Kicker IX 405D Impulse 5 C Manual

Kicker Bilradio IX 405D Impulse 5 C

Læs gratis den danske manual til Kicker IX 405D Impulse 5 C (12 sider) i kategorien Bilradio. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Kicker IX 405D Impulse 5 C, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/12

Congratulations! You have just purchased one of the latest in a long line

of exceptional car audio power amplifiers from Stillwater Designs. Your

KICKER IX405D was designed and engineered by the same team which

created many other international award winning KICKER components like the

ZR, ZX, DX, and XS-Series amps. It contains a number of cutting-edge features

that let you build an entire car audio system around this single power

component. It will give you years of outstanding performance and

dependability when installed in a properly designed system.

Thanks for buying KICKER. Enjoy.

KICKER IMPULSE AMPLIFIER FEATURES

Separate electronic crossovers are built in for convenience and allow you to

select full range or highpass for front and rear channels as well as lowpass fre-

quencies for the sub output.

The Kicker Impulse IX405 Amplifier is 2 Ohm stable on all five channels; the

sub out can be bridged to as low as 2 Ohm mono. For connection to the source ,

you have the option of low level RCA inputs or a high level input for use with

radios that don’t have RCA outputs.

Separate KICKEQ bass and treble controls give you the ability to boost low

and high frequencies to tailor the music to your taste. Dash-mounted remote

control lets you adjust bass output levels from your listening position.

Auto-resetting short circuit and overthermal protection circuits are incorpo-

rated to protect the amplifier from failure due to extreme conditions.

State of the art circuitry including MOSFET power supply and glass epoxy cir-

cuit boards are used to ensure many years of trouble free operation.



IMPULSE IX405D

Five-Channel Power Amplifier

Wiring

The preferred method of bringing input signal in to the amplifier is with RCA

cables from a quality tape or CD player. A high (speaker) level input signal may also

be used if your factory deck or aftermarket source does not have low level RCA

jacks. It is not recommended to mix high and low level inputs. Engine noise in the

system will probably result.

Some of the system possibilities are shown in the System Diagrams section of

this manual.

When working with power connections always hook up the ground wire first

and disconnect the ground wire last. Never make any wiring changes with the

amplifier powered up.

The chassis mounted fuse(s) are in place to protect the circuitry of the

amplifier in the event of major trouble. An in-line fuse must be installed within 18

inches of the battery to protect the power wire used to supply current to the

amplifier. For the Kicker Impulse IX405D amplifier a fuse value of 60A and 8 gauge

power wire are recommended. If the power wire is longer than 10 feet, we rec-

ommend that the wire size be 4 gauge to reduce losses.

Any time that a power wire goes through a metal panel such as the firewall,

or if there is any chance of abrasion, it is necessary to use a grommet or other

suitable form of protection to avoid shorts.

The ground wire should be at least 8 gauge, as short as possible and

attached to the body of the vehicle. The ground point must be free from paint

and corrosion. We recommend using the same gauge wire for power and ground.

Mounting the IMPULSE Amplifier

After determining an appropriate mount-

ing location which provides good air circulation

and access to the end panel controls, use the

supplied screws and washers to firmly mount

the amplifier. The amplifier chassis can be

used as a template for the screw locations.

Check to make sure that the mounting screws

will not damage any components on the back

side of the chosen mounting surface.

If a vertical mounting surface is chosen,

we recommend that the heatsink fins run ver-

tically as shown for improved cooling.

The subwoofer remote controller can be

mounted in any convenient location in the

vehicle. It should be within easy reach of the

driver to avoid any dangerous situations while

driving.

Produkt Specifikationer

Mærke:	Kicker
Kategori:	Bilradio
Model:	IX 405D Impulse 5 C

Har du brug for hjælp?

Hvis du har brug for hjælp til Kicker IX 405D Impulse 5 C stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Bilradio Kicker Manualer

Kicker KX300.4 Manual

4 Oktober 2024

Kicker IX 406 Impulse Manual

22 September 2024

Kicker DX500.1 Manual

12 September 2024

Kicker IX 702 Impulse Manual

31 August 2024

Kicker KX850.2 Manual

31 August 2024

Kicker X50 Manual

23 August 2024

Kicker zx 350 2 Manual

23 August 2024

Kicker KX 400.4 Manual

22 August 2024

Kicker ZX 300.1 Manual

22 August 2024

Kicker kx 600 1 Manual

22 August 2024

Bilradio Manualer

Nyeste Bilradio Manualer

Krüger&Matz KM2014 Manual

9 Juni 2025

Blow Pilot AVH-8624 Manual

9 Juni 2025

Krüger&Matz KM2009 Manual

9 Juni 2025

Krüger&Matz KM2004 Manual

9 Juni 2025

Vordon York HT-930 Manual

8 Juni 2025

Carlinkit CPC200-U2W Plus Manual

8 Juni 2025

Vordon Jersey HT-800 Manual

8 Juni 2025

Peiying PY-8288 Manual

7 Juni 2025

Boss MCK508WB Manual

7 Juni 2025

Peiying PY-9348 Manual

6 Juni 2025