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

We have designed this product in accordance with our strict quality requirements

(ISO 9001) and environmental requirements (ISO 14001). All electrical installations

must be carried out by an authorized electrical installer. The product must be

installed in accordance with our installers manual and national building codes.

Any wrongful installation, misuse or damage to the product, is not covered under

warranty.

Heatit Controls AB can not be held liable for any type of errors or omittances in our

product information. Product speciﬁcations may change without further notice.

Heatit Controls AB l Läkarvägen 4, 454 31 BRASTAD, SWEDEN

Phone: +47 61 18 77 77 l post@heatit.com – www.heatit.com

MOUNTING

WIRING DIAGRAM

Max tightening torque terminal screws: 2Nm.

INSTALLATION AND WIRING

1. Switch oﬀ the mains voltage (turn oﬀ the fuse).

2. Open the junction box.

3. Connect according to the wiring diagram as shown above:

• Connect the Live to the dimmer terminal marked ”L”.

• Connect the load terminal marked ”L” to the dimmer

terminal marked

4. Install the dimmer (A) in the wall box. Make sure that no

wires are pinched.

5. Attach the cover (B) with the supplied nut (C).

6. Attach the button (D) with a simple push.

7. After verifying the connections, switch on the mains voltage.

8. Set the primary controller in add mode.

9. Press the reset button on the dimmer 3 times in a rapid

sequence. Heatit Zig Dim is now included in your network.

ADD/REMOVE

The primary controller/gateway has a mode for adding or

removing devices. Please refer to your primary controller

manual on how to set the primary controller in add/remove

mode. The device may only be added or removed from the

network if the primary controller is in add/remove mode.

A B B C D

FEATURES

• • Zigbee rotary dimmer Short circuit protection

• • 2-wire Surge protection

• • 5W - 250W LED Overheat protection

• • Rotary and push dimming External momentary switch

• • Nemko certied Min. dim level adjustable

• • Trailing edge Max dim level auto-calibration

• Overload protection

TECHNICAL DATA

Protocol Zigbee, 2.4GHz

Chip Zigbee 3.0

Rated voltage 230VAC 50Hz

Power 5W - 250W

Controls Rotary and push dimming

Ambient temperature 5°C to 40°C

Storage temperature 5°C to 40°C

Range RF Min. 40 meter

Flush mounting depth 24mm

Screw terminals Max. 2.5mm² 2Nm

IP Code IP21

Size (LxWxH) 84 x 84 x 43mm

Approvals CE, Nemko

Working frequency 2.4GHz, Max output power 19,8dBm.

The distance between user and products should be no less

than 20 cm.

MAINTENANCE

The device is maintenance-free.

Indoor use only.

INTRODUCTION

Heatit Zig Dim is a Zigbee rotary dimmer for many diﬀerent

types of light ﬁxtures. The dimmer works on most low loads

without causing ﬂickering. Heatit Zig Dim is very well suited for

LED.

The dimmer is equipped with an external momentary switch

option. This allows you to dim and turn on/oﬀ the light.

The dimmer ﬁts in European wall boxes and can be used with

most frames that are adapted to System 55.

When connecting low loads it is recommended to use a bypass.

NB! Dimming may be challenging, and we recommend

checking the compatibility of diﬀerent light sources before

installation.

INSTALLATION

Installation must be done by a qualiﬁed electrician in

accordance with national building codes. Before installation,

disconnect the power to the device from the mains. During

installation of the device, power to the device must be

disconnected AT ALL TIMES!

Quick Guide

HEATIT

ZIG DIM 250W

Article no. Doc. version Doc. date

14 444 20 2023-A 01.06.2023

Inclusion to a Zigbee network

1. Remove the device from any previous

Zigbee network that it may have been added

to, otherwise pairing mode will fail.

2. Set the primary controller to add mode.

3. To start the conﬁguration process, press the Reset button

or the external switch connected to P, 3 times in rapid

succession.

4. The device LED will blink in green when the adding

procedure has been successfully initiated.

