LiftMaster PPK3M Manual

LiftMaster Ikke kategoriseret PPK3M

Læs gratis den danske manual til LiftMaster PPK3M (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om LiftMaster PPK3M, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
PASSPORT MAX REMOTE CONTROLS
To prevent possible SERIOUS INJURY or DEATH from a moving gate
or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER
permit children to operate, or play with remote controls.
• Activate gate or door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
Model PPV3M Models PPK3M and PPK3PHM
INTRODUCTION
The Passport MAX is a credentialed remote control. The Passport MAX
remote control is a versatile remote control that can be used on access
control systems, commercial door operators, gate operators, residential
garage door openers, and external receivers (Models PPWR, 850LM,
860LM, STAR1000) that use Security+ 2.0® or Security+ (315 Mhz and
390 Mhz) technology. The additional buttons on the remote control can
be programmed to operate up to 3 additional devices such as garage
door openers, light controls, gate operators or access control systems.
NOTE: Passport MAX credentialed remote controls are not compatible
with CPWR, CPWR3, RFMODKT, and RFMODKT3 Passport products.
NOTE: The images are for reference and your product may look different.
PROGRAMMING
Depending on your product, the LEARN button or LCD menu will be used
to program the remote control. 
If programming to an access control system or gated entry, contact your
property manager or LiftMaster® dealer for assistance with any
programming or operating instructions.
OPTION 1 – SECURITY+2.0 ® PRODUCTS
1. Locate the LEARN button on your product or the PROGRAM button on
the LCD (if applicable).
2. Press and release the yellow LEARN button on your product or the
PROGRAM button on the LCD. NOTE: The button color on commercial
products may vary.
3. Press andhold the remote control button you wish to use untilyour
product’s programming LED turns off orthe lights flash on your
product.
4. To test, press the programmed button on the remote control and the
product will activate.
OPTION 2 – SECURITY+ PRODUCTS (315 Mhz and 390 Mhz)
1. Locate the Program
button on the remote
control.
2. To enter the programming mode on the remote control, press the
program button until the LED on the front of the remote control turns
on.
3. Press and release the remote control button you wish to use:
• 2 times if your product is 315 MHz (Purple LEARN button)
• 3 times if your product is 390 MHz (Red/Orange LEARN button)
NOTE: The button color on commercial products may vary.
4. Exit programming mode by pressing any remote control button except
the button that was just programmed.
5. For LEARN button:
• Press and release the LEARN button on your product
For LCD:
• Press the navigation button below
“MENU” to view the Features menu on
the LCD. Use the navigation buttons to
scroll to “PROGRAM”. Select
“REMOTE” to program from the
program menu.
6. Press andhold the remote control button you programmed in Step 3
untilyour product’s programming LED turns off orthe lights flash on
your product.
7. To test, press the programmed button on the remote control and the
product will activate.
Program Button
WARNING: This product can expose you to chemicals including
lead, which are known to the State of California to cause cancer or
birth defects or other reproductive harm. For more information go
to www.P65Warnings.ca.gov
ONE YEAR LIMITED WARRANTY
The Chamberlain Group, Inc. warrants to the first consumer purchaser of
this product that it is free from defect in materials and/or workmanship
for a period of 1 year from the date of purchase.
REPLACEMENT PARTS
3V CR2032 Lithium battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10A20
Visor Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29B137
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)this device
must accept any interference received, including interference that may cause undesired operation.
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
To reduce risk of fire, explosion or chemical burn:
• Replace ONLY with 3V CR2032 coin batteries.
• DO NOT recharge, disassemble, heat above 212° F (100° C) or
incinerate.
KEY CHAIN REMOTE
Pry open the case with a
screwdriver blade.
VISOR REMOTE
Pry open the case first in the
middle (1), then at each side
(2 and 3) with the visor clip.
1
2
3
Battery
Battery
PROGRAMMING (CONTINUED)
OPTION 3 – RE-PROGRAMMING FOR SECURITY+2.0 ® PRODUCTS
1. Locate the Program button on the remote control.
2. To enter the programming mode on the remote control, press the
program button until the LED on the front of the remote control turns
on.
3. Press and release the remote control button you wish to use:
• 1 time for SECURITY+2.0® product (Yellow LEARN button).
4. Exit programming mode by pressing any remote control button except
the button that was just programmed.
5. Press and release the yellow LEARN button on your product or the
PROGRAM button on the LCD. NOTE: The button color on commercial
products may vary.
6. Press andhold the remote control button you programmed in Step 3
untilyour product’s programming LED turns off orthe lights flash on
your product.
7. To test, press the programmed button on the remote control and the
product will activate.
HOW TO USE THE REMOTE CONTROL
Press and hold the button down until the door or gate starts to move.
For key chain remote controls with a proximity sensor, hold the remote
control 1-2" away from the reader face and wait for a confirmation beep
or LED from the reader. Operation of the proximity sensor varies
depending on the access control system. For additional information refer
to the owner’s manual for the access control system.
THE REMOTE CONTROL BATTERY
To replace battery, open the case as shown. Insert battery positive side
up (+). Replace the battery with only 3V CR2032 coin cell battery.
Dispose of old battery properly.
1-800-528-9131
LiftMaster.com

Produkt Specifikationer

Mærke: LiftMaster
Kategori: Ikke kategoriseret
Model: PPK3M

Har du brug for hjælp?

Hvis du har brug for hjælp til LiftMaster PPK3M stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret LiftMaster Manualer

LiftMaster

LiftMaster 041-0405-000 Manual

15 Juni 2025
LiftMaster

LiftMaster LMHNTG Manual

4 September 2024
LiftMaster

LiftMaster CAPXSTKPL Manual

3 September 2024
LiftMaster

LiftMaster BG790 Manual

3 September 2024
LiftMaster

LiftMaster 64LM Manual

3 September 2024
LiftMaster

LiftMaster CAPXSHOOD Manual

28 August 2024
LiftMaster

LiftMaster myQ-SGC2WCH Manual

21 August 2024
LiftMaster

LiftMaster CAPXS Manual

21 August 2024
LiftMaster

LiftMaster MGJ5011U Manual

21 August 2024
LiftMaster

LiftMaster LMWEKITU Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Playtive

Playtive IAN 332975 Manual

16 Juni 2025
Playtive

Playtive HG05527 Manual

16 Juni 2025
Philips

Philips 75PUH6393 Manual

16 Juni 2025
Foster

Foster Slimline FSL400L Manual

16 Juni 2025
Playtive

Playtive HG04098 Manual

16 Juni 2025
Aiphone

Aiphone JPW-BA Manual

16 Juni 2025
Life On Products

Life On Products LCAF020 Manual

16 Juni 2025
Hager

Hager CEA263U Manual

16 Juni 2025
Moulinex

Moulinex Illico DJE241 Manual

16 Juni 2025
Foster

Foster Slimline FSL800M Manual

16 Juni 2025