I-PRO WV-QSR504 Manual

I-PRO Ikke kategoriseret WV-QSR504

Læs gratis den danske manual til I-PRO WV-QSR504 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 8 anmeldelser. Har du et spørgsmål om I-PRO WV-QSR504, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Ns0522-1122

Printed in China

• Before attempting to connect or install this product, please read these instructions carefully and

save this manual for future use.

• The external appearance and other parts shown in this manual may differ from the actual product

within the scope that will not interfere with normal use due to improvement of the product.

 Do not use this bracket except with suitable cameras.

Failure to observe this may cause a drop resulting in injury or accidents.

 Refer installation work to the dealer.

Installation work requires technique and experience.

Failure to observe this may cause fire, electric shock, injury, or damage to the product.

Be sure to consult the dealer.

 Install the product securely on the bracket by following the installation

instructions.

Failure to observe this may cause injury or accidents.

 The screws and bolts must be tightened to the specied torque.

Failure to observe this may cause a drop resulting in injury or accidents.

 The measures of protection against a fall of this product shall be taken.

QSR5

QSR5QSR50

004F

4F4F

QSR50

QSR50QSR504M

4M4M

QQS

SSR

RR5

550

004

44F1

F1F1

QQSR

SRSR5

550

004M1

4M1

4M14M1

Failure to observe this may cause a drop resulting in injury or accidents.

Be sure to install the safety wire.

 Do not rub the edges of metal parts with your hand.

Failure to observe this may cause injury.

When using this product, also read the “Precautions” described in the operating

instructions for the camera to be attached.

Precautions

i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting

from failures arising out of improper installation or operation inconsistent with this

documentation or through use of parts other than this product, such as locally

procured parts.

Caution:

• Before attempting to connect or operate this

product, please read these instructions care-

fully.

Notice:

• This product is not suitable for use in loca-

tions where children are likely to be present.

• Do not install this product in locations where

ordinary persons can easily reach.

• For information about screws and other parts

required for installation, refer to the corre-

sponding section of this document.

https://www.i-pro.com/

Mount Bracket

Model No. WV-QSR504

Operating Instructions

Included Installation Instructions

Other items that are needed (not included)

Common

• Screws to fix a locally procured bracket on the installation surface

QSR50

QSR50QSR504

QSR50

QSR50QSR504S

4S4S

• 5 mm (distance between two parallel sides of a hexagon) hex wrench

QSR5

QSR5QSR50

004F

4F4F

QSR50

QSR50QSR504M

4M4M

QQS

SSR

RR5

550

004

44F1

F1F1

QQSR

SRSR5

550

004M1

4M1

4M14M1

• Sealant for waterproof treatment

• Safety wire

• Safety wire fixing screw

• Use a screw having a pull-out strength that is enough to hold the sum of weight of the

camera, this bracket, locally procured bracket, wire and cables.

Preface

This product is a mount bracket for PTZ camera. Use this product when connecting the WV-S65340

series camera to a ceiling mount bracket, wall mount bracket or a locally procured bracket.

The latest information about the supported cameras

The model number is abbreviated in some descriptions in this manual.

Specifications

 In order to prevent injury, this product must be securely mounted to a bracket

according to Installation Guide.

 Mounting method for this product

This product is designed to be used as a pendant mount camera. If it is mounted on a desktop or at

a slant, the camera may not work correctly and its lifetime may be shortened.

 Installation place

QSR50

QSR50QSR504S

4S4S

Salt damage prevention is applied to this product. However, it is not completely anti-corrosive.

Therefore, consider a place for installation where direct splash of seawater can be avoided.

Especially when installing this product in a seashore area or a place where a snow-melting agent is

applied, and also where rainwater is avoided, it is recommended to regularly clean and rinse off salt

with water. In case of installing this product in a seashore area, regularly check the status of equip-

ment. (Replace the parts as required.)

 Make sure to remove this product if it will no longer be used.

Precautions for installation

Standard Accessories

Operating Instructions (this document) 1 pc. ...................................

