Joblotron JA-60GSM Manual

Joblotron Overvågningskamera JA-60GSM

Læs gratis den danske manual til Joblotron JA-60GSM (11 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Joblotron JA-60GSM, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/11

JA-60GSM dialer module 1 / 11 MFJ51215

JA-60GSM dialer module

Installation manual

The JA-60GSM dialer is constructed for the JA-60, 63 and 65 alarm control panels. The dialer is used for communication via GSM. An

appropriate GSM provider is chosen according to the inserted SIM card. This Installation manual is intended for the JA-60GSM, version FJ61412.

The GSM module, when installed in the alarm control panel, enables:

 Automatic sending of an event’s text messages to up to 8 mobile phones

 Dialing of programmed telephone numbers and playing of an audible warning signal

 Data transfer to one or two Central Monitoring Stations (CMS)

 Remote control and programming of the alarm system via SMS instruction messages from a mobile phone or from Jablotron’s SMS

website

 Remote control and programming of the alarm system using a telephone set keypad (mobile or land line)

 Remote control of an appliance (heating system etc.) via telephone (mobile or land line)

 Phone calls and convenient receiving and sending of SMS messages using an SMS-8010 telephone set (optional accessories; except

GSM kits e.g. JK-05) attached to the dialer module (via the GSM network)

 Connection of the intercom SP-01 for communication with the premises

 Internet connection using the GPRS data transfer

 Programming of the alarm system via ComLink software

 Programming and remote supervision of the alarm system via Jablotron’s website www.gsmlink.cz

 Multi-language support (only available via keypad instructions)

1 Installation of the dialer

The JA-60GSM dialer can be installed into the telephone

communicator’s position in a JA-60, 63 or 65 control panel (either a

GSM module or a telephone line communicator module can be used in

a control panel – it is not possible to install both simultaneously).

a) Disconnect the control panel’s power supply (both AC and

backup battery). If the control panel has been previously used

before this installation, enter the programming mode before

disconnecting the power supply.

b) We recommend you to disable the SIM card PIN code

protection before you insert it into the dialer. Use a mobile phone

to perform this task (if you have a NOKIA phone, select: Menu,

Settings, Security settings, PIN code request, Off). If you insist on

usage of the PIN, see section 5.1.

c) Open the SIM card holder (by sliding it in the direction shown in

figure 1) and Insert the SIM card into the holder and close it by

sliding it back. – see figure 1.

d) Attach the dialer into the control panel case and connect its flat

cable to the control panel’s main board.

e) Connect the GSM antenna (never switch the power supply on

without a proper antenna)

f) Connect a SMS-8010 telephone set to the PHONE connector (or to

PHONE terminals) if desired. Only one telephone set can be attached

to the dialer. The PHONE output of the dialer should never be

connected to any other telephone network.

g) If you use the AUX output to control an appliance, connect its

cable to the AUX output terminals (normally open dry contact,

max. 100mA / 60V) – see figure 1.

SY MBO

SPAC E

CANCEL MENU NAMES CALLS WRITE READ

1 2 3

456

789



SM S

CA L L

M U T E

FLA SH

RE D IAL

SPEA KE R

figure 1

Note: if your control panel supports programming of the PgX and

PgY outputs for the AUX function (sequences 238 and 239), the

appliance can also be controlled wirelessly from the control panel

by incorporating a UC-216 or UC-222 receiver module into the

system.

h) Reconnect the control panel’s power supply (backup battery

and AC). The system will show a P, (programming mode). The red

LED on the GSM dialer will light permanently (indicating that the

module is establishing a connection with the GSM network). The

LED will switch off after the connection is successfully

established.

If the LED starts flashing, the module was not able to connect to

the GSM network. In this case, switch off the control panel’s power

completely. Remove the SIM card and insert it into a mobile phone

to confirm whether it is possible to connect to the network at this

location. You can also select a desired network manually if options

are available. Ensure that the SIM card does not request a PIN

code (optional use with a PIN code is described in section 5.1).