Removing from a Zigbee network

Removing a device from the Zigbee Network is initiated from

the gateway. Check your gateway manual on how to remove

a device.

Performing a factory reset

Press and hold the Reset button. After 3 seconds the LED will

start to blink green. After 20 seconds the LED will stop blinking

and emit a constant light. You may now release the button.

Figure 1 (success)

Within the 3 second period the button must be released. If the

button is released within this period, the device will reset and

start blinking red because it is not included in a gateway.

0s 1s

0,5s

2s 3s 4s 5s 19s 20s 0,5s 1,5s 2,5s

1s 2s 3s 1s 2s 3s

Figure 2 (fail)

If the button is released before the 3 second period, the device

will indicate fail by turning RED LED on for 3 seconds.

Figure 3 (fail)

The button MUST be released between 20 and 23 seconds for

local reset to take place. If held longer, the device will ignore

the command.

0s 1s

0,5s 2s 3s xs x+3s

Successful

Unsuccessful

0s 1s

0,5s 2s 3s 4s 5s

3<x<20s

Released @ x seconds

6<x+3<23s

0s 1s

0,5s 2s 3s 4s 5s 19s 20s 21s 22s 23s 24s20,5s 21,5s 22,5s

White RAL 9003

14 444 20

TOUCHLINK

1. Press the reset button 4 times.

2. The device LED will blink blue when it is ready to be paired.

3. Bring the remote within 10 cm of the dimmer and set the

remote to TouchLink pairing.

4. If the procedure was successful, the LED will light up in

solid green for 3 seconds.

0s 1s

0,5s 2s 3s xs x+3s

Successful

Unsuccessful

Note:

• When neither device (dimmer and remote) are included in a

Zigbee network, each dimmer can only link to one remote.

• When both devices are included in the same Zigbee network,

each dimmer can link with max. 30 remotes.

• For Philips Hue Hubs and Amazon Echo Plus, add remote

and device to network ﬁrst, then TouchLink.

FIND AND BIND

1. Press the reset button 5 times.

2. The device LED will blink yellow when it is ready to be

added.

3. Set the remote into Find and Bind mode and enable

Find and Bind pairing. Please refer to the manufacturer

instructions on how to do this.

4. There should be an indication on the remote that it has

successfully connected to the dimmer, and can control it.

0s 1s

0,5s

2s 3s xs x+3s

Successful

Unsuccessful

CONTROLS

MEASUREMENTS AND DRAWINGS

71mm

50mm

16,7mm

23,5mm

TO PRODUCT

DOCUMENTS

Org. doc. 01.06.2023

Produkt Specifikationer

Mærke:	Heatit
Kategori:	Ikke kategoriseret
Model:	Zig Dim

Har du brug for hjælp?

Hvis du har brug for hjælp til Heatit Zig Dim stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Heatit Manualer

Heatit Multireg IceControl Pro Manual

23 December 2025

Heatit Z-WATER2 Manual

17 Juli 2024

Heatit Leakage Stopper Manual

17 Juli 2024

Heatit Transformer Manual

17 Juli 2024

Heatit Zig Dim Manual

16 Juli 2024

Heatit Z-Dim2 Manual

16 Juli 2024

Heatit Z-RELAY Manual

16 Juli 2024

Heatit Z-DIN 616 Manual

16 Juli 2024

Heatit Z-Gateway Manual

16 Juli 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vonroc CD839AA Manual

29 December 2026

WAC Lighting L-1052 Manual

29 December 2026

ProSelect PSTSP21AWH Manual

29 December 2026

TOTO TS300A51 Manual

29 December 2026

WAC Lighting LTK-720 Manual

29 December 2026

WAC Lighting H-2020 Manual

29 December 2026

Electro Harmonix 720 Manual

29 December 2026

Nokia Comfort Earbuds TWS-411 Manual

29 December 2026

Duravit L-Cube LC624007272 Manual

29 December 2026

WAC Lighting BA-ACLED36 Manual

29 December 2026