Labelmate Count-100 Manual

Labelmate Ikke kategoriseret Count-100

Læs gratis den danske manual til Labelmate Count-100 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Labelmate Count-100, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

MAINTENANCE:

Your COUNT-100 / COUNT- 200 requires no maintenance.

Product Limited Warranty

All Labelmate Products are warranted to the original end-user customer to be free from defects in

materials and workmanship. If it is determined by Labelmate that a product has failed under the terms of

this warranty, the product will be repaired or replaced at no charge to the customer. Labelmate reserves all

rights to determination of coverage and liability under this warranty. The warranty period for all new

Labelmate products is outlined below:

The warranty period for all products starts on the date purchased by the original end-user customer.

Warranty coverage is not transferable with ownership and will terminate immediately upon rental, resale or

any other change in ownership. This warranty does not cover repair to any product which is damaged, has

been modiﬁed, is missing parts, or has been opened or repaired by any unauthorised person. Use of any

unauthorised accessory or attachment will void coverage. Purchase documentation should be retained for

coverage veriﬁcation.

In the event your product requires service, please contact the distributor you bought the product from. The

customer assumes responsibility for all cost and risk incurred in transport for service.

Labelmate makes no other warranty of any kind expressed or implied, or to suitability or fitness for a

particular purpose. No other person, agent or reseller is authorised to give any warranties on behalf of

Labelmate. Any obligation to warranty other than that speciﬁcally addressed above is hereby disclaimed.

Warranty Period

Products Covered

5 years

Label Rewinders

Label Unwinders

3 years

Label Counters (mechanical parts

only)

Label Slitters (mechanical parts

only)

Label Dispensers

Printer Mechanisms

1 year

Power Supply Modules

Counter modules

Encoders

Any products not speciﬁed above.

SPRL

290, Chaussée de Ruisbroek, 1620 D , BELGIUM rogenbos

TEL: +32 2.375.69.60 FAX: +32 2.375.38.96 –

brussels@labelmate.com

www.labelmateeurope.com

Label Counter for use with CAT-3 Label Rewinders

• Digital Circuitry for Accuracy and

Repeatability.

• Pre-set Counter.

• Stops Rewinder when Count is reached.

Remove all parts from the shipping container and verify contents.

PACKAGE CONTENTS:

• User Manual (this document)

• COUNT-100 or COUNT-200 Counter Unit

• Power Supply Module

Retain the Shipping Container and Packaging for Storage and Transport

SPECIFICATIONS:

Weight of the machine: COUNT- COUNT- .100: 7,42Kg –200: 8,13Kg

Max. Label Roll Width: C-100: 170mm (6.7") C-200: 255mm (10"). –

Power Supply: Input: 220-240VAC -60Hz. Output: 12VDC –50

IMPORTANT INFORMATION:

• This product is a label counter. It is only to be used to count labels of the recommended

dimensions in an indoor, dry environment.

• The machine has to be unplugged before any manipulation.

• The machine is to be used on a ﬂat surface, if the surface is not ﬂat; it is to be fixed using

the holes in the base plate.

• Do not leave the power cable in a passageway.

• The ambient light of the working area needs to be suﬃcient to avoid any risk.

• The counter can be used in ambient temperatures of +2°C to 40°C.

• Connection of the machine to the power source must respect local and European

legislations.

PC-1 PRE-SET COUNTER SET-UP:

1. Verify that the AC/DC Adaptor “VOLT CHANGE SW.” is set to “ ” and plug 12

it into a suitable AC Power Outlet. Plug the Cord on the AC/DC Adaptor into

the Power Input Jack on the bottom of the Counter Display Module.

2. Plug the Control Cable (with 3.5mm plugs at each end) between the Output

Jack on the bottom of the Counter Display Module and the “EXTERNAL

HALT CONTROL” jack on the CAT-2 Label Rewinder.

3. The Counter is pre-programmed as a Preset Count- Counter. Press each up

of the 6-digits for the count desired. This is the number of labels you wish

to pass through the Label Sensor before the Counter issues a “HALT”

command to the CAT-2 Label Rewinder.

4. Pull a short strip of labels back and forth through the Label Sensor Gap and

observe the count on the Counter increasing. When the preset number of

labels is reached, the PC-1 Counter will issue a Halt Command for the CAT-

2 Label Rewinder to stop. Pressing “RESET” will reset the count and restart

the CAT- 2.

5. See the included detailed manual for the Pre-set Counter itself for other

Counter options.

FOR YOUR SAFETY:

Switch oﬀ device before any manipulation.

COUNTER USE:

1. Place the COUNT-100 or COUNT-200 Label Counter so that it is

perpendicular to the label web.

2. Observe the Paper Path Label on the Counter: Feed the label web under the

metal Rotating Paper Guide and over the Nylon Fixed Paper Guide.

3. Adjust the position of the rings on the Rotating and Fixed Paper Guides to

the width of your label web. Only finger tighten the screws. The labels must

pass through the black sensor slot between the round Paper Guides.

4. Aﬃx the label web to the label rewind core on the Label Rewinder.

5. The Counter will count the number of labels passing through the sensor air

gap.

NOTE: If you observe erratic counting, clean the Optical Sensor with isopropyl

alcohol.

INTERNAL CIRCUIT PROTECTION:

The COUNT-100 and COUNT-200 Label Counters have an internal device for

circuit protection. There are no user serviceable parts inside. In the event of

operational problems, please contact LABELMATE for assistance.

WARNING!

This Product is for indoor use only.

Not for use in wet locations.

Produkt Specifikationer

Mærke:	Labelmate
Kategori:	Ikke kategoriseret
Model:	Count-100

Har du brug for hjælp?

Hvis du har brug for hjælp til Labelmate Count-100 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Labelmate Manualer

Labelmate UCAT-40 Manual

6 August 2024

Labelmate CAT-4 Manual

6 August 2024

Labelmate UCAT-1-CHUCK Manual

6 August 2024

Labelmate S-100S Manual

6 August 2024

Labelmate CAT-4-ACH Manual

6 August 2024

Labelmate Count-200 Manual

6 August 2024

Labelmate Count-100 Manual

6 August 2024

Labelmate CAT-40G Manual

6 August 2024

Labelmate LD-100-U Manual

6 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

T'nB VINEKIT Manual

16 September 2025

T'nB PADA36W Manual

16 September 2025

T'nB TCUNSAM Manual

16 September 2025

Ikea HATTHOLMEN 105.084.80 Manual

16 September 2025

T'nB MHFIXDUAL Manual

15 September 2025

T'nB MHFLEX Manual

15 September 2025

T'nB ANIN02 Manual

15 September 2025

T'nB TCUNVES Manual

15 September 2025

T'nB NBSTANDFLEX Manual

15 September 2025

T'nB TCUN01 Manual

15 September 2025