JUNG 1271LEDDE Manual

JUNG Lysdæmper 1271LEDDE

Læs gratis den danske manual til JUNG 1271LEDDE (6 sider) i kategorien Lysdæmper. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 13 anmeldelser. Har du et spørgsmål om JUNG 1271LEDDE, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

LED touch dimmer insert

Light Management

LED touch dimmer insert

Art. No. 1271 LEDDE

Operating instructions

1 Safety instructions

Electrical equipment may only be installed and fitted by electrically skilled persons.

Serious injuries, fire or property damage possible. Please read and follow manual fully.

Danger of electric shock. Always disconnect before carrying out work on the devise or

load. At the same time, take into account all circuit breakers that supply dangerous

voltage to the device or load.

Danger of electric shock. Device is not suitable for disconnection from supply voltage.

The load is not electrically isolated from the mains even when the device is switched off.

Do not connect any LED or compact fluorescent lamps that are not specifically suitable

for dimming. Device can be damaged.

Do not connect any lights with integrated dimmers. Device can be damaged.

Danger of electric shock. Do not operate the insert without a cover.

These instructions are an integral part of the product, and must remain with the end

customer.

2 Device components

Figure 1: Device components

(1) FM insert

(2) Frame

(3) Cover

(4) Setter, minimum brightness

(5) Terminals

1/6

82587503

J:0082587503 27.05.2013

3 Function

Intended use

- Switching and dimming of incandescent lamps, HV halogen lamps, HV LED and compact

fluorescent lamps

- Suitable for mixed-load operation of ohmic load (incandescent lamps, HV halogen lamps)

and HV LED lamps

- Suitable for mixed-load operation of ohmic load (incandescent lamps, HV halogen lamps)

and compact fluorescent lamps

- Installation in appliance box according to DIN 49073

- Operation with suitable cover

i No mixed-load operation of HV LED and compact fluorescent lamps. Only connect lamps

of one manufacturer and of the same type.

i No operation with transformers.

i HV-LED and compact fluorescent lamps generate high pulsed currents, when they are

operated in the leading edge phase control. Depending on the design and power rating of

these lamps, the connected load of the specified values could vary.

Product characteristics

- Device works according to the phase cut-on principle

- Device can also be operated without neutral conductor

- Bulb-preserving soft start

- Switch-on brightness can be saved permanently

- Minimum brightness can be set

- Connection of extensions possible

- Power failures of more than 1 second will cause the device to switch off

- Electronic short circuit protection with permanent switch-off

- Electronic over-temperature protection

i Flickering of the connected lamps due to undershoot of the specified minimum load or

through centralised pulses from the power stations. This does not represent any defect in

the device.

4 Operation

These instructions describe operation with a pushbutton cover (see Accessories). Operation

with a different cover is described in the instructions for the cover in question. Operation on the

main device or 2-wire extension is identical.

i Extension operation is only possible if there is a cover fitted on the main device.

Switch light

o Press button for less than 0.4 seconds.

Adjust the brightness

Light is switched on.

o Press button at top for longer than 0.4 seconds.

The light gets brighter up to maximum brightness.

o Press button at bottom for longer than 0.4 seconds.

Light gets darker to minimum brightness.

i Installation button: the light becomes brighter up to maximum brightness, remains there

briefly and becomes dimmer down to minimum brightness, remains there briefly and

becomes brighter again. This process repeats for as long as the push-button remains

pressed.

Switch light on with minimum brightness

o Press button at bottom for longer than 0.4 seconds.

Save switch-on brightness

o Set light to the required brightness.

o Press button over entire surface for longer than 3 seconds.

2/6

82587503

J:0082587503 27.05.2013

Light Management

LED touch dimmer insert

Produkt Specifikationer

Mærke:	JUNG
Kategori:	Lysdæmper
Model:	1271LEDDE

Har du brug for hjælp?

Hvis du har brug for hjælp til JUNG 1271LEDDE stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lysdæmper JUNG Manualer

JUNG 1252UDE Manual

3 August 2024

JUNG UD1755REG Manual

31 Juli 2024

JUNG UD1255REG Manual

31 Juli 2024

JUNG 247.07EB Manual

30 Juli 2024

JUNG 1724DEB Manual

25 Juli 2024

JUNG 1730DD Manual

13 Januar 2024

JUNG CD5544.03V Manual

24 November 2023

JUNG 1724DM Manual

28 Oktober 2023

JUNG 1271LEDDE Manual

17 September 2023

JUNG 1731DD Manual

8 September 2023

Lysdæmper Manualer

Nyeste Lysdæmper Manualer

Vimar 14138.120.SL Manual

24 Juli 2025

24 Juli 2025

24 Juli 2025

24 Juli 2025

24 Juli 2025

22 Juli 2025

22 Juli 2025

Crestron CLW-DIMFLVEX-P-DA Manual

9 Juli 2025

Crestron CLW-DIMUEX-P Manual

9 Juli 2025

Crestron CLW-DELVEX-P Manual

9 Juli 2025