Luxul XMS-1208P Manual

Luxul Skifte XMS-1208P

Læs gratis den danske manual til Luxul XMS-1208P (8 sider) i kategorien Skifte. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Luxul XMS-1208P, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
Fo ld Fo ld Fo ld
READ ME FIRST
QUICK INSTALL GUIDE
12-Port/8 PoE+ Gigabit
Managed Switch
XMS-1208P
Includes:
XMS-1208P 12-Port/8 PoE+ Switch
Rack Mount Kit
Rubber Feet
Power Cord
INSTALLATION AND SETUP
1
Physical Installation
The XMS-1208P can easily be installed in a standard 19” rack. Two mounting ears
are included for installing and stabilizing the switch. When attaching the mounting
ears and installing the switch in a rack, please refer to the following illustration:
Rack-mounting the XMS-1208P
Use the included screws to attach the mounting ears to each side
of the switch.
Mount the switch in the rack with the LEDs facing outwards. Be sure the
switch is level and properly secured in the rack.
Desktop Setup
For use as a desktop device, position and apply the included rubber feet to the
bottom of the XMS-1208P.
2
Connecting Ethernet and Power
Ethernet and Power Connections
Use one of the ten Ethernet ports to connect the XMS-1208P to any Ethernet-
enabled device, including servers, routers, or other switches. No crossover cable
is necessary.
The XMS-1208P supports 10/100/1000 Mbps Ethernet; 10/100 Mbps half/
full-duplex mode and 1000 Mbps full-duplex mode. Ports 1-8 are PoE+ and
are enabled by default. Ports 9 and 10 are Gigabit Ethernet only (non PoE),
while ports 11 and 12 are Gigabit SFP ports.
Use the included power cable to connect the XMS-1208P to a surge-
protected outlet. The AC input socket is on the rear panel. The built-in
power supply supports 100~240VAC at 50-60Hz.
Network Cabling
Luxul recommends at least Cat-5e unshielded twisted pair (CAT5e UTP)
cabling. To ensure best performance and stable data transmission at 1000
Mbps, use Category-6 unshielded twisted pair (CAT6 UTP).
If you intended to use optical fiber to extend the network beyond the 300-
foot limit of twisted pair Ethernet, SFP modules are required (not included).
c CAUTION: Multiple Uplink channels can create loops, resulting in
network failure. Ensure only one Uplink channel exists
between switches or between the XMS-1208P and a router.
n NOTE: When powering up, the port LEDs may take a moment to
initialize. This is normal as the XMS-1208P initialization and
startup sequence completes.
n NOTE: The XMS-1208P has an internal 130W power supply. Do not
exceed 25.5W each or 130W combined consumption of all
external PoE devices.
Sales
P: 801-822-5450
E: sales@luxul.com
Technical Support
P: 801-822-5450 Option 3
E: support@luxul.com
LUX-QIG-XMS-1208P-v1 08281810
Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any purposes without permission
in writing from Luxul. The material in this document is subject to change without notice. Luxul reserves
the right to make changes to any product to improve reliability, function, or design. No license is granted,
either expressly or by implication or otherwise under any Luxul intellectual property rights. An implied
license only exists for equipment, circuits and subsystems contained in this or any Luxul product.
© Copyright 2018 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and
Simply Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other
trademarks and registered trademarks are property of their respective holders.
Fo ld Fo ld Fo ld
READ ME FIRST
QUICK INSTALL GUIDE
12-Port/8 PoE+ Gigabit
Managed Switch
XMS-1208P
Includes:
XMS-1208P 12-Port/8 PoE+ Switch
Rack Mount Kit
Rubber Feet
Power Cord
INSTALLATION AND SETUP
1
Physical Installation
The XMS-1208P can easily be installed in a standard 19” rack. Two mounting ears
are included for installing and stabilizing the switch. When attaching the mounting
ears and installing the switch in a rack, please refer to the following illustration:
Rack-mounting the XMS-1208P
Use the included screws to attach the mounting ears to each side
of the switch.
Mount the switch in the rack with the LEDs facing outwards. Be sure the
switch is level and properly secured in the rack.
Desktop Setup
For use as a desktop device, position and apply the included rubber feet to the
bottom of the XMS-1208P.
2
Connecting Ethernet and Power
Ethernet and Power Connections
Use one of the ten Ethernet ports to connect the XMS-1208P to any Ethernet-
enabled device, including servers, routers, or other switches. No crossover cable
is necessary.
The XMS-1208P supports 10/100/1000 Mbps Ethernet; 10/100 Mbps half/
full-duplex mode and 1000 Mbps full-duplex mode. Ports 1-8 are PoE+ and
are enabled by default. Ports 9 and 10 are Gigabit Ethernet only (non PoE),
while ports 11 and 12 are Gigabit SFP ports.
Use the included power cable to connect the XMS-1208P to a surge-
protected outlet. The AC input socket is on the rear panel. The built-in
power supply supports 100~240VAC at 50-60Hz.
Network Cabling
Luxul recommends at least Cat-5e unshielded twisted pair (CAT5e UTP)
cabling. To ensure best performance and stable data transmission at 1000
Mbps, use Category-6 unshielded twisted pair (CAT6 UTP).
If you intended to use optical fiber to extend the network beyond the 300-
foot limit of twisted pair Ethernet, SFP modules are required (not included).
c CAUTION: Multiple Uplink channels can create loops, resulting in
network failure. Ensure only one Uplink channel exists
between switches or between the XMS-1208P and a router.
n NOTE: When powering up, the port LEDs may take a moment to
initialize. This is normal as the XMS-1208P initialization and
startup sequence completes.
n NOTE: The XMS-1208P has an internal 130W power supply. Do not
exceed 25.5W each or 130W combined consumption of all
external PoE devices.
Sales
P: 801-822-5450
E: sales@luxul.com
Technical Support
P: 801-822-5450 Option 3
E: support@luxul.com
LUX-QIG-XMS-1208P-v1 08281810
Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any purposes without permission
in writing from Luxul. The material in this document is subject to change without notice. Luxul reserves
the right to make changes to any product to improve reliability, function, or design. No license is granted,
either expressly or by implication or otherwise under any Luxul intellectual property rights. An implied
license only exists for equipment, circuits and subsystems contained in this or any Luxul product.
© Copyright 2018 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and
Simply Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other
trademarks and registered trademarks are property of their respective holders.