QSR50

QSR50QSR504

QSR50

QSR50QSR504S

4S4S

Hexagon screw (M6) 5 pcs. ............................................................

(of them, 1 for spare)

Ambient operating temperature: –50 °C to +60 °C {–58 °F to +140 °F}

Dimensions: Maximum diameter: ø175 mm {6-7/8 inches}

Height: 121 mm {4-3/4 inches}

Mass:

Approx. 1.0 k {2.21 lbs}g

Finish:

Main body: Aluminum die cast,

QSR50

QSR50QSR504

QSR5

QSR5QSR50

004F

4F4F

QSR50

QSR50QSR504M

4M4M

QQS

SSR

RR5

550

004

44F1

F1F1

QQSR

SRSR5

550

004M1

4M1

4M14M1

i-PRO white/black

QSR50

QSR50QSR504S

4S4S

Heavy salt damage prevention coating, i-PRO white

Installation

 Check of combination of brackets

• Brackets with normal specification

QSR50

QSR50QSR504

+ WV-QCL501

(Ceiling mount bracket)

+ WV-QWL501

(Wall mount bracket)

• Brackets with heavy salt damage resistance

specification

QSR50

QSR50QSR504S

4S4S

+ WV-QCL501S

(Ceiling mount bracket)

+ WV-QWL501S

(Wall mount bracket)

Note:

• Refer to the operating instructions of each

bracket for how to fix the brackets to be used

with to the installation surface.

Step1

Step2

Step3

Step4

Check of brackets

40A, Rp 1-1/2,

11 crest

depth 25.4 mm

{1 inch}

(parallel thread)

40A, NPT 1-1/2,

11.5 crest

length 25.4 mm

{1 inch}

(taper pipe thread)

40A, NPSC 1-1/2,

11.5 crest

depth 25.4 mm

{1 inch}

(parallel thread)

ISO mark

Step5

Step6

Step7

Hexagon screw (4 pcs.) (M6: accessory)

Recommended tightening torque:

.45 N·m {1.81 lbf·ft}

Be sure to use the hexagon screw included with this product.

• Securely fasten when fixing

this product.

• Depending on the fixing posi-

tion of this bracket, the cam-

era may not face the front.

Perform an adjustment of the

camera direction by panning

the camera.

Recommended tightening torque:

0.69 N·m {0.5 lbf·ft}

This bracket

REAR mark

⇒ Follow the installation procedure described

in the installation guide or in the installation

procedure leaflet of the camera for the

subsequent procedures.

Refer to the installation guide or the installation

procedure leaflet of the camera for connection.

WV-QWL501

QSR5

QSR5QSR50

004F

4F4F

QQS

SSR

RR5

550

004

44F1

F1F1

QSR50

QSR50QSR504M

4M4M

QQSR

SRSR5

550

004M1

4M1

4M14M1

Waterproof treatment

Installed auxiliary wire

Wire hook

Connect the cables

to the camera

Safety wire

Installed auxiliary wire

WV-QCL501/

WV-QCL501S

WV-QWL501/

WV-QWL501S

Example of explanation

for installation

Preparations

⇒ Follow the installation procedure described

in the installation guide or in the installation

procedure leaflet of the camera for the

subsequent procedures.

①

③

②

• Select a fixing method in accordance with the installation place surface for a part where the

safety wire is to be fixed.

• Use the dedicated tool when processing the wire.

• Maximum weight of locally procured bracket: 5 k {11 lbs}g

“<Control No.: C****>” used in these documents should be used to search for information

on our technical information website (https://i-pro.com/global/en/surveillance/training-

support/support/technical-information) and will guide you to the right information.