Once the SIM card works in the mobile phone, reinsert it into the

GSM dialer and repeat step h). If the GSM signal is weak in this

area, change the location of the GSM antenna before you try to

reestablish the connection.

i) Attach the control panel’s cover after the module has connected to

the GSM network (LED switched off).

j) Key in 97701 - to set texts of the communicator to English

language. (English is the default setting, so you can omit this step.)

k) Enter 971 on the alarm system keypad (while in programming

mode) to monitor the GSM signal. The keypad will show a

number from 0 to 9 and it will sound a beep every second

indicating a new measurement. For proper functioning of the dialer

the signal strength should be 3 or higher. Find the best location for

the antenna while measuring the signal strength. To switch the

system back to programming mode press the N key.

l) Without additional programming you can test the user features of

the dialer (phone calls from an attached phone, remote control of

the system via a remote phone, remote control of an appliance

etc.). See the following description.

m) Set telephone numbers for automatic event reporting and the

other selectable features – see part 3.

n) Programming of the GSM dialer is possible by entering

programming sequences via the alarm system’s keypad (while in

programming mode). The most convenient programming method,

however is via a connected PC using ComLink software, or by

using the www.GSMlink.cz website.

JA-60GSM dialer module 2 / 11 MFJ51215

2 User features of the GSM dialer

The installed GSM dialer offers many useful features described in detail

below, or briefly in table 11. A synopsis is available on the user card.

The installer should properly demonstrate the use of the system to the

user after installation.

2.1 Phone calls from the attached telephone set

After the GSM module is connected to the GSM network, an attached

SMS phone can be used to make calls. If you pick up the phone, you will

hear a dial tone. Simply dial the number you want to call (as if you are

dialing from a normal fixed line phone). You can also dial the GSM

communicator’s phone number from another phone, and its attached phone

will ring as a normal land line phone would. If it is necessary to

communicate with CMS the call from the attached phone will be terminated

in 10 minutes.

If there is a busy tone on the attached telephone set, either the line you

are calling is busy, or the GSM communicator is busy with previous

communication at that moment (for example data transfer to the monitoring

station).

You can also use the attached phone keypad to operate the alarm

system. By pressing the # key, you can toggle the keypad from telephone

mode to alarm system control mode.

Note: some telephone sets are sensitive to the GSM radio signal. For

this reason you may hear a characteristic noise in the telephone

receiver when calling. If the noise is disturbing, change the location of

the phone set (try to keep it as far as possible from the GSM dialer

antenna). Usually it is possible to find a suitable location for the phone

with a minimal level of interference.

2.2 Remote control of the alarm system by telephone

A system equipped with a GSM dialer can be remotely controlled. From a

mobile phone there are two possibilities – either by text instructions sent by

SMS or by dialing-in and operating the system via the phone keypad which

will operate in the same way as the alarm system keypad. The dialing-in

method can also be done from an ordinary landline telephone set.

The following description matches the factory default settings of the

communicator. The described features can be greatly modified in the

programming mode – see part 4.

2.3 General rules for remote control by SMS instructions

 SMS instructions can be sent from a mobile phone or from an SMS

website.

 In SMS, letters are not case-sensitive. Only the basic English alphabet

is accepted by the communicator.

 All SMS instruction words must be separated by a space.

 If the % is used all previous text will be ignored. The %% symbol when

used in SMS text ends processing – all the following text will be

ignored. It is recommended to use this symbol at the end of the

instruction if the provider sends some additional text after your

message (advertisements etc.).

 Warning: if any incoming SMS includes except a valid system

command any extra text which is not separated by % or %%

symbols the command will not be executed

Examples of SMS:

“Hi, this text will be ignored even if I write ME % MO %% Thank

you” – Only MO command will be executed

“Hi, MO” – Command in the SMS will be ignored because there is

an extra text

 The default command texts can be customized by an installer (see

4.2.2). For example the instruction AUXON can be changed to

SWITCH ON HEATING etc.

2.4 Arming by SMS (AM xxxx)

The command AM followed with a valid access code can be used to

arm the alarm system. If the system is already armed, the command will

have no effect. SMS text to be sent to the dialer: AM



xxxx

xxxx is a valid alarm system access code (Master or user).



 separating character, which can be replaced by a space

Example: Sending AM 1234 will arm the system, which is equivalent to

using code 1234 for arming by keypad

Notes:

 According to the default setting, the system confirms command

execution with a corresponding SMS reply

 If it is impossible to arm the system – for example if it is in programming

mode, you will be notified about the situation by an SMS reply

 If the alarm system is split, the instruction will effect the section which

belongs to the access code used

 If arming without a code is enabled on the control panel, the AM

command can be used without any access code. In this case the

command performs the same action as the keys F 1 pushed on a

keypad.

2.5 Disarming by SMS (DM xxxx)

Command DM followed with a valid access code will disarm the system.

If the system is already disarmed, the command will have no effect. SMS

text to be sent to the communicator: DM xxxx

xxxx is a valid alarm system access code (Master or user).



 separating character, which can be replaced by a space

Example: Sending DM



1234 will disarm the system, which is

equivalent to entering code 1234 on a system keypad.

