Kicker ZR1000 Manual

Kicker Bilradio ZR1000

Læs gratis den danske manual til Kicker ZR1000 (12 sider) i kategorien Bilradio. Denne vejledning er vurderet som hjælpsom af 43 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 22 anmeldelser. Har du et spørgsmål om Kicker ZR1000, eller vil du spørge andre brugere om produktet?

Side 1/12
Based on the same design philosophy as the original KICKER Amplifier,
the ZR-Series amplifiers from Stillwater Designs expand and improve the
standards for car audio amplifier performance. Features that defined the
way an amplifier should be built, attention to detail, flexibility, and pure
clean power have been retained and some important new
performance/reliability features have been added.
FEATURES & CONTROLS
The design goals for the ZR-Series amps were simple yet crucial: build the ultimate ampli-
fiers available for the brutal environment of a vehicle.
A new heatsink design provides maximum heat dissipation when air flow isn’t ideal. In
addition to the existing forms of protection already in effect (thermal, overvoltage, and
reverse polarity), a new short circuit protection circuit will allow the amplifier to operate
into a variety of loads including 1 Ohm stereo and 2 Ohm mono.
Gold plated custom tooled speaker and power connectors maximize power transfer and
damping. To improve the thermal stability, sound quality, and output power we have
upgraded the power supply switching MOSFETs.
Surface mount devices are used extensively throughout the design to increase reliability.
Features carried over from the last generation of amplifiers include:
ZRX Crossover Module included.
Active Signal Processing Modules are less expensive than outboard signal processors and
eliminate the possibility for electrical noises to enter the system.
RCA output jacks provide a simple method for daisy chaining multiple amplifiers, espe-
cially when the plug-in modules are used.
Optical isolation between the signal and power grounds has proven very effective to
keep automotive electrical noises from entering the signal path.
For the best sound quality possible we have eliminated coupling capacitors from the sig-
nal path through the use of a DC servo circuit.
Silent turn on/off circuitry eliminates pops to protect your speakers and makes your
system ready for competition.
Multiple amplifiers can be daisy chained without signal degradation because the input
impedance is 22,000 Ohms.
Stillwater Designs recommends that the amplifier be installed at an authorized dealer.
The length of your KICKER amplifier’s warranty is three times as long when installed by an
authorized KICKER dealer.
ZR120, ZR240, ZR360, ZR600 & ZR1000
STEREO POWER AMPLIFIERS
2
MOUNTING INSTRUCTIONS
The orientation of the amplifier is critical to proper cooling. The cooling fins are
designed to operate best when the amp is in a vertical position or mounted flat with the
fins up. It is important to keep the chassis of the amplifier isolated from the metal of the
vehicle because the heatsink is connected to signal ground for noise isolation. Grounding
the heatsink will cause a ground loop. The plastic inserts in the mounting feet of the amp
should remain in place as isolators. These inserts are designed to accept #8 screws for
mounting.
#8 Mounting
Screws
Isolation
Pads
#8 Mounting
Screws
VERTICAL
HORIZONTAL


Produkt Specifikationer

Mærke: Kicker
Kategori: Bilradio
Model: ZR1000

Har du brug for hjælp?

Hvis du har brug for hjælp til Kicker ZR1000 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Bilradio Kicker Manualer

Kicker

Kicker KX300.4 Manual

4 Oktober 2024
Kicker

Kicker IX 406 Impulse Manual

22 September 2024
Kicker

Kicker DX500.1 Manual

12 September 2024
Kicker

Kicker KX850.2 Manual

31 August 2024
Kicker

Kicker X50 Manual

23 August 2024
Kicker

Kicker zx 350 2 Manual

23 August 2024
Kicker

Kicker KX 400.4 Manual

22 August 2024
Kicker

Kicker ZX 300.1 Manual

22 August 2024
Kicker

Kicker kx 600 1 Manual

22 August 2024

Bilradio Manualer

Nyeste Bilradio Manualer