Labelmate UCAT-1-CHUCK Manual

Labelmate Ikke kategoriseret UCAT-1-CHUCK

Læs gratis den danske manual til Labelmate UCAT-1-CHUCK (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Labelmate UCAT-1-CHUCK, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
© LABELMATE User_UCAT- -–40 CE 7 Original user manual. –05/1 – ● KEEP MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE ●
MAINTENANCE:
Your UCAT- 40 requires no maintenance.
Product Limited Warranty
All Labelmate Products are warranted to the original end-user customer to be free from defects in
materials and workmanship. If it is determined by Labelmate that a product has failed under the terms of
this warranty, the product will be repaired or replaced at no charge to the customer. Labelmate reserves all
rights to determination of coverage and liability under this warranty. The warranty period for all new
Labelmate products is outlined below:
The warranty period for all products starts on the date purchased by the original end-user customer.
Warranty coverage is not transferable with ownership and will terminate immediately upon rental, resale or
any other change in ownership. This warranty does not cover repair to any product which is damaged, has
been modified, is missing parts, or has been opened or repaired by any unauthorised person. Use of any
unauthorised accessory or attachment will void coverage. Purchase documentation should be retained for
coverage verification.
In the event your product requires service, please contact the distributor you bought the product from. The
customer assumes responsibility for all cost and risk incurred in transport for service.
Labelmate makes no other warranty of any kind expressed or implied, or to suitability or fitness for a
particular purpose. No other person, agent or reseller is authorised to give any warranties on behalf of
Labelmate. Any obligation to warranty other than that specifically addressed above is hereby disclaimed.
Warranty Period
Products Covered
5 years
Label Rewinders
Label Unwinders
3 years
Label Counters (mechanical parts
only)
Label Slitters (mechanical parts
only)
Label Dispensers
Printer Mechanisms
1 year
Power Supply Modules
Counter modules
Encoders
Any products not specified above.
SPRL
290? Chauss2e de Ruisbroek, 1620 Drogenbos, BELGIUM
TEL: +32 2.375.69.60 FAX: +32 2.375.38.96 –
brussels@labelmate.com
www.labelmateeurope.com
Heavy-Duty "UCAT"
On-Demand Powered Label winderUn
• Dual Torque Range and Direction
Controls
• Constant Adjustable TorqueTM
"CAT" technology
• Adjustable Speed Control
• Precise Variable Torque Control
Remove all parts from the shipping container and verify contents.
PACKAGE CONTENTS:
• User Manual (this document)
• UCAT-40 Drive Unit
• Power Supply Module
• LABELMATE "Quick- -Locking Core Chuck Chuck" ™ Quick
• Allen Wrench
• Plastic Inner Flange Plate
• Control Arm with setscrews and shaft screw.
Retain the Shipping Container and Packaging for Storage and Transport
SPECIFICATIONS:
Weight of the machine: 12,9Kg.
Max. Label Roll Weight: 14Kg.
Max. Label Roll Diam: 400mm.
Start/Stop: ON/OFF/ON Direction Switch
Power Supply: Input: 220-240VAC -60Hz. –50
Output: 15V DC.
IMPORTANT INFORMATION:
• This product is a label winder. It is only to be used unwind labels of the un to
recommended dimensions and weight in an indoor, dry environment.
• The machine has to be unplugged before any manipulation.
• The machine is to be used on a flat surface, if the surface is not flat, it is to be fixed using
the holes in the base plate.
• Do not leave the power cable in a passageway.
• The ambient light of the working area needs to be sufficient to avoid any risk.
• The unwinder can be used in ambient temperatures of +2°C to 40°C.
• Connection of the machine to the power source must respect local and European
legislations.
SET-UP:
1. Install the Control Arm referring to the enclosed TA User Manual
2. Mount the 400-mm (16") diameter Flange Plate onto the Core Holder "Quick-Chuck"
using the screws provided.
3. Slide the and Flange Assembly onto the UCAT-40 Motor Shaft "Quick-Chuck"
allowing for clearance to the Chassis and Motor Screws. Tighten the Allen screw to
secure the and Flange Assembly onto the Motor. "Quick-Chuck"
4. Set the UCAT-40 in place near the label entrance path of the printer.
5. CAUTION: AVOID ACCIDENTS. THE UCAT-40 WEIGHS APPROXIMATELY 13KG,
SO CHOOSE ONLY A STURDY SURFACE ON WHICH TO SET THE UNIT.
6. The UCAT-40 is bi-directional. It can rewind labels in either direction.
7. Verify that the "DIRECTION" Switch on the UCAT-40 Control Panel is in the "OFF"
position.
8. Plug the Power Plug at the end of the wire on the AC Wall Transformer into the
UCAT-40 Power Input Jack. Plug the AC Transformer into an appropriate AC power
outlet.
9. The unit is now ready for use.
FOR YOUR SAFETY:
Switch off device before any manipulation.
POWER UNWINDING:
1. Place the "DIRECTION" Switch on the UCAT-40 Control Panel in the centre "OFF"
position.
2. Slide the roll of labels to be unwound on the Quick-Chuck.
3. Run the labels under the UCAT-40 Control Arm and into the printer.
4. Place the "DIRECTION" switch in the desired position to feed the labels into your
printer.
5. Place the "REWIND SLIT" Switch in the Rewind position and advance the –
"TORQUE" Control about 1/3 rotation from fully Counter-Clockwise as an initial
setting.
6. Start your printer and observe how the labels are being fed into the printer.
Adjust the "TORQUE" Control as needed to provide more or less unwind assistance. As
the printer uses the labels, the Control Arm will rise, causing the UCAT-40 to turn on and
feed more labels. As the UCAT-40 feeds more labels, the labels and the Control Arm will
drop down, turning off the UCAT-40 until more labels are needed as the Control Arm is
lifted again.
EXTERNAL HALT CONTROL:
An External Halt Control jack on the UCAT-3 is for use with external devices capable of
providing an open circuit halt command. A 3.5mm control cable is necessary for use (not
included).
With Pin 2 and Pin 3 of the External Halt Control circuit closed (connected together using
a 3.5mm dual circuit plug), the UCAT- will operate. When the External Circuit is opened, 3
the UCAT-3 will stop.
3.5mm “EXTERNAL HALT CONTROL” Stereo Plug (Dual Circuit Plug)
Contact CLOSED=RUN Contact OPEN=HALT
Pin 1 - No connection (NOT USED)
Pin 2 - Normally Closed (NC) contact
Pin 3 - Normally Closed (NC) contact return
WARNING!
This Product is for indoor use only.
Not for use in wet locations.
2 31

