NUVO Livingston 60/7669 Manual

NUVO Lettelse Livingston 60/7669

Læs gratis den danske manual til NUVO Livingston 60/7669 (2 sider) i kategorien Lettelse. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om NUVO Livingston 60/7669, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

FOR YOUR SAFETY

WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE

WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR

THE CIRCUIT BREAKER IS SHUT OFF.

GENERAL

You don’t need special tools to install this xture. Be sure to follow

the steps in the order given. Under no circumstances should a xture

be hung on house electrical wires, nor should a swag type xture be

installed on a ceiling which contains a radiant type heating system.

Read instructions carefully. If you are unclear as to how to proceed,

consult a qualied electrician.

NOTE: Proper wiring is essential for the safe operation of this xture.

FIXTURE ASSEMBLY

Carefully remove the xture from the carton and check that all parts

are included as shown in gure. Be careful not to misplace any of the

screws or parts, which are needed to install this xture.

STEP 1: Fix the shade to the arms by using nuts.

STEP 2: Thread tube. Carefully pass the wires through each tube

during assembly. Repeat this step until the desired hanging height

is reached.

STEP 3: Thread the tube into canopy and body.

INSTALLATION

IMPORTANT: Do not attach xture directly to outlet box.

STEP 1: Thread mounting screw into the match hole of cross bar.

STEP 2: Secure the cross bar to outlet box with outlet box screws.

GROUNDING INSTRUCTIONS

STEP 1: Insert the green grounding screw into the hole with two raised

dimples on the mounting bar. Wrap the ground wire from the xture (if

supplied) around the green grounding screw, then connect it to ground

wire from the outlet box (if not xed on the outlet box) using a wire

connector (not supplied). If ground wire from the xture is not supplied,

wrap the ground wire (if not xed on the outlet box) from the outlet box

around the green grounding screw and tighten it.

NEVER CONNECT GROUND WIRE TO BLACK OR WHITE

POWER SUPPLY WIRES.

STEP 2: Take note of the color of the wire(s) on your xture. Identify

which group your xture wire(s) falls into and connect the wires

according to the directions below:

GROUP A:

Connect to Black House Wire

GROUP B:

Connect to White House Wire

BLACK WHITE

* PARALLEL WIRE (round & smooth) * PARALLEL WIRE (square & ridged)

WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER

BROWN, GOLD OR BLACK

WITHOUT TRACER

BROWN, GOLD OR BLACK

WITH TRACER

NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is

square shaped or ridged and the less tracer wire is round in shape or

smooth (seen best when viewed from wire end.)

STEP 3: Take your xture wire(s) from group A and place evenly against

the black wire from the outlet box. Do NOT twist wires together before

using wire connectors.

STEP 4: Fit a wire connector over the wires and screw the connector

clockwise until you feel rmness.

STEP 5: Try gently to pull the connector off the wires. If you can pull the

connector off, carefully re-do steps 3 and 4 as above, and check again

for a rm connection.

STEP 6: Connect the xture wire from group B to the white wire from

the outlet box in the same manner. Make sure no bare wires can be

seen outside wire connectors.

FINAL ASSEMBLY

STEP 1: After wires are connected, tuck them carefully inside outlet

box. Raise canopy allowing the mounting screw to protrude through the

hole in the canopy, and secure with ball nuts.

STEP 2: Install lamps (not included). Please do not exceed the maximum

capacity recommended on the socket.

CLEANING

To clean, wipe xture with a soft cloth. Clean glass with a mild soap.

Do not use abrasive materials such as scouring pads or powders, steel

wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to order

replacement parts. Be sure to use exact wording from illustration when

ordering parts.

FIGURE

Line art shown may not exactly match the xture enclosed. However, the installations

do apply to this xture.

La ilustración puede no concordar exactamente con la pieza enviada. Sin embargo,

las instalaciones sí aplican para esta pieza.

Les images peuvent ne pas correspondre exactement au luminaire de la boîte.

Par contre, les directives d’installation s’appliquent au luminaire.

INSTALLATION AND SAFETY INSTRUCTIONS

ITEM NO: 60-7668, 60-7669

ARTÍCULO Nº: 60-7668, 60-7669

ARTICLE N°: 60-7668, 60-7669

Lamp

Shade

Nut

Ball Nut

Produkt Specifikationer

Mærke:	NUVO
Kategori:	Lettelse
Model:	Livingston 60/7669

Har du brug for hjælp?

Hvis du har brug for hjælp til NUVO Livingston 60/7669 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lettelse NUVO Manualer

NUVO Ballerina 60/1265 Manual

4 April 2025

NUVO SF77/196 Manual

4 April 2025

NUVO Ballerina 60/329 Manual

4 April 2025

NUVO Cordello 60/7883 Manual

4 April 2025

NUVO Destin 60/7706 Manual

4 April 2025

NUVO Livingston 60/7669 Manual

4 April 2025

NUVO Terrace 60/7747 Manual

4 April 2025

NUVO 65/220 Manual

4 April 2025

NUVO Halter 60/7692 Manual

4 April 2025

NUVO Everton 60/7877 Manual

4 April 2025

Lettelse Manualer

Nyeste Lettelse Manualer

Schwaiger CALE100 511 Manual

9 April 2025

ADB Orkis Fresnel Manual

8 April 2025

Claypaky Actoris ParLED Manual

8 April 2025

ET2 Waterfall E24846-90 Manual

8 April 2025

Dainolite V166-1W Manual

5 April 2025

Dainolite OFE-161P Manual

5 April 2025

Dainolite DMLED10-A-5D Manual

5 April 2025

Dainolite DM1958F Manual

5 April 2025

Maxim Westlake 65102BK Manual

4 April 2025

Maxim Diverse 57641WTWT Manual

4 April 2025