Luxul XMS-1010P Manual

Luxul Skifte XMS-1010P

Læs gratis den danske manual til Luxul XMS-1010P (8 sider) i kategorien Skifte. Denne vejledning er vurderet som hjælpsom af 50 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 25.5 anmeldelser. Har du et spørgsmål om Luxul XMS-1010P, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Fo ld Fo ld Fo ld

READ ME FIRST

QUICK INSTALL GUIDE

10-Port/8 PoE+ Gigabit

Managed Switch

XMS-1010P

Includes:



XMS-1010P 10-Port/8 PoE+ Gigabit Managed Switch



Rack Mount Kit



Rubber Feet



Power Cord

SETUP AND CONFIGURATION

Physical Installation

The XMS-1010P can be rack-mounted or used as a desktop switch. Install the

XMS-1010P in a stable/safe place to avoid any possible damage. Make sure there

is adequate space around the XMS-1010P for ventilation and proper heat dissi-

pation; Luxul recommends at least 4-6 inches around all sides. Avoid placement

in direct sunlight. Do not place heavy articles on the XMS-1010P and verify the

ground connection of the outlet is functioning properly.

Desktop/Shelf Installation

For desktop/shelf installation, attach the four rubber feet to the corner inden-

tations on the bottom of the XMS-1010P, then place the switch horizontally on

a solid, level platform.

Rack Installation

Use the included L brackets for convenient installation in a 19-inch server or

audio rack. As shown below, use four screws to attach the L-shaped brackets

on either sides of the XMS-1010P, and horizontally insert the switch into the

rack. Use your desired hardware to ax the switch supports to the rack.

Attach feet for desktop installation Install brackets for rack-mounting

Connecting Ethernet and Power

Ethernet and Power Connections

Use any RJ-45 to connect the XMS-1010P to an Ethernet-enabled device,

including servers, routers or other switches. No crossover cable is necessary.

The XMS-1010P supports 10/100/1000 Mbps Ethernet; 10/100 Mbps half/

full-duplex mode and 1000 Mbps full-duplex mode. All ten RJ-45 ports

support Auto MDI/MDIX and can be used as ordinary ports or as Uplink

ports. Ports 1-8 are PoE+ and are enabled by default.

Use the included power cable to connect the XMS-1010P to a surge protect-

ed outlet. The AC input socket and a power switch are on the rear panel.

The built-in power supply supports 100~240VAC at 50/60Hz.

Network Cabling

Luxul recommends Category-5, super Category-5 or Category-6 unshielded

twisted pair (CAT5/CAT5e/CAT6 UTP). To ensure best performance and

stable data transmission at 1000 Mbps, use Category-6 shielded twisted pair.

c CAUTION: Multiple Uplink channels can create loops, resulting in

network failure. Ensure only one Uplink channel exists

between switches or between the XMS-1010P and a router.

n NOTE: When powering up, the port LEDs corresponding to the opti-

cal interface may take a moment to initialize. This is normal

as the XMS-1010P initialization and startup completes.

n NOTE: The XMS-1010P has an internal 130W power supply. For

optimal switch performance, do not exceed 115W combined

consumption of all external PoE devices.

Sales

801-822-5450

sales@luxul.com

Technical Support

801-822-5450

support@luxul.com

LUX-QIG-XMS-1010P-v7 04131712

No part of this document may be modiﬁed or adapted in any way, for any purposes without permission

in writing from Luxul. The material in this document is subject to change without notice. Luxul reserves

the right to make changes to any product to improve reliability, function, or design. No license is granted,

either expressly or by implication or otherwise under any Luxul intellectual property rights. An implied

license only exists for equipment, circuits and subsystems contained in this or any Luxul product.

Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other trademarks and

registered trademarks are property of their respective holders.

Fo ld Fo ld Fo ld

READ ME FIRST

QUICK INSTALL GUIDE

10-Port/8 PoE+ Gigabit

Managed Switch

XMS-1010P

Includes:



XMS-1010P 10-Port/8 PoE+ Gigabit Managed Switch



Rack Mount Kit



Rubber Feet



Power Cord

SETUP AND CONFIGURATION

Physical Installation

The XMS-1010P can be rack-mounted or used as a desktop switch. Install the

XMS-1010P in a stable/safe place to avoid any possible damage. Make sure there

is adequate space around the XMS-1010P for ventilation and proper heat dissi-

pation; Luxul recommends at least 4-6 inches around all sides. Avoid placement

in direct sunlight. Do not place heavy articles on the XMS-1010P and verify the

ground connection of the outlet is functioning properly.

