McIntosh C1100C Manual

McIntosh Modtager C1100C

Læs gratis den danske manual til McIntosh C1100C (6 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 18 anmeldelser. Har du et spørgsmål om McIntosh C1100C, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/6
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 www.mcintoshlabs.com
HR085 Learning Guide
2
Copyright 2015 © by McIntosh Laboratory, Inc.
Table of Contents
Technical Assistance
If at any time you have questions about your McIntosh
product, contact your McIntosh Dealer who is familiar
with your McIntosh equipment and any other brands
that may be part of your system. If you or your Dealer
wish additional help concerning a suspected problem,
you can receive technical assistance for all McIntosh
products at:
McIntosh Laboratory, Inc.
2 Chambers Street
Binghamton, New York 13903
Phone: 607-723-3512
Fax: 607-724-0549
Introduction ................................................................ 2
Remote Control Codes 2 ..............................................
Technical Assistance 2 ..................................................
Table of Contents 2 .......................................................
Preliminary Step ........................................................ 3
Signal Strength Test 3 ..................................................
Learning Commands .................................................. 3
Delete Learned Commands 4 ........................................
Reset the HR085 to Default Settings 4 ..........................
HR085 HEX Code Table ..........................................4-5
Introduction
The HR085 Remote Control is supplied with McIntosh
Preamplifiers, Integrated Amplifiers and Tuners.
The HR085 Remote Control has the ability to learn
and store Remote Control (RC) Commands from
three non-McIntosh Components. The RC Commands
stored in the HR085 can be accessed by using the
“DEVICE” Push-button together with the LED Indica-
tors to select one of the three (TV, CABLE or AUX).
Refer to figure 1 and the instructions starting on page
3 on “How to Learn and Store Commands”.
DEVICE
Push-button
LED
indicators
Remote Control Codes
The HR085 Remote Control has been factory con-
figured for the “Normal” McIntosh Control Codes
used with most models. There is a set of “Alternate”
McIntosh Control Codes for the HR085 Remote Con-
trol. “This Alternate Control Code” is to be used when
there are two McIntosh Models (A/V Control Center,
Integrated Amplifier or Preamplifier) in the same
location at the same time. This will prevent the HR085
Remote Control from adversely affecting the opera-
tion of the units. Refer to figure 1 when performing
the steps below.
Note: Refer to the “Setup” Section of the Owner’s
Manual supplied with the A/V Control Center,
Integrated Amplifier and/or Preamplifier for ad-
ditional information about using the “Alternate
Control Codes”.
To change the HR085 from “Normal” to “Alternate”
Control Codes perform the following steps:
1. To change from the “Normal” to “Alternate”
Control Codes, press and hold the SELECT and
number 2 Push-buttons simultaneously (for about
8 seconds) until the Device Select LED
flashes twice.
2. Referring to the SETUP Steps outlined in the
McIntosh Model Owner’s Manual, change one of
the two Models over to the “Alternate” Codes.
3. Press the VOLume ▲Up/ ▼Down Push-button
on the Remote Control to verify proper operation
using the Alternate Codes.
To change the HR085 from “Alternate” to “Normal”
Control Codes perform the following steps:
1. To change from the “Alternate” to “Normal”
Control Codes, press hold the SELECT and
number 1 Push-buttons simultaneously (for about
8 seconds) until the Device Select LED
flashes once.
Figure 1
Number 1
Push-button
Number 2
Push-button
SELECT
Push-button
2. Refering to the SETUP Steps outlined in the Mc-
Intosh Model Owner’s Manual change one of the
two Model over to the “Normal” Codes.
3. Press the VOLume ▲Up/ ▼Down Push-button
on the Remote Control to verify proper operation
using the Normal Codes.

Produkt Specifikationer

Mærke: McIntosh
Kategori: Modtager
Model: C1100C

Har du brug for hjælp?

Hvis du har brug for hjælp til McIntosh C1100C stil et spørgsmål nedenfor, og andre brugere vil svare dig


Modtager McIntosh Manualer

McIntosh

McIntosh MSA5500 Manual

17 Juli 2025
McIntosh

McIntosh MC3500 MKII Manual

5 Juli 2025
McIntosh

McIntosh C22 MK V Manual

5 Juli 2025
McIntosh

McIntosh MC-225 Manual

1 Oktober 2024
McIntosh

McIntosh C1100C Manual

20 September 2024
McIntosh

McIntosh MC-75 60th Anniversary Edition Manual

8 September 2024
McIntosh

McIntosh C2800 Manual

1 September 2024
McIntosh

McIntosh C55 Manual

1 September 2024
McIntosh

McIntosh C53 Manual

1 September 2024
McIntosh

McIntosh MA7200 Manual

30 August 2024

Modtager Manualer

Nyeste Modtager Manualer

AMX

AMX NMX-ENC-N2612S Manual

14 September 2025
AMX

AMX UDM-RX02N Manual

14 September 2025
AMX

AMX AVB-RX-DXLINK-HDMI Manual

14 September 2025
Perreaux

Perreaux Silhouette SXH2 Manual

13 September 2025
Perreaux

Perreaux Silhouette SXP2 Manual

13 September 2025
Perreaux

Perreaux Silhouette SX25i Manual

12 September 2025
Perreaux

Perreaux Silhouette SXV2 Manual

12 September 2025
Sony

Sony STR-DE635 Manual

12 September 2025
Perreaux

Perreaux Silhouette SX25 Manual

12 September 2025
Perreaux

Perreaux Audiant 80i Manual

12 September 2025