Produkt Specifikationer

Mærke: Luxul
Kategori: Skifte
Model: XMS-1208P

Har du brug for hjælp?

Hvis du har brug for hjælp til Luxul XMS-1208P stil et spørgsmål nedenfor, og andre brugere vil svare dig


Skifte Luxul Manualer

Luxul

Luxul XMS-5248P Manual

13 Januar 2025
Luxul

Luxul AMS-2624P Manual

13 Januar 2025
Luxul

Luxul XGS-1005 Manual

13 Januar 2025
Luxul

Luxul AGS-1008M Manual

13 Januar 2025
Luxul

Luxul XMS-1208P Manual

13 Januar 2025
Luxul

Luxul XMS-7048P Manual

13 Januar 2025
Luxul

Luxul AMS-2600 Manual

13 Januar 2025
Luxul

Luxul AGS-1016 Manual

13 Januar 2025
Luxul

Luxul XMS-2624P Manual

13 Januar 2025
Luxul

Luxul AMS-1816P Manual

13 Januar 2025

Skifte Manualer

Nyeste Skifte Manualer

Lancom

Lancom GS-2412 Manual

4 April 2025
Lancom

Lancom GS-2412P Manual

4 April 2025
Lancom

Lancom GS-2426 Manual

4 April 2025
Hager

Hager ARF970D Manual

3 April 2025
Hager

Hager ARF920D Manual

3 April 2025
Roline

Roline 14.01.3579 Manual

2 April 2025
Fantini Cosmi

Fantini Cosmi B12BN Manual

1 April 2025
Fantini Cosmi

Fantini Cosmi B12DN Manual

1 April 2025
Fantini Cosmi

Fantini Cosmi B12GN Manual

1 April 2025
Fantini Cosmi

Fantini Cosmi B12HN Manual

1 April 2025