Legrand RT50W Manual

Legrand Ikke kategoriseret RT50W

Læs gratis den danske manual til Legrand RT50W (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 58 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 29.5 anmeldelser. Har du et spørgsmål om Legrand RT50W, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Wattstopper
®
Time Switch – 7- Button Preset
Installation Instructions • Instructions d’Installation • Instrucciones de Instalación
No: 24211 – 09/16 rev. 1
Catalog Number • Numéro de Catalogue • Número de Catálogo: RT-50
Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China
SPECIFICATIONS
Voltage .................................................. 120VAC, 60HZ
Load (Single Pole Circuit)
Incandescent or fluorescent lamp ....0 – 600 Watt
Fan Motor .................................................... 1/6HP
Time Delay ........................ 1, 5, 10, 20, 30, 60 minutes
Environment ......................................... Indoor use only
Operating Temperature .........32° to 131°F (0° to 55°C)
Humidity ...............................95% RH, non-condensing
Tools Needed
Insulated Screwdriver
Wire Strippers
DESCRIPTION AND OPERATION
The RT-50 is a time switch that turns OFF the connected
light or fan when the selected time expires. The light
behind the ON/OFF button illuminates while the switch
is OFF. One of the time button indicators is always lit to
indicate the last used timer.
Manual ON
Turn ON the connected light or fan by pressing the desired
time button, or the ON/OFF button. If you press the ON/
OFF button, it activates the timer that was last used.
Manual OFF
While a timer is active, you can press the ON/OFF button
to turn OFF the connected light or fan without delay.
Changing the selected time
If you decide that you need more or less time than you
originally selected, restart the time switch by pressing the
button that matches the amount of time you think you’ll need.
INSTALLATION
1. Prepare the switch box.
After the power is turned OFF at the circuit breaker box, remove the existing wall plate and mounting screws. Pull
the old switch out from the wall box.
2. Identify the type of circuit.
In a Single Pole Circuit (see Fig. 1), two single wires connect to two screws on the existing
switch. A ground wire may also be present and connected to a ground terminal on the old
switch. A neutral wire should also be present in the wall box.
NOTE: If a proper ground is not available, consult with a qualified electrician before
continuing installation.
Only connect the RT-50 to a Single Pole Circuit. The RT-50 is not suitable for 3-way
switching. If the existing wiring does not match the description for a Single Pole Circuit, you
should consult with a qualified electrician.
3. Prepare the Wires.
Tag the wires currently connected to the existing switch, so that they can be identified later.
Disconnect the wires. Make sure the insulation is stripped off the wires to expose their
copper cores to the length indicated by the “Strip Gage,” in Fig. 2 (approximately 1/2 inch).
4. Wire the time switch.
Twist the existing wires together with the wire leads on the time switch as indicated in the
drawing. Cap them securely using the wire nuts provided. See Fig 3 on the next page.
• Connect the green or non-insulated (copper) GROUND wire from the circuit to the GROUND terminal
on the RT-50.
• Connect the power wire from the circuit (HOT) to the black wire on the RT-50.
• Connect the power wire to the lamp or fan (LOAD) to the red wire on the RT-50.
• Connect the NEUTRAL wires from the circuit to the white wire on the RT-50.
5. Put the RT-50 in the wall box with the time selection buttons positioned above the ON/OFF button.
Secure it to the wall box with the screws provided.
6. Install cover plates.
Install industry standard decorator wall switch cover plate (not
included).
WARNING: TURN THE POWER OFF AT THE
CIRCUIT BREAKER BEFORE WIRING.
WARNING: CONNECTING A PROPER
GROUND TO THE TIME SWITCH PROVIDES
PROTECTION AGAINST ELECTRICAL SHOCK
IN THE EVENT OF CERTAIN FAULT CONDITIONS.
Strip Gauge
1/2"
12.7 mm
Fig. 2: Wire Stripping
Ground
HOT (power from
circuit box)
LOAD
(power
to lamp)
NEUTRAL
Fig. 1: Typical Single Pole
Switch Wiring

Produkt Specifikationer

Mærke: Legrand
Kategori: Ikke kategoriseret
Model: RT50W

Har du brug for hjælp?

Hvis du har brug for hjælp til Legrand RT50W stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Legrand Manualer

Legrand

Legrand 352500 Manual

15 Juli 2025
Legrand

Legrand 093023 Manual

7 Juli 2025
Legrand

Legrand 093020 Manual

7 Juli 2025
Legrand

Legrand 310877 Manual

7 Juli 2025
Legrand

Legrand 093021 Manual

28 Marts 2025
Legrand

Legrand Ensto Pro EVF200 Manual

1 Oktober 2024
Legrand

Legrand Ensto Wallbox EVB200 Manual

1 Oktober 2024
Legrand

Legrand 092716 Manual

1 Oktober 2024
Legrand

Legrand Pass & Seymour RSWV153 Manual

6 September 2024
Legrand

Legrand RT50W Manual

28 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

PAG

PAG Mini link 6002 Manual

4 November 2025
Wamsler

Wamsler K128 Manual

4 November 2025
Sonifex

Sonifex Redbox RB-DSD8 Manual

4 November 2025
Zotac

Zotac ZBOX MI561 nano Manual

4 November 2025
MuxLab

MuxLab 500800-RX Manual

4 November 2025
Hawke

Hawke Laser/LED Foregrip Manual

4 November 2025
Wooden Camera

Wooden Camera 213900 Manual

4 November 2025
Chauvet

Chauvet Freedom Flex Stick Battery Manual

4 November 2025
DS18

DS18 VOC8LD-PK Manual

4 November 2025
Sony

Sony XDCAM PXW-Z90 Manual

4 November 2025