JUNG UD1755REG Manual

JUNG Lysdæmper UD1755REG

Læs gratis den danske manual til JUNG UD1755REG (7 sider) i kategorien Lysdæmper. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om JUNG UD1755REG, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/7
LB management
LB management
LB management
LB managementLB management
Universal dimmer LED
Universal dimmer LED
Universal dimmer LED
Universal dimmer LED
Universal dimmer LEDUniversal dimmer LED
Art. no.: UD1755REG
Operating instructions
Operating instructions
Operating instructions
Operating instructionsOperating instructions
1
1
1
11 Safety instructions
Safety instructions
Safety instructions
Safety instructionsSafety instructions
Electrical devices may only be mounted and connected by electrically skilled persons.
Electrical devices may only be mounted and connected by electrically skilled persons.
Electrical devices may only be mounted and connected by electrically skilled persons.
Electrical devices may only be mounted and connected by electrically skilled persons.Electrical devices may only be mounted and connected by electrically skilled persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Serious injuries, fire or property damage possible. Please read and follow manual fully.Serious injuries, fire or property damage possible. Please read and follow manual fully.
Danger of electric shock. Always disconnect before carrying out work on the device or load.
Danger of electric shock. Always disconnect before carrying out work on the device or load.
Danger of electric shock. Always disconnect before carrying out work on the device or load.
Danger of electric shock. Always disconnect before carrying out work on the device or load.Danger of electric shock. Always disconnect before carrying out work on the device or load.
Danger of electric shock. Device is not suitable for disconnection from supply voltage. The load
Danger of electric shock. Device is not suitable for disconnection from supply voltage. The load
Danger of electric shock. Device is not suitable for disconnection from supply voltage. The load
Danger of electric shock. Device is not suitable for disconnection from supply voltage. The loadDanger of electric shock. Device is not suitable for disconnection from supply voltage. The load
is not electrically isolated from the mains even when the device is switched off.
is not electrically isolated from the mains even when the device is switched off.
is not electrically isolated from the mains even when the device is switched off.
is not electrically isolated from the mains even when the device is switched off.is not electrically isolated from the mains even when the device is switched off.
Risk of destruction if the set operating mode and load type do not match. Set correct operating
Risk of destruction if the set operating mode and load type do not match. Set correct operating
Risk of destruction if the set operating mode and load type do not match. Set correct operating
Risk of destruction if the set operating mode and load type do not match. Set correct operatingRisk of destruction if the set operating mode and load type do not match. Set correct operating
mode when connecting or exchanging the load.
mode when connecting or exchanging the load.
mode when connecting or exchanging the load.
mode when connecting or exchanging the load.mode when connecting or exchanging the load.
Fire hazard. For operation with inductive transformers, each transformer must be fused on the
Fire hazard. For operation with inductive transformers, each transformer must be fused on the
Fire hazard. For operation with inductive transformers, each transformer must be fused on the
Fire hazard. For operation with inductive transformers, each transformer must be fused on theFire hazard. For operation with inductive transformers, each transformer must be fused on the
primary side in accordance with the manufacturer's instructions. Only safety transformers ac-
primary side in accordance with the manufacturer's instructions. Only safety transformers ac-
primary side in accordance with the manufacturer's instructions. Only safety transformers ac-
primary side in accordance with the manufacturer's instructions. Only safety transformers ac-primary side in accordance with the manufacturer's instructions. Only safety transformers ac-
cording to EN 61558-2-6 may be used.
cording to EN 61558-2-6 may be used.
cording to EN 61558-2-6 may be used.
cording to EN 61558-2-6 may be used.cording to EN 61558-2-6 may be used.
These instructions are an integral part of the product, and must remain with the end customer.
These instructions are an integral part of the product, and must remain with the end customer.
These instructions are an integral part of the product, and must remain with the end customer.
These instructions are an integral part of the product, and must remain with the end customer.These instructions are an integral part of the product, and must remain with the end customer.
2
2
2
22 Intended use
Intended use
Intended use
Intended useIntended use
Intended use
Intended use
Intended use
Intended useIntended use
– Switching and dimming of lighting
– Mounting in a sub-distribution unit on DIN rail according to EN 60715
– Operation is performed using the buttons, 2-wire or 3-wire extension with button cover,
rotary dimmer extension or push-button with NO contact
3
3
3
33 Product characteristics
Product characteristics
Product characteristics
Product characteristicsProduct characteristics
– Device works according to the leading edge phase control or trailing edge phase control
principle
– Automatic or manual setting of the dimming principle suitable for the load
– Display of the set operating mode by means LED
– Switch-on via bulb-preserving soft start
– Switch on with last saved brightness or saved switch-on brightness
– Switch-on brightness can be saved permanently
– Minimum brightness can be saved permanently
– Electronic short-circuit protection with permanent switch-off after 7 seconds at the latest
– Electronic over-temperature protection
Power extension possible by means of power boosters.
4
4
4
44 Operation
Operation
Operation
OperationOperation
These instructions describe operation using the buttons on the device and using a 2-wire or 3-
wire extension with a button cover or push-button as extension.
The LED display (1) turns green when the load is switched on.
Switching the light
Switching the light
Switching the light
Switching the lightSwitching the light
￭ Press the button or button cover briefly: Light is switched on at the last set brightnessn
or the stored switch-on brightness.
￭ Press the button or button cover briefly: The light is switched off.o
3-wire extension: Press top to switch on, press bottom to switch off.
1 / 7
82400023 13.03.2020
J0082400023
LB management
LB management
LB management
LB managementLB management
Universal dimmer LED
Adjusting the brightness
Adjusting the brightness
Adjusting the brightness
Adjusting the brightnessAdjusting the brightness
Light is switched on.
￭ Long press the button or button cover at the top.n
The light gets brighter up to maximum brightness.
￭ Long press the button or button cover at the bottom.o
Light gets darker to minimum brightness.
Switch light on with minimum brightness
Switch light on with minimum brightness
Switch light on with minimum brightness
Switch light on with minimum brightnessSwitch light on with minimum brightness
￭ Long press the button or button cover at the bottom.o
Light switches on at minimum brightness.
￭ Long press the button or button cover at the top.n
Light switches on at minimum brightness and gets brighter.
Save switch-on brightness
Save switch-on brightness
Save switch-on brightness
Save switch-on brightnessSave switch-on brightness
In the state as supplied, the switch-on brightness is set to maximum brightness.
￭ Set light to the required brightness.
￭ Press the button and or button cover over the entire surface for longer thann o
4 seconds.
Switch-on brightness is saved. For confirmation, the light is switched off briefly and
switched on again.
Delete switch-on brightness
Delete switch-on brightness
Delete switch-on brightness
Delete switch-on brightnessDelete switch-on brightness
￭ Briefly press the button or button cover: Light switches on at the saved switch-on bright-n
ness.
￭ Press the button and or button cover over the entire surface for longer thann o
4 seconds.
The switch-on brightness is deleted. Switching on takes place at the last brightness value
set. For confirmation, the light is switched off briefly and switched on again.
Operation via push-button as extension
Operation via push-button as extension
Operation via push-button as extension
Operation via push-button as extensionOperation via push-button as extension
￭ Press push-button briefly: Light is switched on or off at the last set brightness or a stored
switch-on brightness.
￭ Long press on the push-button when switched on: Set the brightness. The dimming direc-
tion is changed with each new long actuation.
￭ Long press on the push-button when switched off: Light switches on at minimum bright-
ness and gets brighter.
Saving or deleting the switch-on brightness is not possible.
5
5
5
55 Information for electrically skilled persons
Information for electrically skilled persons
Information for electrically skilled persons
Information for electrically skilled personsInformation for electrically skilled persons
5.1
5.1
5.1
5.15.1 Fitting and electrical connection
Fitting and electrical connection
Fitting and electrical connection
Fitting and electrical connectionFitting and electrical connection
DANGER!
Mortal danger of electric shock.
Mortal danger of electric shock.
Mortal danger of electric shock.
Mortal danger of electric shock.Mortal danger of electric shock.
Disconnect the device. Cover up live parts.
Disconnect the device. Cover up live parts.
Disconnect the device. Cover up live parts.
Disconnect the device. Cover up live parts.Disconnect the device. Cover up live parts.
2 / 7
82400023 13.03.2020
J0082400023

