Labelmate CAT-40G Manual

Labelmate Ikke kategoriseret CAT-40G

Læs gratis den danske manual til Labelmate CAT-40G (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Labelmate CAT-40G, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Tension Arm for "CAT-TA" Rewinder

Control Arm for "UCAT-3"/"UCAT-40" Unwinders

• CAT-3-TA/CAT- -TA: On-40G

demand Rewinding Turns

Oﬀ When Labels Stop

Coming from Your Printer

• UCAT-3 / UCAT-40: On-

demand Unwinding Turns

On When Printer Needs

Labels

CAT-3- -STANDARD TA

UCAT- 40

SET-UP:

1. The Tension Arm/Control Arm is to be mounted vertically. UCAT-40:

CAT-3-TA / CAT- -TA:40G The Tension Arm can be mounted facing either right or

left, depending on which side the labels are coming from.

UCAT-3: The Control Arm can be mounted facing either right or left, depending on

which side the labels need to go to.

2. Remove and keep the large Screw from the end of the Tension/Control Arm Shaft

(the small Shaft below the main Motor Shaft).

3. Loosen the Set Screw at the end of the Tension/Control Arm and position the Arm

with the Set Screw facing the ﬂat on the Tension/Control Arm Shaft.

4. Tighten the Set Screw facing the ﬂat on the Shaft.

5. -insert and tighten the Tension/Control Arm Shaft Screw snugly into the Re

Tension/Control Arm Shaft.

The Unit is now ready for use.

USE POWER REWINDING (CATs): –

1. Run the label web to be rewound under the Rewinder Tension Arm and onto the take-

up label Core on the Rewinder.

2. Place the Rewinder DIRECTION switch in the desired position according to which

direction you want to rewind the labels.

3. Place the REWIND SLIT Switch in the REWIND position and set the TORQUE –

ADJUST about 1/3 rotation from fully CCW as an initial setting.

4. Start your printer and observe how the labels are being rewound.

5. Adjust the TORQUE Control as needed to provide more or less (faster or slower)

rewind power. As the Rewinder winds up the labels, the Tension Arm will rise,

eventually causing the Rewinder to turn oﬀ. As the printer feeds more labels that

need to be rewound, the labels and the Tension Arm will drop down, turning on the

Rewinder again.

6. A weight can be placed on the Tension Arm if desired to control the rewind web

tension.

USE POWER UNWINDING (UCATs): –

Refer to your Unwinder User Manual.

SPRL

290, Chaussée de Ruisbroek, 1620 Drogenbos, BELGIUM

TEL: +32 2.375.69.60 FAX: +32 2.375.38.96 –

brussels@labelmate.com

www.labelmateeurope.com

Produkt Specifikationer

Mærke:	Labelmate
Kategori:	Ikke kategoriseret
Model:	CAT-40G

Har du brug for hjælp?

Hvis du har brug for hjælp til Labelmate CAT-40G stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Labelmate Manualer

Labelmate UCAT-40 Manual

6 August 2024

Labelmate CAT-4 Manual

6 August 2024

Labelmate UCAT-1-CHUCK Manual

6 August 2024

Labelmate S-100S Manual

6 August 2024

Labelmate CAT-4-ACH Manual

6 August 2024

Labelmate Count-200 Manual

6 August 2024

Labelmate Count-100 Manual

6 August 2024

Labelmate CAT-40G Manual

6 August 2024

Labelmate LD-100-U Manual

6 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Leifheit TwistCut 23041 Manual

4 November 2025

Ikea KVISSLE 901.980.30 Manual

4 November 2025

Beverage-Air Horizon HRP2HC-1HG Manual

4 November 2025

Scheppach MR200-61 Manual

4 November 2025

Beverage-Air Horizon HF2HC-1S Manual

4 November 2025

Iogear SuperSpeed GFR304SD Manual

4 November 2025

EtherWAN EX42905 Manual

4 November 2025

ANCEL DP500 Manual

4 November 2025

Zotac GAMING GeForce RTX 2060 AMP Manual

4 November 2025

J-Tech Digital JTECH-EX-120M-UN-R Manual

4 November 2025