Heatit Z-Dim2 Manual

Heatit Ikke kategoriseret Z-Dim2

Læs gratis den danske manual til Heatit Z-Dim2 (15 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 105 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 53 anmeldelser. Har du et spørgsmål om Heatit Z-Dim2, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/15
1. INTRODUCTION
Heatit Z-Dim2 is a Z-Wave™ rotary dimmer for many dierent types
of light xtures. The Heatit Z-Dim2 works on most low loads without
causing ickering.
The dimmer is equipped with an external switch option. This allows
you to dim and turn on/o the load from an external switch.
Heatit Z-Dim2 is very well suited for LED, and ts into System 55 frames.
When connecting low loads it is recommended to use a bypass.
NB! DIMMING
Dimming may be challenging, and we recommend checking the
compatibility of dierent light sources before installation. We are
happy to answer any questions.
2. STATEMENT REGARDING PRODUCTS FROM MULTIPLE
MANUFACTURERS
Please read this before installation
This device may be used with all devices certied with the Z-Wave
Plus™ certicate and should be compatible with such devices
produced by any manufacturer. Every primary controller is dierent
depending on the manufacturer, their target audience and intended
use/application. Please review the functionalities implemented
by the primary controller you intend to use with our Z-Wave Plus
certied device to ensure that it provides the necessary controls to
take full advantage of our product’s capabilities.
3. BEHAVIOUR WITHIN THE Z-WAVE™ NETWORK
This device may be operated within any Z-Wave network with
Z-Wave-certied devices from other manufacturers. All non-battery-
operated nodes within the network will act as repeaters regardless of
manufacturer to increase the reliability of the network. On delivery,
the device does not belong to any Z-Wave network. The device needs
to be added to an existing network to communicate with the other
devices within it. Devices may also be removed from a network. The
add/remove processes are initiated by the primary controller of the
Z-Wave network.
4. QUICK START
1. Switch o the mains voltage (turn o the fuse).
2. Open the junction box.
3. Connect according to the wiring diagram as shown in chapter 7
“Installation & wiring”.
4. After verifying the connections, switch on the mains voltage.
5. Set the primary controller in add mode (security/non-security).
6. Press the reset button on dimmer 3 times in a rapid sequence.
Heatit Z-Dim2 is now included in your Z-Wave network.
HEATIT
Z-DIM2 250W Ver 2022-A
Firmware 1.20
01.05.2022
Installers manual
TABLE OF CONTENTS
1. Introduction
2. Statement regarding products from multiple manufacturers
3. Behaviour within the Z-Wave™ network
4. Quick Start
5. Control
6. Illustrations
7. Installation and wiring
8. External Switch
9. Add/Remove
9.1 Method 1: Standard (Manual)
9.2 Method 2: SmartStart (Automatic)
10. Factory Reset
11. Startup
12. LED blinking patterns description
13. QR-Code Placement (DSK)
14. Security
15. Node Information Frame
16. Associations
16.1 Setting and Removing Associations
17. Association Groups
18. Conguration Parameters
19. Autocalibration of maximum dim level
20. Command Classes
20.1 Basic Command Class
20.2 Multilevel Switch Command Class
20.3 Meter Command Class
20.4 Indicator Command Class
20.5 Central Scene Command Class
21. Supported Command Classes
Product info
White RAL 9003
plastic kit
White RAL 9010
plastic kit
Dimmer unit
Art.no. 14 444 40
5. CONTROL
Increase / decrease On / O
6. ILLUSTRATIONS
23,5mm 16,7mm71mm
50mm
51,5mm
71mm
7. INSTALLATION AND WIRING
Installation must be done by a qualied electrical installer in
accordance with the national building codes. Before installation,
disconnect any power to the dimmer mains. During the installation
process, the fuse must be turned o AT ALL TIMES!
NB! Max tightening torque for terminal screws: 2Nm
NB! This is a 2-wire dimmer so the Neutral is only connected to the
load and not the dimmer itself.
1. Turn o the fuse.
2. Connect the Live to the dimmer terminal marked ”L”.
3. Connect the load terminal marked ”L” to the dimmer terminal
marked
4. Install the dimmer (A) in the wall box.
Make sure that no wires are pinched.
5. Attach the cover (B) with the supplied
nut (C).
6. Attach the button (D) with a simple
push.
S1: Dimmer knob.
Can be used as a scene controller.
S2: External switch connected to P.
Used for either dimming or
scene controller.
8. EXTERNAL SWITCH
Momentary Switch (NO)
When using a momentary switch, the switch functionality can be
selected using Parameter 7.
The switch must be a normally open switch.
9. ADD/REMOVE
Please read this before installation
The primary controller/gateway has a mode for adding or removing
devices. Please refer to your primary controller manual on how to set
the primary controller in add/remove mode. The device may only be
added or removed from the network if the primary controller is in add/
remove mode. When the device is removed from the network, it will
NOT revert to factory settings.
There are two ways to add the device to a Z-Wave network.
9.1 Method 1: Standard (Manual)
Add/remove mode is indicated on the device by a blinking green LED.
It indicates this for 90 seconds until a timeout occurs, or until the
module has been added to/removed from the network.
To start the conguration process press the Reset
button, or the external switch connected to P,
3 times in rapid succession. The LED will blink green for
3 seconds if adding/removing is successful. The device
is now ready for use with default settings.
NB! When the device is removed from the gateway, the parameters are
not reset. To reset the parameters, see Chapter 10 ”Factory reset”.
If inclusion fails, please perform a ”remove device” process and try
again. If inclusion fails again, please see Chapter
10 “Factory reset”.
9.2 Method 2: SmartStart (Automatic)
SmartStart enabled products may be added to a Z-Wave network
by scanning the Z-Wave QR-Code on the product if your primary
controller supports SmartStart inclusion. No further action is required
and the SmartStart product will be added automatically after being
powered on within range of the primary controller.
10. FACTORY RESET
Please read this before installation
Press and hold the reset button. After 3 seconds the LED will start to blink in
green. After 20 seconds the LED will shine solid green for 3 seconds. You may
now release the button.
Please attempt exclusion before using factory reset.
11. STARTUP
After powering up the device for the rst time, all the parameters will have
default settings.
A B B C D
Wiring diagram
LL
L
N