Desktop/Shelf Installation

For desktop/shelf installation, attach the four rubber feet to the corner inden-

tations on the bottom of the XMS-1010P, then place the switch horizontally on

a solid, level platform.

Rack Installation

Use the included L brackets for convenient installation in a 19-inch server or

audio rack. As shown below, use four screws to attach the L-shaped brackets

on either sides of the XMS-1010P, and horizontally insert the switch into the

rack. Use your desired hardware to ax the switch supports to the rack.

Attach feet for desktop installation Install brackets for rack-mounting

Connecting Ethernet and Power

Ethernet and Power Connections

Use any RJ-45 to connect the XMS-1010P to an Ethernet-enabled device,

including servers, routers or other switches. No crossover cable is necessary.

The XMS-1010P supports 10/100/1000 Mbps Ethernet; 10/100 Mbps half/

full-duplex mode and 1000 Mbps full-duplex mode. All ten RJ-45 ports

support Auto MDI/MDIX and can be used as ordinary ports or as Uplink

ports. Ports 1-8 are PoE+ and are enabled by default.

Use the included power cable to connect the XMS-1010P to a surge protect-

ed outlet. The AC input socket and a power switch are on the rear panel.

The built-in power supply supports 100~240VAC at 50/60Hz.

Network Cabling

Luxul recommends Category-5, super Category-5 or Category-6 unshielded

twisted pair (CAT5/CAT5e/CAT6 UTP). To ensure best performance and

stable data transmission at 1000 Mbps, use Category-6 shielded twisted pair.

c CAUTION: Multiple Uplink channels can create loops, resulting in

network failure. Ensure only one Uplink channel exists

between switches or between the XMS-1010P and a router.

n NOTE: When powering up, the port LEDs corresponding to the opti-

cal interface may take a moment to initialize. This is normal

as the XMS-1010P initialization and startup completes.

n NOTE: The XMS-1010P has an internal 130W power supply. For

optimal switch performance, do not exceed 115W combined

consumption of all external PoE devices.

Sales

801-822-5450

sales@luxul.com

Technical Support

801-822-5450

support@luxul.com

LUX-QIG-XMS-1010P-v7 04131712

No part of this document may be modiﬁed or adapted in any way, for any purposes without permission

in writing from Luxul. The material in this document is subject to change without notice. Luxul reserves

the right to make changes to any product to improve reliability, function, or design. No license is granted,

either expressly or by implication or otherwise under any Luxul intellectual property rights. An implied

license only exists for equipment, circuits and subsystems contained in this or any Luxul product.

Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other trademarks and

registered trademarks are property of their respective holders.

Produkt Specifikationer

Mærke:	Luxul
Kategori:	Skifte
Model:	XMS-1010P
Vekselstrømsindgangsspænding:	100 - 240 V
Vekselstrømsindgangsfrekvens:	50 - 60 Hz
Bredde:	292 mm
Dybde:	178 mm
Højde:	44.5 mm
Vægt:	1800 g
Produktfarve:	Sort, sølv
Relativ luftfugtighed ved drift (H-H):	10 - 90 %
Driftstemperatur (T-T):	0 - 40 °C
Ethernet LAN-datahastigheder:	10,100,1000 Mbit/s
Hurtig start guide:	Ja
Kabler inkluderet:	Vekselstrøm
Certificering:	FCC, IC, CE, RoHS, EN60950
Netværksstandarder:	IEEE 802.1D, IEEE 802.1p, IEEE 802.3, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Servicekvalitet support (QoS):	Ja
LED-indikatorer:	Activity, Link, PoE, Power
Fuld duplex:	Ja
Strøm over Ethernet (PoE):	Ja
Switch-type:	Administreret
Total Power over Ethernet (PoE):	130 W
Power over Ethernet plus (PoE+) porte, antal:	8
VLAN understøttelse:	Ja
Antal VLAN'er:	4094
Vituelle LAN funktioner:	Port-based VLAN
Basis omskiftning RJ-45 Ethernet porte, antal:	10
Basis omskiftning RJ-45 Ethernet porttype:	Gigabit Ethernet (10/100/1000)
MAC adresselabel:	- entries
Switch kapacitet:	- Gbit/sek.
Stativ-montering:	Ja
Gigabit Ethernet (kobber) porte, antal:	10
Strømstik:	DC-in-stik
Strømforsyning inkluderet:	Ja
Rack monteringskit:	Ja
Understøttede kabeltyper:	Cat5, Cat5e, Cat6
Algoritmer for køplanlægning:	Priority queuing (PQ), Weighted Round Robin (WRR)
Power over Ethernet (PoE) -type understøttet:	PoE+