Kicker ZX550.2 Manual

Kicker Bilradio ZX550.2

Læs gratis den danske manual til Kicker ZX550.2 (10 sider) i kategorien Bilradio. Denne vejledning er vurderet som hjælpsom af 49 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 25 anmeldelser. Har du et spørgsmål om Kicker ZX550.2, eller vil du spørge andre brugere om produktet?

Side 1/10
ZX
STEREOAMPLIFIER
ZX ZX ZX ZX350 ,.2 450 ,.2 550 ,.2 850.2
©2006 Stillwater Designs
English Version
Versión spañolE
Amplificador del la erie ZX.2S
Manual del Propietario
Deutsche Version
S Stereoverstärker der ZX.2- erie
Benutzerhandbuch
Version Française
Amplificateur de série ZX.2
Manuel d'utilisation
Installation . . . as easy as 1, 2, 3
1. Mounting Choose a structurally sound location to mount your Kicker amplifier. The controls on the
top of the amplifier need to be accessible for adjustment. Make sure there are no items behind the area
where the screws will be driven. Choose a location that allows at least 4(10cm) of open ventilation for
the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill four
holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifier.
2. Wiring Disconnect the vehicles battery to avoid an electrical short. Then connect the ground wire
to the amplifier. Make the ground wire short, 24(60cm) or less, and connect it to a paint-and
corrosion-free solid-metal area of the vehicle's chassis. Adding an additional ground wire between the
battery's negative post and the vehicle chassis of this same gauge (or larger) is recommended.
Use a twisted pair of RCA (low-level) interconnect cable to feed the audio signal to the amplifier.
Only use speaker wire (high-level) inputs if
your source unit does not have RCA type
outputs. Either input method will provide a
low-level output signal at the RCA output,
which effectively passes the audio signal
to another amplifier or component
(P.A.S.T.). Keep the RCA cable away from
factory wiring harnesses and other power
wiring. If you need to cross this wiring,
cross it at a 90 degree angle.
Install a fuse within 18(45cm) of the
battery and in-line with the power cable
connected to your amplifier. If you ever
need to remove the amplifier from the
vehicle after it has been installed, the ground wire should be the last wire disconnected from the
amplifier--just the opposite as when you installed it. See the chart below for power and ground wire
size, and fusing recommendations.
3. Configuration The following
diagrams show the most common
configurations for your Kicker ZX series
amplifier.
Two Channel peration ( tereo) O S These ZX amplifiers are capable of operating into a minimum
impedance of 2 ohms per channel in stereo operation. See Figure 2.
Bridged Operation (Mono) ZX.2 series amplifiers are capable of operating into a minimum
impedance of 4 ohms when in bridged operation. See Figure 3.
S O S S Stereo and Mono peration imultaneously ( AM ) The ZX.2 series amplifiers are capable of
operating into a minimum impedance of 4 ohms mono and 2 ohms per channel in stereo
simultaneously with the use of passive crossovers. See Figure 4.
INSTALLAT OI N
ZX.2AMPLIFIER
ZX ZX ZX ZX350.2 /450.2 /550.2 /850.2
TwoChannelModels:
ZX.2SeriesAmplifier
Owner’sManual
Congratulations on your
KICKER purchase
Please record your purchase
information and keep your sales
receipt for validation of warranty.
Authorized Kicker Dealer:
Purchase Date:
Amplifier Model Number:
Amplifier Serial Number:
__________________________
__________________________
__________________________
__________________________
Model FuseZX350.2 50APowerG d 8rounWire GA
Model FuseZX450.2 60APowerG d 4rounWire GA
Model FuseZX550.2 70APowerG d 4rounWire GA
Model FuseZX850.2 120APowerG drounWire 2GA
Note: To get the best performance from your new Kicker Amplifier, we recommend using genuine Kicker Accessories and Wiring.
Note: All specifications and performance figures are subject to change. Please visit the www.kicker.com for the most current information.
23
C AONFIGUR T OI N
SOURCE UNIT
killers trk7“on Top”
INPUT
RL
L -+L- R+ R
O T TU PU
RL
H E EI-L V L
INPUT
+ +- - O OFF HI L
X VO ER
REMOT E BASS
F uig re 1
U h mp f ,se onl ney o type of signal input to t e a li ier
eit le ireher C bR A Ca or S peaker W
R A aC C ble
(Lo -Lw evel)
Input
Speaker Wire
(High-Level
O t tu pu )
Speaker Wire
(High-L puevel In t)
L fe t +
L fe t -
Right -
Right +
R A aC C ble
(Lo -Lw evel)
O t tu pu
C or ss erov
Switch
Re te Bassmo
Co puntro ul O t t
24"
Or Less
(60cm)
G droun
+
_
+
_
R-
R+
L-
L+
Re temo
Tu -rn On
Battery
+12V Fuse
Right S ea erp k
L f p ke t S ea er
18"
Or Less
Signal O t u (P. . .A S T.)
(45cm)
Signal In
Mini an e 2 s er eratimum i emp d c of ohm p channel in stereo op on
Re temo
Tu -rn On
Battery
+12V Fuse
18"
Or Less
(45cm)
Mini i an e s w en in ri ge eratimum mped c of 4 ohm h b d d op on
R-
R+
L-
L+
+
_
M no o
Speaker
Signal O t u (P. . .A S T.)
Signal In
24"
Or Less
(60cm)
G droun
24"
Or Less
(60cm)
G droun
+
_
+
_+
_
HIGH PASS
CROSSOVER
HIGH PASS
CROSSOVER L WO
PAS S
C -ROSS
OVER
L f p ke t S ea er
Rig erht Speak
M no o
Speaker
R-
R+
L-
L+
Remote
Tu -rn On
Battery
+12V Fuse
18"
Or Less
(45cm)
Mini i an e s an s er annel inmum mped c of 4 ohm mono d 2 ohm p ch
stere si ltane sl t e se assi e ss erso mu ou y with h u of p v c orov
Signal Out (P. . .A S T.)
Signal In
F u ig re 2
F uig re 3
F uig re 4
Signal uO t
( . . .P A S T.)


Produkt Specifikationer

Mærke: Kicker
Kategori: Bilradio
Model: ZX550.2

Har du brug for hjælp?

Hvis du har brug for hjælp til Kicker ZX550.2 stil et spørgsmål nedenfor, og andre brugere vil svare dig