Produkt Specifikationer

Mærke: Labelmate
Kategori: Ikke kategoriseret
Model: UCAT-1-CHUCK

Har du brug for hjælp?

Hvis du har brug for hjælp til Labelmate UCAT-1-CHUCK stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Labelmate Manualer

Labelmate

Labelmate UCAT-40 Manual

6 August 2024
Labelmate

Labelmate CAT-4 Manual

6 August 2024
Labelmate

Labelmate UCAT-1-CHUCK Manual

6 August 2024
Labelmate

Labelmate S-100S Manual

6 August 2024
Labelmate

Labelmate CAT-4-ACH Manual

6 August 2024
Labelmate

Labelmate Count-200 Manual

6 August 2024
Labelmate

Labelmate Count-100 Manual

6 August 2024
Labelmate

Labelmate CAT-40G Manual

6 August 2024
Labelmate

Labelmate LD-100-U Manual

6 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Navman

Navman AUTO300 WIFI Manual

1 August 2025
Navman

Navman AUTO550 DUAL Manual

1 August 2025
Newline

Newline DV-15023H Manual

1 August 2025
Navman

Navman MiVue 720 Manual

1 August 2025
Etna

Etna HF2008 Manual

1 August 2025
Grundig

Grundig 40 VLE 7630 WP Manual

1 August 2025
Navman

Navman MiVue 600 DC Manual

1 August 2025
Navman

Navman MiVue 830DC Manual

1 August 2025
Navman

Navman MiVue 840 Manual

1 August 2025
Navman

Navman MiVue 880 DC Manual

1 August 2025