Panduit CT-1701 Manual

Panduit Ikke kategoriseret CT-1701

Læs gratis den danske manual til Panduit CT-1701 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Panduit CT-1701, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Part No. CT-1701

OPERATION INSTRUCTIONS

Contour Crimp

CONTROLLED CYCLE

CRIMPING TOOL

Crimps Panduit #10 - #2 AWG

non-insulated P series terminals and

#14 - 10 AWG copper

code conductor lugs.

Includes 5-position, rotating die.

Provides UL Listed and CSA Certified terminations

with applicable Panduit terminals.

COPPER COMPRESSION CONNECTOR

CRIMPING INSTRUCTIONS

1. With the handles in the position,open

depress die release and rotate die to desired

pocket. The pocket will lock in place when

an audible “click” is heard (Die index number

appears to the left of corresponding pocket).

CAUTION: Do not cycle tool unless the

die release button has seated and the die

has locked in place.

Refer to product packaging for selection of

the proper crimp pocket. Place the desired

compression connector in the crimp pocket

(See Fig. 2).

2. Close handles until the connector is held

snugly in position—do not deform the

barrel.

3. Insert the stripped wire into the connector

until the wire stops. Refer to product

packaging for wire strip length.

4. Crimp the connector by closing the handles

until the controlled cycle mechanism

releases. Repeat this operation for the

compression connectors that require more

than one compression. Upon release, the

handles will open automatically and the

crimped connector can be removed.

After crimping, inspect that the crimp is

centered on the barrel in order to achieve

optimal pullout performance.

OPERATION INSTRUCTIONS

PA23829A01

Rev.: 05 3-2017

CT-1701

Figure 1

CRIMP POCKETS FOR Panduit

Compression Connectors.

Refer to product packaging for

wire range and proper crimp

pocket. Crimp pockets are

identified with applicable die

index number.

Cushioned Handle Grips

Manual release lever, push

forward in the event that

controlled cycle mechanism

must be released.

Controlled cycle mechanism

prevents tool from opening

before crimp cycle is complete.

Email:

techsupport@panduit.com

EU Website: www.panduit.com/emea

EU Email: emeatoolservicecenter@panduit.com

Technical Support:

Tel: 1-800-777-3300

Panduit Europe • EMEA Service Center

Tel: +31 546 580 452 • Fax: +31 546 580 441

CAUTION: Verify power is “OFF” before

working on wiring with this tool. The

cushioned grips are for the user’s com-

fort, and are not intended to insulate

against shock while working on live

electrical circuits.

Page: 1 of 2

Rotating Crimp Die Wheel

Crimp Die Release Push Button

Figure 2

www.panduit.com

INSPECTION / MAINTENANCE

VISUAL INSPECTION

1. Visually inspect the tool for missing or loose

pins, then close the tool and note the return

action of the handles.

2. Inspect the crimping dies for worn, chipped

or broken edges.

3. If parts are missing, defective or damaged,

contact Panduit Customer Service or

Panduit EMEA Service Center for

information on repair or replacement of tools.

DIE CLOSURE INSPECTION

Die closure is measured by using GO/NO GO

gage members (dimensions listed in Table 1).

1. Clean the crimping dies and gage member surfaces.

2. Close the tool handles until the crimping dies are bottomed and the controlled cycle mechanism

releases. Keep the handles closed together.

3. Using the appropriate gage member, attempt to insert the NO GO gage into the die opening. The NO

GO side may partially enter the die closure but must NOT pass completely through. Perform this test

for all three crimp pockets.

4. Repeat Step 3 with the appropriate GO gage for all three crimp pockets. The GO side must enter

and pass completely through the die closures.

5. If both gage conditions are met, the tool is dimensionally correct. If either condition fails, contact

Panduit Customer Service, or Panduit EMEA Service Center for technical assistance.

PRELOAD FORCE INSPECTION

1. Close the handles until the controlled cycle

mechanism is engaged, but before the

mechanism releases.

2. Apply a force to the handles 1-1/4" (32 mm)

from the end of the handles, until the

controlled cycle release mechanism

releases. Record the reading using a force

gauge.

3. The force required to release the controlled

cycle release mechanism should be a

minimum of 15 pounds-force (67 N). If the

force required is less than 15 pounds-force

(67 N), contact Panduit Customer Service, or

Panduit EMEA Service Center for technical

assistance.

Table 1

NEW TOOLS -

BEFORE PLACING INTO SERVICE:

All Panduit crimping tools are calibrated and inspected before they are

shipped from the factory. All new tools should be inspected before being

used.

New tools are shipped, factory lubricated, in protective packaging. After

inspection, simply clean any excess oil from the crimping dies and place into

service.

When the tool is not in use, keep the handles closed to prevent objects from

becoming lodged in the crimping area. Store the tool in a clean, dry area.

IN-SERVICE TOOLS -

AFTER TOOLS HAVE BEEN IN SERVICE:

It is recommended that each operator of the tool be made aware of-and

responsible for following these maintenance steps.:

In-service tools should be cleaned and inspected at least ONCE A MONTH.

To clean-wipe with a clean cloth.

In-service tools should be lubricated ONCE A WEEK, and after every

cleaning. Lubricate all pins, pivots and bearing surfaces with DOW

CORNING®Molykote BR2 Plus. Do not use oil excessively.

Be sure to clean any excess oil from the crimping dies before using.

® Molykote BR2 Plus is the Registered Trademark

of DOW CORNING

DIE CLOSURE GO / NO GO GAGE MEMBERS - TOOL NO. CT-1701

DIE INDEX

NUMBER

ENGLISH GO / NO GO GAGE MEMBERS METRIC GO / NO GO GAGE MEMBERS

“G” Dia. (GO) “NG” Dia. (NO GO) “G” Dia. (GO) “NG” Dia. (NO GO)

P10 0.099” 0.109” 2,51 mm 2,76 mm

P8 0.179” 0.201” 4,54 mm 5,10 mm

P6 0.217” 0.238” 5,51 mm 6,04 mm

P4 0.273” 0.295” 6,93 mm 7,49 mm

P2 0.351” 0.374” 8,91 mm 9,49 mm

Page: 2 of 2

TROUBLESHOOTING

OPERATION INSTRUCTIONS CT-1701

Produkt Specifikationer

Mærke:	Panduit
Kategori:	Ikke kategoriseret
Model:	CT-1701

Har du brug for hjælp?

Hvis du har brug for hjælp til Panduit CT-1701 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Panduit Manualer

Panduit MIW094 Manual

2 September 2025

Panduit MIW125 Manual

2 September 2025

Panduit PES400 Manual

2 September 2025

Panduit CUCGF06DPW1 Manual

2 September 2025

Panduit CUEFRCKITW1 Manual

2 September 2025

Panduit MIM125 Manual

2 September 2025

Panduit CUSREORCPB1 Manual

2 September 2025

Panduit VS2-AVT-3IB Manual

27 August 2025

Panduit VS-AVT-C08-L10 Manual

27 August 2025

Panduit GPQC07-1/0 Manual

27 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kimo LR 110 Manual

2 September 2025

HMS Premium LPD02 Manual

2 September 2025

AVer E1008 Manual

2 September 2025

Biltema 17-547 Manual

2 September 2025

Groen AH/1E Manual

2 September 2025

ACOPower HY-P30 Manual

2 September 2025

Yamaha True X Speaker 3A WS-X3A Manual

2 September 2025

Globe RG30 Manual

2 September 2025

Deye SUN-6K-SG05LP1-EU-AM2-P Manual

2 September 2025

Neutrik NLT4FXX Manual

2 September 2025