Panduit NKSPMIW Manual


Læs gratis den danske manual til Panduit NKSPMIW (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 47 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 24 anmeldelser. Har du et spørgsmål om Panduit NKSPMIW, eller vil du spørge andre brugere om produktet?

Side 1/2
INSTALLATION INSTRUCTIONS NK194B
© Panduit Corp. 2007
For Technical Support: www.panduit.com/resources/install_maintain.asp
N KET EY
NETWORK COMPONENTS
CONTRACTOR GRADE
Page 1 of 2
TERMINATION INSTRUCTIONS
Signal Ground
RCA Module
S-Video Module
Chrominance
Chrominance Ground
Luminance Ground
Luminance
Remove approximately 1" of cable jacket. (CAUTION: Do not damage conductors.) Fan out twisted pairs for
termination.
S-Video Module RCA Module
STEP 1
Use the PDT110 Single Wire Punchdown tool to punchdown conductors in the orientation shown.
Modules should appear as shown below when terminated.
Signal
STEP 2
Signal and Signal Ground use one twisted pair
Chrominance and Chrominance Ground use one twisted pair
Luminance and Luminance Ground use one twisted pair
N KET EY RCA and S-Video
110 Style Punchdown Modules
Part Numbers: NKSPM**, NKRPM***, NKSPB
(UTP Cable)
White / Blue
Blue
White / Orange
Orange
E-mail:
cs@panduit.com
Fax:
866-449-1702
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp www.panduit.com
INSTALLATION INSTRUCTIONS NK194B
Page 2 of 2
Use the optional NKSPB N KET EY 110PD Module Puck to align and hold the module for
termination to the connector block.
Set fully assembled Module into puck, aligning Flexible snap on module with screwdriver
slot on puck. Snap in place. Do not press on the connector to snap in place.
To remove module from puck, place index finger on the opposite side of the screwdriver
slot and thumb on the NETKEY housing, not on the punch-down block, otherwise module
will be damaged. Apply pressure to Module Flexible snap, tilt module, and remove. Using
a small screwdriver to remove the module is optional.
Screwdriver is optional
to remove N KET EY
Module from puck.
OPTIONAL STEP
Install the P110RC2 wire retention cap onto the connector block.
Modules should appear as shown below when completed.
STEP 3
S-Video Module RCA Module
INSTALLATION TIPS:
1. PAN-PUNCH product terminates most 22-26 AWG solid or stranded IWC wire with a .050" (1.27mm) max. o.d., either PVC or Plenum rated.
2. Never install wire into a slot previously used for a larger gauge.
3. Be careful to strip back cable jacket only as required for termination.
4. Use care to maintain pair twists to within 0.5 inches (13mm) of the termination strip.
5. When stripping cable jacket, be careful not to cut the insulation on the individual wires.
6. Avoid sharp bends when routing cable.
NKSPB
Flexible
Screwdriver
Snap
Slot
Screwdriver
Slot
MODULE INSTALLATION
MODULE REMOVAL


Produkt Specifikationer

Mærke: Panduit
Kategori: Ikke kategoriseret
Model: NKSPMIW

Har du brug for hjælp?

Hvis du har brug for hjælp til Panduit NKSPMIW stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Panduit Manualer

Panduit

Panduit MEHT187 Manual

29 December 2024
Panduit

Panduit DIRBB2007S21W Manual

29 December 2024
Panduit

Panduit CDE3 Manual

29 December 2024
Panduit

Panduit EC001 Manual

29 December 2024
Panduit

Panduit PZICE Manual

15 December 2024
Panduit

Panduit PZICEA Manual

15 December 2024
Panduit

Panduit PZNDVK Manual

15 December 2024
Panduit

Panduit DIRLC9606RB1 Manual

11 December 2024
Panduit

Panduit EA001 Manual

9 December 2024
Panduit

Panduit FPONE2 Manual

14 November 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer