Panduit CT-200 Manual

Panduit Ikke kategoriseret CT-200

Læs gratis den danske manual til Panduit CT-200 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Panduit CT-200, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

CT-200

CRIMPING TOOL

OPERATION INSTRUCTIONS

Page: 1 of 1

PA24428A01

REV.: 02 6-2018

OPERATION INSTRUCTIONS

CT-200

Technical Support:

1-800-777-3300

E-mail:

techsupport@panduit.com

WIRE CUTTER for No. 10 AWG and

smaller copper wire.

CRIMP POCKET for Pan-Term non-

insulated terminals, disconnects,

splices and wire joints.

The 12-10 pocket is for No. 12 to No. 10

solid or stranded wire; the 22-14 pocket

is for No. 22 to No. 14 solid or stranded

wire. The crimp should be centrally

located on the barrel with the indenter

on the seam, and the dies fully closed

for best results.

This tool is made of hardened steel and

is protected with a light coat of oil.

See product packaging or contact Customer Service for

UL/CSA approved tooling/product combination.

NON-INSULATED WIRE JOINT

INSTRUCTIONS

1. Twist ends of stripped wire together,

trim and insert into wire joint. (See

product packaging for proper strip

lengths and trimming instructions.)

2. Locate wire joint in proper non-insulated

crimp pocket.

3. Position crimp pocket on the center of

the metal barrel.

4. Squeeze handles firmly.

CRIMP POCKET

NON-INSULATED BUTT SPLICE

INSTRUCTIONS

1. Insert stripped wire into end of the butt

splice to internal wire stop. (See product

packaging for proper strip lengths.)

2. Locate butt splice in proper non-

insulated crimp pocket.

3. Position crimp pocket on the center of

the metal barrel half with wire inserted.

4. Squeeze handles firmly.

5. Repeat for other end of butt splice.

CRIMP POCKET

NON-INSULATED

TERMINAL AND DISCONNECT

INSTRUCTIONS

1. Insert stripped wire into terminal or

disconnect until a minimum of 1/32" of

conductor extends beyond barrel. (See

product packaging for proper strip

lengths.)

2. Locate terminal or disconnect in proper

non-insulated crimp pocket.

3. Position crimp pocket on the center of the

metal barrel.

4. Squeeze handles firmly.

CRIMP POCKET

CAUTION:

Verify power is “OFF” before working on wiring with this tool.

The plastic grips are for the user’s comfort,

and are not intended to insulate against electrical shock

while working on live electrical circuits.

www.panduit.com

Produkt Specifikationer

Mærke:	Panduit
Kategori:	Ikke kategoriseret
Model:	CT-200

Har du brug for hjælp?

Hvis du har brug for hjælp til Panduit CT-200 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Panduit Manualer

Panduit VS2-NET Manual

29 November 2025

Panduit PWBCB12 Manual

18 November 2025

Panduit NCMHF1 Manual

31 Oktober 2025

Panduit CEG-13X1 Manual

9 Oktober 2025

Panduit PR2HF1 Manual

9 Oktober 2025

Panduit C2FAB07A1200B1 Manual

8 Oktober 2025

Panduit CEST1-D3 Manual

8 Oktober 2025

Panduit CBEWHY Manual

8 Oktober 2025

Panduit CEG-05X2 Manual

8 Oktober 2025

Panduit CEST2-A6 Manual

8 Oktober 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

BEKO DVS15022W Manual

7 December 2025

Opticis OPS-xyz Manual

7 December 2025

Opticis BR-500 Manual

7 December 2025

Opticis DPOC-14N Manual

7 December 2025

Zotac GAMING GeForce RTX 5060 Twin Edge Manual

7 December 2025

FiiO BR15 R2R Manual

7 December 2025

Fostex FE83NV2 Manual

7 December 2025

Fostex EN15 Manual

7 December 2025

Advantech iDAQ-731D Manual

7 December 2025

Bosch MAF462C0 Manual

7 December 2025