Heatit Z-DIN 616 Manual

Heatit Ikke kategoriseret Z-DIN 616

Læs gratis den danske manual til Heatit Z-DIN 616 (12 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Heatit Z-DIN 616, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/12

TABLE OF CONTENTS

1 Introduction

2 Behavior within the Z-Wave network

3 Installation

3.1 Relay outputs

3.2 Inputs

4 Factory reset

5 Adding the Heatit Z-DIN 616 to the Z-Wave network

6 Associations

6.1 Association groups

7 Conﬁguration parameters

8 Command classes

8.1 Supported command classes

8.2 Controlled command classes

9 Technical documentation

HEATIT

Z-DIN 616 Ver 2021-A

Firmware 0.15

01.02.2021

Installers manual

1. INTRODUCTION

The Heatit Z-DIN 616, which is built upon the wireless Z-Wave

communication protocol, has 6 relay driven outputs and 6 digital

inputs. The unit is a multi-purpose Z-Wave I/O module, which can be

used for many applications. For example, the Heatit Z-DIN 616 provides

the possibility to control other systems via the Z-Wave network, by

utilizing the 6 outputs as a kind of hand-over function to another

automation system.

The relay outputs (controlled through the Z-Wave network) are suitable

for switching up to six 230VAC loads. In connection with simultaneous

connection to SELV (Safety Extra Low Voltage) and 230VAC power

circuits for relay outputs, relays must be considered as two groups,

where the ﬁrst group includes output 1 to 3 and the second group

includes outputs 4 to 6. This ensures complete separation between

the SELV and 230VAC circuits. If one of the relays in the group is

connected to a SELV circuit, the remaining outputs are not allowed to

be connected to 230VAC or another circuit which is not a SELV circuit.

For example, the relay outputs of the Heatit Z-DIN 616 module can be

used to control the 230Vac power supply outlet, making it possible

to turn on and disconnect the electrical outlets directly through the

Z-Wave network. For safety reasons, however, it is not recommended

to use the Heatit Z-DIN 616 to connect electrical outlets that are

normally used for hazardous tools and machinery.

The 6 digital inputs of the Heatit Z-DIN 616 are useful for various

purposes, where potential-free contacts or Open Collector outputs

may be connected. The inputs may be conﬁgured to diﬀerent trigger

modes; leading edge, trailing edge or level triggered. The Heatit Z-DIN

616’s inputs may be programmed to control other Z-Wave devices

when the inputs are activated, by sending Z-Wave commands over the

Z-Wave network to e.g. Z-Wave relay modules, dimmer units etc.

Heatit Z-DIN 616 allows sending diﬀerent types of Z-Wave commands

by utilizing the diﬀerent association groups for the 6 inputs. In addition,

the Heatit Z-DIN 616 also acts as a repeater, thus extending the range

of the Z-Wave network. By default, the Heatit Z-DIN 616’s inputs and

outputs are set to operate as toggle-relays. Input 1 controls the output

1, input 2 controls the output 2, etc. This functionality can be modiﬁed

via the conﬁguration parameters 3-8 and 13-18.

2. BEHAVIOR WITHIN THE Z-WAVE™ NETWORK

This device may be operated within any Z-Wave network with

Z-Wave-certiﬁed devices from other manufacturers. All non-battery-

operated nodes within the network will act as repeaters regardless of

manufacturer to increase the reliability of the network. On delivery, the

device does not belong to any Z-Wave network.

The device needs to be added to an existing network to communicate

with the other devices within it. Devices may also be removed from

a network. The add/remove processes are initiated by the primary

controller of the Z-Wave network.

Produkt Specifikationer

Mærke:	Heatit
Kategori:	Ikke kategoriseret
Model:	Z-DIN 616
Produktfarve:	Grå
Strømforbrug (typisk):	0.6 W
Dimensioner (BxDxH):	105 x 60 x 85 mm
Maksimal indendørs rækkevidde:	40 m
Bæredygtighedscertifikater:	CE, RoHS
Overholdelse af bæredygtighed:	Ja
Antal poler:	1
DIN-skinne montering:	Ja
AC udgangsspænding:	250/360 V