Maxwell MX-25401 Manual

Maxwell Multimeter MX-25401

Læs gratis den danske manual til Maxwell MX-25401 (24 sider) i kategorien Multimeter. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Maxwell MX-25401, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/24

DIGITAL MULTIMETER PEN STYLE WITH LED

LAMPDIGITAL-MULTIMETER

DIGITALES MULTIMETER MIT LED-LAMPE

DIGITÁLIS MULTIMÉTER LED LÁMPÁVAL

DIGITÁLNÍ MULTIMETR S LED LAMPOU

DIGITÁLNY MULTIMETER S LED LAMPOU

MULTIMETR CYFROWY Z LAMPĄ LEDDIGITÁLNY

MULTIMETRU DIGITAL CU LED

25401

U Mser anUal

GebraUchsanweisUnG

használati Utasítás

návod k poUžití

návod na poUžitie

instrUkcja obsłUGi

ManUal de Utilizare

w !arninG

To avoid electric shock and other injury please pay

attention to the following:

• Do not use the device if it is damaged. Check the

cover of the device before use. Pay extra attention to

the insulation near the connectors.

• Check the connecting cables, their insulation. If the

cables or the connectors are defective, replace them

or do not use the device.

• Do not use the device if it operates improperly. If you

have doubts, take the device to a service station.

• Do not use the device near explosive materials (gases,

vapors, powders)

• Do not measure higher voltage on the device than

indicated, not between the measuring connectors or

between one of them and the earthing.

• Verify the operation of the device before usage by

measuring a known voltage.

• When measuring current, turn o the device before

connecting it to the circuit. Make sure that the device

is connected to the measured circuit serially.

• Only use the designated spare parts to repair the

device.

• When measuring above 30 V AC RMS, 42 V peak, or 60

V DC voltage pay extra atenntion, because there is a

risk of electric shock.

• When measuring, connect the measuring pin on

the wire rst, and then the one on the device to the

circuit.

• Do not use the device if the battery container lid or

any part of the cover is missing.

• To avoid incorrect measuring results, electric shock

and injury, replace the batteries right after the low

battery symbol is lit on the display.

Further risks: If any of the measuring points are

connected to a dangerous voltage, this voltage may

appear on the other measuring pin as well.

w !arninG

To avoid damage to the device or the measured

circuit, please note the following:

• Disconnect the power cord and discharge the high

capacity capacitors before measuring resistance,

diode or continuity.

• Use the proper mode and threshold for measurement.

• Before measuring current always check the fuses and

turn o the measured circuit before connecting the

device to it.

• Remove the device from the measured circuit before

changing measuring mode with the switch.

• Remove the device from the measured circuit before

taking o the cover.

G eneral description

The MP-25 401 is a small size 3 1/2 digit automatic

threshold switching digital multimeter which enables

measuring constant and alternating voltages, alternate

and direct currents, resistance, diode and circuit

continuity.

The device has the following functions:

• Automatic nullication

• Polarity display

• Holding the measured data

• Overload display

• Automatic o switch

• Lamp function

e slectric yMbols

AC (alternate current)

DC (direct current)

Important security information. Read the

manual.

Dangerous voltage

Earthing

Fuse

Complies to EU directives

Double isolation

Low batter power

Diode

s s dpecial yMbols on the isplay

For security reasons, the following are displayed on

the device:

600V

MAX

To avoid electric shock and damage

to the device, do not connect voltage

bigger than 600V between the

measuring pins.

General danger indication. Follow the

instructions in the manual.

600 V DC

600 V AC

200 mA

MAX

The max. amount of the voltage

measurable by the device is 600V DC or

600VAC. The max. measurable current

is 200mA DC or AC.

When measuring high voltage always

take special care. Do not touch any

measuring pins by hand.

Double isolation

Produkt Specifikationer

Mærke:	Maxwell
Kategori:	Multimeter
Model:	MX-25401

Har du brug for hjælp?

Hvis du har brug for hjælp til Maxwell MX-25401 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Multimeter Maxwell Manualer

Maxwell MX-25103 Manual

6 Oktober 2024

Maxwell MX-25401 Manual

15 August 2024

Maxwell MX-25306 Manual

31 Juli 2024

Maxwell MX-25303 Manual

19 Februar 2024

Maxwell MX-25210 Manual

29 September 2023

Maxwell MX-25211 Manual

16 September 2023

Maxwell MX-25109 Manual

14 September 2023

Maxwell MX-25521 Manual

30 Juli 2023

Maxwell MX-25334 Manual

23 Juli 2023

Maxwell MX-25304 Manual

19 Juli 2023

Multimeter Manualer

Nyeste Multimeter Manualer

Fluke T+ Manual

1 August 2025

Trotec BE60 Manual

1 August 2025

Kyoritsu K2413F Manual

1 August 2025

Kyoritsu KEW 8601 Manual

1 August 2025

Kyoritsu KT 203 Manual

1 August 2025

Voltcraft PMM 6010-60 Manual

21 Juli 2025

Voltcraft VC351 Manual

20 Juli 2025

PeakTech 1072 Manual

16 Juli 2025

Yato YT-730895 Manual

16 Juli 2025

PeakTech 1071 Manual

14 Juli 2025