Produkt Specifikationer

Mærke: JUNG
Kategori: Lysdæmper
Model: UD1755REG

Har du brug for hjælp?

Hvis du har brug for hjælp til JUNG UD1755REG stil et spørgsmål nedenfor, og andre brugere vil svare dig


Lysdæmper JUNG Manualer

JUNG

JUNG 1252UDE Manual

3 August 2024
JUNG

JUNG UD1755REG Manual

31 Juli 2024
JUNG

JUNG UD1255REG Manual

31 Juli 2024
JUNG

JUNG 247.07EB Manual

30 Juli 2024
JUNG

JUNG 1724DEB Manual

25 Juli 2024
JUNG

JUNG 1730DD Manual

13 Januar 2024
JUNG

JUNG CD5544.03V Manual

24 November 2023
JUNG

JUNG 1724DM Manual

28 Oktober 2023
JUNG

JUNG 1271LEDDE Manual

17 September 2023
JUNG

JUNG 1731DD Manual

8 September 2023

Lysdæmper Manualer

Nyeste Lysdæmper Manualer

Vimar

Vimar 14138.120.SL Manual

24 Juli 2025
Vimar

Vimar 20137.N Manual

24 Juli 2025
Vimar

Vimar 19147.M Manual

24 Juli 2025
Vimar

Vimar 19139.M Manual

24 Juli 2025
Vimar

Vimar 20142.N Manual

24 Juli 2025
Gira

Gira 2263 Manual

22 Juli 2025
Gira

Gira 2261 Manual

22 Juli 2025
Crestron

Crestron CLW-DIMFLVEX-P-DA Manual

9 Juli 2025
Crestron

Crestron CLW-DIMUEX-P Manual

9 Juli 2025
Crestron

Crestron CLW-DELVEX-P Manual

9 Juli 2025