Produkt Specifikationer

Mærke: Heatit
Kategori: Ikke kategoriseret
Model: Z-Dim2

Har du brug for hjælp?

Hvis du har brug for hjælp til Heatit Z-Dim2 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Heatit Manualer

Heatit

Heatit Z-WATER2 Manual

17 Juli 2024
Heatit

Heatit Leakage Stopper Manual

17 Juli 2024
Heatit

Heatit Transformer Manual

17 Juli 2024
Heatit

Heatit Zig Dim Manual

16 Juli 2024
Heatit

Heatit Z-Dim2 Manual

16 Juli 2024
Heatit

Heatit Z-RELAY Manual

16 Juli 2024
Heatit

Heatit Z-DIN 616 Manual

16 Juli 2024
Heatit

Heatit Z-Gateway Manual

16 Juli 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

GLORIA

GLORIA Prima 3 Manual

16 August 2025
Advantech

Advantech MIO-2364A-P2A1 Manual

16 August 2025
Aiwa

Aiwa IC-320DAB Manual

16 August 2025
Advantech

Advantech MIC-711-OX3A1 Manual

16 August 2025
Advantech

Advantech ARK-11-S1A3 Manual

16 August 2025
Mars Gaming

Mars Gaming MSRGB2 Manual

16 August 2025
MSW

MSW -WAX-C61150 Manual

16 August 2025
Advantech

Advantech ARK-1125H-S0A1 Manual

16 August 2025
Gossen Metrawatt

Gossen Metrawatt SYSKON P3000 Manual

16 August 2025
Advantech

Advantech IDAQ-821-AE Manual

16 August 2025