NUVO Terrace 60/7747 Manual

NUVO Lettelse Terrace 60/7747

Læs gratis den danske manual til NUVO Terrace 60/7747 (2 sider) i kategorien Lettelse. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om NUVO Terrace 60/7747, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

FOR YOUR SAFETY

WARNING: BE SURE THE ELECTRICITY TO THE WIRES

YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS

REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.

GENERAL

You don’t need special tools to install this xture. Be sure to follow

the steps in the order given. Under no circumstances should

a xture be hung on house electrical wires, nor should a swag

type xture be installed on a ceiling which contains a radiant type

heating system. Read instructions carefully. If you are unclear as to

how to proceed, consult a qualied electrician.

NOTE: Proper wiring is essential for the safe operation of this

xture.

FIXTURE ASSEMBLY

Carefully remove the xture from the carton and check that all

parts are included as shown in gure. Be careful not to misplace

any of the screws or parts, which are needed to install this xture.

INSTALLATION

IMPORTANT: Do not attach xture directly to outlet box.

STEP 1: Fasten the cross bar onto the outlet box with the outlet

box screws.

STEP 2: Tie ground wire from outlet box and from xture to the

ground screw on the cross bar. Connect white wire from xture

to white wire (neutral wire) from supply circuit. Connect black

wire from xture to black wire (live wire) from supply circuit. Cover

connections using provided wire connectors.

GROUNDING INSTRUCTIONS

STEP 1: Insert the green grounding screw into the hole with two

raised dimples on the mounting bar. Wrap the ground wire from

the xture (if supplied) around the green grounding screw, then

connect it to ground wire from the outlet box (if not xed on the

outlet box) using a wire connector (not supplied). If ground wire

from the xture is not supplied, wrap the ground wire (if not xed

on the outlet box) from the outlet box around the green grounding

screw and tighten it.

NEVER CONNECT GROUND WIRE TO BLACK OR WHITE

POWER SUPPLY WIRES.

STEP 2: Take note of the color of the wire(s) on your xture.

Identify which group your xture wire(s) falls into and connect the

wires according to the directions below:

GROUP A:

Connect to Black House Wire

GROUP B:

Connect to White House Wire

BLACK WHITE

* PARALLEL WIRE (round & smooth) * PARALLEL WIRE (square & ridged)

WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER

BROWN, GOLD OR BLACK

WITHOUT TRACER

BROWN, GOLD OR BLACK

WITH TRACER

NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire

is square shaped or ridged and the less tracer wire is round in

shape or smooth (seen best when viewed from wire end.)

STEP 3: Take your xture wire(s) from group A and place evenly

against the black wire from the outlet box. Do NOT twist wires

together before using wire connectors.

STEP 4: Fit a wire connector over the wires and screw the

connector clockwise until you feel rmness.

STEP 5: Try gently to pull the connector off the wires. If you can

pull the connector off, carefully re-do steps 3 and 4 as above, and

check again for a rm connection.

STEP 6: Connect the xture wire from group B to the white wire

from the outlet box in the same manner. Make sure no bare wires

can be seen outside wire connectors.

FINAL ASSEMBLY

STEP 1: After wires are connected, tuck them carefully inside

outlet box. Place the xture body to the wall by aligning the

protruding mounting screws all the way through the wall plate and

tighten nial to the mounting screws until the xture body is held

rmly against the wall.

STEP 2: Secure the glass to the xture using the socket ring.

STEP 3: Install lamp (not included). Do not exceed the maximum

capacity recommended on the socket.

CLEANING

To clean, wipe xture with a soft cloth. Clean glass with a mild

soap. Do not use abrasive materials such as scouring pads or

powders, steel wool or abrasive paper.

ORDER ING PARTS

Keep this sheet for future reference, and in case you need to order

replacement parts. Be sure to use exact wording from illustration

when ordering parts.

FIGURE

Line art shown may not exactly match the xture enclosed. However, the installations

do apply to this xture.

La ilustración puede no concordar exactamente con la pieza enviada. Sin embargo,

las instalaciones sí aplican para esta pieza.

Les images peuvent ne pas correspondre exactement au luminaire de la boîte.

Par contre, les directives d’installation s’appliquent au luminaire.

INSTALLATION AND SAFETY INSTRUCTIONS

ITEM NO: 60-7747, 60-7748, 60-7749

ARTÍCULO Nº: 60-7747, 60-7748, 60-7749

ARTICLE N°: 60-7747, 60-7748, 60-7749

Produkt Specifikationer

Mærke:	NUVO
Kategori:	Lettelse
Model:	Terrace 60/7747

Har du brug for hjælp?

Hvis du har brug for hjælp til NUVO Terrace 60/7747 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lettelse NUVO Manualer

NUVO Ballerina 60/1265 Manual

4 April 2025

NUVO SF77/196 Manual

4 April 2025

NUVO Ballerina 60/329 Manual

4 April 2025

NUVO Cordello 60/7883 Manual

4 April 2025

NUVO Destin 60/7706 Manual

4 April 2025

NUVO Livingston 60/7669 Manual

4 April 2025

NUVO Terrace 60/7747 Manual

4 April 2025

NUVO 65/220 Manual

4 April 2025

NUVO Halter 60/7692 Manual

4 April 2025

NUVO Everton 60/7877 Manual

4 April 2025

Lettelse Manualer

Nyeste Lettelse Manualer

Schwaiger CALE100 511 Manual

9 April 2025

ADB Orkis Fresnel Manual

8 April 2025

Claypaky Actoris ParLED Manual

8 April 2025

ET2 Waterfall E24846-90 Manual

8 April 2025

Dainolite V166-1W Manual

5 April 2025

Dainolite OFE-161P Manual

5 April 2025

Dainolite DMLED10-A-5D Manual

5 April 2025

Dainolite DM1958F Manual

5 April 2025

Maxim Westlake 65102BK Manual

4 April 2025

Maxim Diverse 57641WTWT Manual

4 April 2025