Labelmate CAT-4-ACH Manual

Labelmate Ikke kategoriseret CAT-4-ACH

Læs gratis den danske manual til Labelmate CAT-4-ACH (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 51 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 26 anmeldelser. Har du et spørgsmål om Labelmate CAT-4-ACH, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

MAINTENANCE:

Your CAT-4 requires no maintenance.

Product Limited Warranty

All Labelmate Products are warranted to the original end-user customer to be free from defects in

materials and workmanship. If it is determined by Labelmate that a product has failed under the terms of

this warranty, the product will be repaired or replaced at no charge to the customer. Labelmate reserves all

rights to determination of coverage and liability under this warranty. The warranty period for all new

Labelmate products is outlined below:

The warranty period for all products starts on the date purchased by the original end-user customer.

Warranty coverage is not transferable with ownership and will terminate immediately upon rental, resale or

any other change in ownership. This warranty does not cover repair to any product which is damaged, has

been modiﬁed, is missing parts, or has been opened or repaired by any unauthorised person. Use of any

unauthorised accessory or attachment will void coverage. Purchase documentation should be retained for

coverage veriﬁcation.

In the event your product requires service, please contact the distributor you bought the product from. The

customer assumes responsibility for all cost and risk incurred in transport for service.

Labelmate makes no other warranty of any kind expressed or implied, or to suitability or ﬁtness for a

particular purpose. No other person, agent or reseller is authorised to give any warranties on behalf of

Labelmate. Any obligation to warranty other than that speciﬁcally addressed above is hereby disclaimed.

Warranty Period

Products Covered

5 years

Label Rewinders

Label Unwinders

3 years

Label Counters (mechanical parts

only)

Label Slitters (mechanical parts

only)

Label Dispensers

Printer Mechanisms

1 year

Power Supply Modules

Counter modules

Encoders

Any products not speciﬁed above.

LABELMATE SPRL

290, Chaussée de Ruisbroek, 1620 Drogenbos, BELGIUM

TEL: +32 2.375.69.60 FAX: +32 2.375.38.96 –

brussels@labelmate.com

www.labelmateeurope.com

CAT-4

Heavy-Duty "CAT" Label Rewinder

• Three Torque Range and

Direction Controls

• Constant Adjustable TorqueTM

"CAT" technology

• Adjustable Speed Control up to

125cm per second

• Precise Variable Speed Control

CAT - 4

REAR PANEL

Remove all parts from the shipping container and verify contents.

PACKAGE CONTENTS:

• User Manual (this document)

• CAT-4 Drive Unit

• Power Supply Module

• LABELMATE "Quick- -Locking Core Chuck Chuck" ™ Quick

or Standard Shaft with three (3) metal Vanes installed,

or Model- -INCHES Shaft with six (6) metal Vanes installed, 10

or Model ACH: Adjustable Core Holder –

• Two 300mm Plastic Flange Plates (One only for QC, none for ACH)

Retain the Shipping Container and Packaging for Storage and Transport

SPECIFICATIONS:

Weight of the machine: 9,6Kg to 11,1Kg depending on model.

Max. Label Roll Weight: STD: 8Kg ACH: 7Kg QC: 8Kg -IN: 10Kg. – – – 10

Max. Label Roll Diam.: 300mm (280mm for ACH).

Start/Stop: ON/OFF Power Switch

Power Supply: Input: 220 240VAC 50 60 Hz – – – .

Output: 15VDC 4.3 –3A

IMPORTANT INFORMATION:

• This product is a label rewinder. It is only to be used to rewind or unwind labels of the

recommended dimensions and weight in an indoor, dry environment.

• The machine has to be unplugged before any manipulation.

• The machine is to be used on a ﬂat surface, if the surface is not flat, it is to be ﬁxed using

the holes in the base plate.

• Do not leave the power cable in a passageway.

• The ambient light of the working area needs to be suﬃcient to avoid any risk.

• The rewinder can be used in ambient temperatures of +2°C to 40°C.

• Connection of the machine to the power source must respect local and European

legislations.

SET-UP:

(if you have the ACH Adjustable Core Holder option Skip to step 4).

1. STANDARD AND 10": Identify the inner Label Flange. Slide the Flange Plate onto the

hollow end of the Rewind Shaft. For maximum width, the Flange face should be ﬂush with

the end of the Shaft. Tighten the screw in the Hub until it is snug. Not too tight.

2. CHUCK: Mount the inner Flange onto the Quick-Chuck with two screws provided.

3. Slide the Shaft d Flange Assembly onto the CAT-4 Motor Shaft allowing for clearance to an

the CAT-4 Chassis and Motor Screws. Tighten the Allen Screw onto the ﬂat part of the

Motor Shaft until it is tight.