WV-QSR504F-W

About notations

Connection part

specifications of this product

Mount bracket

corresponding with this product

QSR50

QSR50QSR504

4 holes

WV-QCL501, WV-QWL501

QSR50

QSR50QSR504S

4S4S

WV-QCL501S, WV-QWL501S

QSR5

QSR5QSR50

004F

4F4F

Female screw (ISO)

40A, Rp 1-1/2, 11crest

depth 25.4mm {1 inch}

(parallel thread)

Locally procured

40A, R 1-1/2, 11crest

length 25.4mm {1 inch} or more

(

taper pipe thread

)

QQS

SSR

RR5

550

004

44F1

F1F1

Female screw (ANSI)

40A, NPSC 1-1/2, 11.5 crest

depth 25.4mm {1 inch}

(parallel thread)

Locally procured

40A, NPT 1-1/2, 11.5 crest

length 25.4mm {1 inch} or more

(taper pipe thread)

QSR50

QSR50QSR504M

4M4M

Male screw (ISO)

40A, R 1-1/2, 11 crest

length 25.4mm {1 inch}

(

taper pipe thread

)

Locally procured

40A, Rp 1-1/2, 11 crest

depth 25.4mm {1 inch} or more

(parallel thread)

QQSR

SRSR5

550

004M1

4M1

4M14M1

Male screw (ANSI)

40A, NPT 1-1/2, 11.5 crest

length 25.4mm {1 inch}

(

taper pipe thread

)

Locally procured

40A, NPSC 1-1/2, 11.5 crest

depth 25.4mm {1 inch} or more

(parallel thread)

Wire specification: SUS ø1.5 mm {1/16 inches}, 7x7

Rupture strength: 1127 N {253 lbf} or higher

Inside dimension

34 mm {1-11/32 inches} or more

imping process

Inside

dimension

17 mm {21/32 inches}

or more

Installation

surface

Length: Distance to the wire hook on the camera through the

inside of the bracket + 50 mm {1-31/32 inches}

QSR5

QSR5QSR50

004F

4F4F

QQS

SSR

RR5

550

004

44F1

F1F1

QSR50

QSR50QSR504M

4M4M

QQSR

SRSR5

550

004M1

4M1

4M14M1

40A, R 1-1/2,

11 crest

length 25.4 mm

{1 inch}

(taper pipe thread)

QSR50

QSR50QSR504

QSR50

QSR50QSR504S

4S4S

→

Step1

QSR5

QSR5QSR50

004F

4F4F

QSR50

QSR50QSR504M

4M4M

QQS

SSR

RR5

550

004

44F1

F1F1

QQSR

SRSR5

550

004M1

4M1

4M14M1

→

Step3

–

Step7

Step2

Locally procured bracket

Safety wire (locally procured)

Produkt Specifikationer

Mærke:	I-PRO
Kategori:	Ikke kategoriseret
Model:	WV-QSR504

Har du brug for hjælp?

Hvis du har brug for hjælp til I-PRO WV-QSR504 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret I-PRO Manualer

I-PRO WV-QJB505-W Manual

9 Oktober 2025

I-PRO WV-QDC507C Manual

7 Oktober 2025

I-PRO WV-QJB502A Manual

29 September 2025

I-PRO WV-QWL500-W Manual

18 Juli 2025

I-PRO WV-QAT501-S Manual

17 Juli 2025

I-PRO WV-QCL500-S Manual

17 Juli 2025

I-PRO WV-QSR506 Manual

16 Juli 2025

I-PRO WV-QSR504 Manual

15 Juli 2025

I-PRO WV-QJB503 Manual

14 Juli 2025

I-PRO WV-QEM500-W Manual

27 Marts 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

IFM EBC066 Manual

1 November 2025

Dahua Technology HAC-ME1200E Manual

1 November 2025

Wimberley AP-554 Manual

1 November 2025

Eliminator Lighting E 108 Manual

1 November 2025

IFM EBC001 Manual

1 November 2025

Bluestork KB-MAC Manual

1 November 2025

IFM EBC021 Manual

1 November 2025

Yamazen EKS-V3 Manual

1 November 2025

Olimpia Splendid Bi2 SL SMART S1 Manual

1 November 2025

Russell Hobbs Colours Plus 20417-70 Manual

1 November 2025