Notes:

 The system confirms disarming with a corresponding SMS reply

 If it is impossible to disarm the system – for example it is in programming

mode, you will be notified about the situation by an SMS reply

 If the alarm system is split, the instruction will effect the section which

belongs to the access code used

* If the alarm system is split and a command is used (AM or DM), the user

code will effect the system the same way as if the code had been entered

from the alarm system keypad – no matter if AM or DM is used (will arm if

the system is disarmed and will disarm if the system is armed).

2.6 Mode request by SMS (MO)

Command MO can be used to read the current alarm system mode.

The dialer will reply with a reporting SMS to the phone which sent the

MO command about status, level of GSM signal, GPRS status, success

of transferring data to the CMSs. SMS text to be sent to the dialer: MO

Example: If the system is armed, it will reply to the MO instruction with

the SMS: Alarm system reports: Control panel status:

Armed,GSM:7,GPRS OK,MS1 NOT,MS2 OK

Note: if you want to protect this command with a password, set your

own instruction text including the password – see section 4.2.2

2.7 Last event request by SMS (ME)

Instruction ME can be used to read the last event recorded in the alarm

system’s memory. The dialer will reply with a reporting SMS. SMS text

to be sent to the dialer: ME

Example: After a fire alarm, it will reply to the ME instruction with the

SMS: Alarm system reports: Last event: Alarm end Control panel Time:

02.06. 19:48

Note: if you want to protect this command with a password, set your

own instruction text including the password – see section 4.2.2.

2.8 Appliance remote control by SMS (AUXON, AUXOFF)

These commands can be used to operate the AUX output (for example

the heating in a house). The dialer confirms command execution with

an SMS reply.

To switch on the AUX output, send SMS text: AUXON

To switch off the AUX output, send SMS text: AUXOFF

Example: to switch on heating send SMS: AUXON

Note: texts of these instructions can be customized and protected with

a password – see section 4.2.2. Outputs PgX and PgY can be

controlled by SMS commands PGON and PGOFF.

2.9 Remote programming of the alarm by SMS (yyyyy PRG seq)

Command PRG can be used to send programming and operating

sequences to the alarm system. It has the same effect, as if the sequences

had been entered on the alarm system keypad. Type the instruction as:

yyyyy 



 



PRG seq,seq,seq,

where

yyyyy is the remote access code; factory default setting is 0000 (4

zeros); the code can be changed, see section 5.4

PRG is the command identification

seq are the programming or operating sequences, consisting of

characters 0 to 9, F, N. There can be more than one sequence in

one SMS. The particular sequences should be separated with a

comma or dot. The number of sequences in one SMS is limited

by the maximum size of the SMS in the GSM network.



 separating character, which can be replaced by a space

Example: if the control panel is disarmed and its Installer code is 6060, then

the duration of the alarm can be programmed to 5 minutes and the acoustic

indication of the exit delay can be disabled by sending the following SMS:

0000 PRG F06060,225,330,N

After receiving the SMS command, the control panel will first enter

programming mode (F06060) then sequences 225 and 330 will be

executed and at the end programming mode will be exited (N).

Produkt Specifikationer

Mærke:	Joblotron
Kategori:	Overvågningskamera
Model:	JA-60GSM

Har du brug for hjælp?

Hvis du har brug for hjælp til Joblotron JA-60GSM stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Overvågningskamera Joblotron Manualer

Joblotron H-915 Manual

13 Maj 2024

Joblotron JA-60 Manual

18 April 2024

Joblotron JA-63E Manual

17 April 2024

Joblotron SP-02 Manual

6 April 2024

Joblotron GS-130 Manual

6 April 2024

Joblotron UC-230 Manual

1 April 2024

Joblotron UC-261 Manual

27 Marts 2024

Joblotron JA-60M Manual

6 Marts 2024

Joblotron JA-80A Manual

6 Marts 2024

Joblotron JK-16 Manual

6 Januar 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

Marshall CV605-BK Manual

15 Juni 2025

IDIS DC-S6281FX Manual

15 Juni 2025

Marshall CV630-NDIW Manual

15 Juni 2025

Marshall CV730-ND3W Manual

15 Juni 2025

Marshall CV605-U3W Manual

14 Juni 2025

Marshall CV620-BK4 Manual

14 Juni 2025

Marshall CV730-BHN Manual

14 Juni 2025

Marshall CV730-WHN Manual

14 Juni 2025

Marshall CV630-BI Manual

14 Juni 2025

Sony SNC-WL862 Manual

14 Juni 2025