4. ACH: Slide the Hub of the ACH over the motor Shaft of the CAT-4 Position the Hub so .

there is a gap between the ACH Hub and the Rewinder Drive Unit case. Tighten the Allen

Screw onto the ﬂat part of the Motor Shaft until it is tight.

5. Set the CAT-4 in place near the label exit slot of the printer.

6. CAUTION: AVOID ACCIDENTS. THE CAT- WEIGHS OVER 10KG, SO CHOOSE ONLY

A STURDY SURFACE ON WHICH TO SET THE UNIT.

7. Verify that the "DIRECTION" Switch on the CAT-4 Control Panel is in the "OFF" position.

8. Plug the Power Plug at the end of the wire on the AC/DC Wall Transformer into the CAT-4

Power Input Jack. Plug the AC/DC Transformer into an appropriate AC power outlet. The

unit is now ready for use.

FOR YOUR SAFETY:

Switch oﬀ device before any manipulation.

REWINDING LABELS:

1. Place the "DIRECTION" Switch on the CAT-4 Control Panel in the centre "OFF" position.

2. Slide an empty label core over the Quick-Chuck or Vanes on the shaft until the core is

against the inner Flange Plate. On the Quick-Chuck, tighten the Lock Knob (for an ACH

see the ACH user manual).

3. If desired, slide the outer label Flange Plate (with Ball Plunger in the Hub) onto the Shaft

and up against the label core.

4. Feed the label web from the printer and secure it to the take-up roll core with tape. Rotate

the take-up reel a couple of turns.

5. Place the CAT-4 "TORQUE RANGE" Switch in the "MEDIUM" position. NOTE: When the

"TORQUE RANGE" Switch is in the " -4 develops higher torque. HIGH” position, the CAT

When the "TORQUE RANGE" Switch is in the " -4 develops lower LOW” position, the CAT

torque. Use the "HIGH” position for label slitting or rewinding large diameter rolls.

6. Rotate the "SPEED" Control Knob to the minimum position (fully counter-clockwise).

7. Place the CAT-4 "DIRECTION" Switch in the position desired to run left or right.

8. Start the printer and adjust the " " Control Knob for the desired take-up tension. Use SPEED

the minimum " " setting needed to rewind labels properly. Excessive torque might SPEED

pull the labels too hard and cause the printer to lose registration.

EXTERNAL HALT CONTROL:

The CAT-4 can be controlled by the printer. A 3.5mm (mono) connector for an External Control

Input (start/stop) is provided and a matching jack is enclosed. The CAT-4 can react to diﬀerent

types of signals provided by the printer. The selection of the signal nature is done via 3 jumpers

on the CAT-4 internal PCB. Four modes are selectable: Open Collector High Active, Open

Collector Low Active, Logic Level High Active ( ) & Logic Level Low Active ( Max 10VDC Max

10VDC) By default, the jumpers are on High Active position. . An optional “Start Delay” is

available in order to allow the printer to execute a back feed before starting the print cycle. The

start delay, adjustable from 0-3.5 seconds, will delay the printer after the command has been

received from the printer.

No tension arm option is available.

The factory setting is “Open Collector High”. Other default setting on request.

WARNING!

This Product is for indoor use only.

Not for use in wet locations.

JP1

JP2

JP3

SIG ACT LOW

2/3

OP COL HIGH

1/2

SIG ACT HIGH

1/2

OP COL LOW

2/3

Produkt Specifikationer

Mærke:	Labelmate
Kategori:	Ikke kategoriseret
Model:	CAT-4-ACH

Har du brug for hjælp?

Hvis du har brug for hjælp til Labelmate CAT-4-ACH stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Labelmate Manualer

Labelmate UCAT-40 Manual

6 August 2024

Labelmate CAT-4 Manual

6 August 2024

Labelmate UCAT-1-CHUCK Manual

6 August 2024

Labelmate S-100S Manual

6 August 2024

Labelmate CAT-4-ACH Manual

6 August 2024

Labelmate Count-200 Manual

6 August 2024

Labelmate Count-100 Manual

6 August 2024

Labelmate CAT-40G Manual

6 August 2024

Labelmate LD-100-U Manual

6 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

T'nB VINEKIT Manual

16 September 2025

T'nB PADA36W Manual

16 September 2025

T'nB TCUNSAM Manual

16 September 2025

Ikea HATTHOLMEN 105.084.80 Manual

16 September 2025

T'nB MHFIXDUAL Manual

15 September 2025

T'nB MHFLEX Manual

15 September 2025

T'nB ANIN02 Manual

15 September 2025

T'nB TCUNVES Manual

15 September 2025

T'nB NBSTANDFLEX Manual

15 September 2025

T'nB TCUN01 Manual

15 September 2025