Heatit Z-WATER2 Manual

Heatit Ikke kategoriseret Z-WATER2

Læs gratis den danske manual til Heatit Z-WATER2 (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Heatit Z-WATER2, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/5
1. INTRODUCTION
Heatit Z-Water2 is a DIN-rail regulator for controlling
waterbased heating systems. The module clips right onto a
DIN-rail and allows you to control your waterbased heating
through your Z-Wave™ network.
Heatit Z-Water2 is equipped with 9 potential free relays for
actuators. It also has 2 analog inputs for temperature sensors.
The Heatit Z-Water2 relays may be controlled by associations
with other Z-Wave thermostats e.g Heatit. Each relay can
control one or several actuators in your underfloor heating
system.
2. STATEMENT REGARDING PRODUCTS FROM MULTIPLE
MANUFACTURERS
Please read this before installation
This device may be used with all devices certified with the
Z-Wave Plus™ certificate and should be compatible with
such devices produced by any manufacturer. Every primary
controller is dierent depending on the manufacturer, their
target audience and intended use/application. Please review
the functionalities implemented by the primary controller you
intend to use with our Z-Wave Plus certified device to ensure
that it provides the necessary controls to take full advantage of
our product’s capabilities.
3. BEHAVIOR WITHIN THE Z-WAVE NETWORK
This device may be operated within any Z-Wave™ network
with Z-Wave-certified devices from other manufacturers. All
non-battery-operated nodes within the network will act as
repeaters regardless of manufacturer to increase the reliability
of the network. On delivery, the device does not belong to any
Z-Wave network. The device needs to be added to an existing
network to communicate with the other devices within it.
Devices may also be removed from a network. The add/
remove processes are initiated by the primary controller of the
Z-Wave network.
4. INSTALLATION GUIDELINES
Installation must be done by a qualified electrician in
accordance with national building codes. Before installation,
disconnect the power to the device from the mains. During
installation of the device, power to the device must be
disconnected AT ALL TIMES!
Max tightening torque for terminal screws: 2Nm
Use the following procedure to install Heatit Z-Water2:
1. Place the top part of the DIN rail mounting on the Heatit
Z-Water2 over the top of the DIN rail so it hooks onto the
rail.
2. Use a flathead screwdriver to push the DIN rail mounting tab
downward.
3. Tilt the bottom of the Heatit Z-Water2 until it touches the
DIN rail. Now let go of the DIN rail mounting tab so it locks
into place.
4. Make all the necessary connections to the device (max
tightening torque for all screw terminals is 2Nm). Apply
power to the device after all connections have been made.
TABLE OF CONTENTS
1. Introduction
2. Statement regarding products from multiple
manufacturers
3. Behaviour within the Z-Wave network
4. Installation guidelines
5. Connections
6. Quick Start
7. Add/Remove
7.1 Method 1: Standard (Manual)
7.2 Method 2: SmartStart (Automatic)
8. Factory Reset
9. Startup
10. LED blinking patterns description
11. QR-Code Placement (DSK)
12. Security
13. Node Information Frame
14. Associations
14.1 Setting and Removing Associations
15. Association Groups
16. Configuration Parameters
17. Calibration
18. Command Classes
18.1 Basic Command CLass
18.2 Binary Switch Command Class
18.3. Multilevel Sensor Command Class
18.4. Indicator Command Class
19. Supported Command Classes
20. Other features
21. Dimensions
22. External antenna connector
Product info
HEATIT
Z-WATER2
Installers manual
Firmware version Document version
FW 1.0 2023-A
Article no. Document date
45 124 95 01.05.2023
Org. doc. date 01.05.2023
TO PRODUCT
DOCUMENTS

Produkt Specifikationer

Mærke: Heatit
Kategori: Ikke kategoriseret
Model: Z-WATER2

Har du brug for hjælp?

Hvis du har brug for hjælp til Heatit Z-WATER2 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Heatit Manualer

Heatit

Heatit Multireg IceControl Pro Manual

23 December 2025
Heatit

Heatit Z-WATER2 Manual

17 Juli 2024
Heatit

Heatit Leakage Stopper Manual

17 Juli 2024
Heatit

Heatit Transformer Manual

17 Juli 2024
Heatit

Heatit Zig Dim Manual

16 Juli 2024
Heatit

Heatit Z-Dim2 Manual

16 Juli 2024
Heatit

Heatit Z-RELAY Manual

16 Juli 2024
Heatit

Heatit Z-DIN 616 Manual

16 Juli 2024
Heatit

Heatit Z-Gateway Manual

16 Juli 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vonroc

Vonroc CD839AA Manual

29 December 2026
WAC Lighting

WAC Lighting L-1052 Manual

29 December 2026
ProSelect

ProSelect PSTSP21AWH Manual

29 December 2026
TOTO

TOTO TS300A51 Manual

29 December 2026
WAC Lighting

WAC Lighting LTK-720 Manual

29 December 2026
WAC Lighting

WAC Lighting H-2020 Manual

29 December 2026
Electro Harmonix

Electro Harmonix 720 Manual

29 December 2026
Nokia

Nokia Comfort Earbuds TWS-411 Manual

29 December 2026
Duravit

Duravit L-Cube LC624007272 Manual

29 December 2026
WAC Lighting

WAC Lighting BA-ACLED36 Manual

29 December 2026