Mikrotik OmniTIK 5 PoE ac Manual

Mikrotik Adgangspunkt OmniTIK 5 PoE ac

Læs gratis den danske manual til Mikrotik OmniTIK 5 PoE ac (4 sider) i kategorien Adgangspunkt. Denne vejledning er vurderet som hjælpsom af 50 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 25.5 anmeldelser. Har du et spørgsmål om Mikrotik OmniTIK 5 PoE ac, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

OmniTik series

Quick setup guide and warranty information

The OmniTik is an outdoor wireless system with a built in antenna. It can be used as a wireless Access Point, CPE

or for point-to-point links. It supports wireless operation in the 5GHz range (specific frequencies depend on region).

Mounting

Slide the included pole mount adapter with the clip facing forward, until the clip clicks into place. Use the included

hose clamp to attach the unit to a pole or mast. Adjustable QuickMount adapters are available separately. The

OmniTik has a locking screw that secures the port door, it can be closed with a 5mm hex screwdriver.

Connecting

1. Open the Ethernet port door to connect your PC or LAN cables to the Ethernet ports, connect the other end

of the Ethernet cable to a PoE injector

2. Set LAN computer IP configuration to automatic (DHCP)

3. Default IP address of the unit is 192.168.88.1, open this address in your web browser to start configuration.

The username is and there is admin no password

Powering

The device accepts power from passive and active (802.3af/at) power sources. A passive PoE injector is included

in the box.

Power output

Applies only to OmniTik 5 PoE ac: This device can supply PoE power to external devices from its Ethernet ports.

This is convenient as you don't need any additional PoE injectors to power other devices. The output voltage will be

the same as input voltage. Maximum power output of each Ethernet port in this mode is 1A (total maximum for all

ports is 2A). To reach maximum output power it is recommended to use a high voltage adapter together with the

included PoE injector to power the OmniTik unit (48/56V), because 802.3af/at input is limited to 30W and OmniTik

will consume up to 15W by itself. Once Power Output is enabled in RouterOS, the Ethernet LED adds red color to

it (green means Ethernet link is made, red means power but no link, red and green both means there is link and

power).

Booting process

Initial connection has to be done via the Ethernet cable from the LAN side. Open 192.168.88.1 in your web

browser. Username is and there is . In case IP connection is not available, WinBox can be admin no password

used to connect to the MAC address of the device. More information here:

http://wiki.mikrotik.com/wiki/First_time_startup

In case you wish to boot the device from network, for example to use MikroTik Netinstall, hold the RESET button of

the device when starting it until the LED light turns off, and device will start to look for Netinstall servers.

Extension slots and ports

 Five 10/100/1000 Gigabit Ethernet ports, supporting automatic cross/straight cable correction (Auto

MDI/X), so you can use either straight or cross-over cables for connecting to other network devices.

 One integrated wireless 5GHz 802.11a/n/ac, 2x2 MIMO with built in grid antenna, max gain 7.5dBi

See www.routerboard.com for more information. Contact 6-May-16support@mikrotik.com

Buttons and jumpers

RouterBOOT reset button (RESET, front panel) has three functions:

• Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS

configuration (total 5 seconds)

• Keep holding for 5 more seconds, LED turns solid, release now to turn on CAPs mode

(total 10 seconds)

• Or Keep holding the button for 5 more seconds until until LED turns off, then release it to make the

RouterBOARD look for Netinstall servers (total 15 seconds)

Operating system support

Currently tested operating system is MikroTik RouterOS starting from version 6.30

reproduced or transmitted in any form without prior written permission from the copyright holder. RouterBOARD,

RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls SIA. All trademarks and registered trademarks

appearing in this document are the property of their respective holders.

Hardware. MikroTik warrants all RouterBOARD series equipment for the term of twelve (12) months from the

shipping date to be free of defects in materials and workmanship under normal use and service, except in case of

damage caused by mechanical, electrical or other accidental or intended damages caused by improper use or due

to wind, rain, fire or other acts of nature.

To return failed units to MikroTik, you must perform the following RMA (Return Merchandise Authorization)

procedure. Follow the instructions below to save time, efforts, avoid costs, and improve the speed of the RMA

process.

1. If you have purchased your product from a MikroTik Reseller, please contact the Reseller company

regarding all warranty and repair issues, the following instructions apply ONLY if you purchased your

equipment directly from MikroTik in Latvia.

2. MikroTik does not offer repairs for products that are not covered by warranty. Exceptions can be made for:

CCR1016-12G, CCR1016-12G-BU, CCR1036-12G-4S, RB1100, RB1100AH, RB1100AHx2, RB1200,

RB600, RB600A and RB800 as a paid service (fees apply).

3. Out-of-warranty devices and devices not covered by warranty sent to Mikrotik will be returned to the sender

at sender's cost. If the customer has not organized return of such rejected devices within 12 months from

the day of arrival, MikroTik has the right to discard them.

RMA Instructions are located on our webpage here: http://rma.mikrotik.com

This document is provided “as is” without a warranty of any kind, expressed or implied, including, but not limited to,

the implied warranty of merchantability and fitness for a particular purpose. The manufacturer has made every

effort to ensure the accuracy of the contents of this document, however, it is possible that it may contain technical

inaccuracies, typographical or other errors. No liability is assumed for any inaccuracy found in this publication, nor

for direct or indirect, incidental, consequential or other damages that may result from such an inaccuracy, including,

but not limited to, loss of data or profits. Please report any inaccuracies found to support@mikrotik.com

See www.routerboard.com for more information. Contact 6-May-16support@mikrotik.com

Produkt Specifikationer

Mærke:	Mikrotik
Kategori:	Adgangspunkt
Model:	OmniTIK 5 PoE ac
Vekselstrømsindgangsspænding:	12 - 57 V
Bredde:	129 mm
Dybde:	58 mm
Højde:	416 mm
Ethernet LAN-porte (RJ-45):	5
Antal USB 2.0-porte:	1
Ethernet LAN-datahastigheder:	10,100,1000 Mbit/s
Intern hukommelse:	128 MB
Kabler inkluderet:	Vekselstrøm
Strømforbrug (maks.):	18 W
Placering:	Pæl
Netværksstandarder:	IEEE 802.11ac,IEEE 802.3af,IEEE 802.3at
DC-in-stik:	Ja
AC-adapter inkluderet:	Ja
Harmoniseret systemkode (HS):	85176990
Intern:	Ingen
Maksimal dataoverførselshastighed:	54 Mbit/s
USB-stik type:	USB Type-A
Flashhukommelse:	16 MB
Strøm over Ethernet (PoE):	Ja
Monteringssæt:	Ja
Indbygget processer:	Ja
5 GHz:	Ja
Niveau for antennestyrke (maks.):	7.5 dBi
PoE-adapter inkluderet:	Ja