Panduit TGJT Manual

Panduit Ikke kategoriseret TGJT

Læs gratis den danske manual til Panduit TGJT (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Panduit TGJT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

FIGURE 1:

1. Operator should manually

wire the required TG style

Jack Wire Cap for the desired

application. Wires must be

separated and slightly down

over the individual pocket

divider wedges. Depress

strain relief collar to secure

cable.

MADE IN COSTA RICA

TGJT PA25217A01

Rev. 03 2-2016

OPERATING INSTRUCTIONS

Page: 1 of 2

FIGURE 2:

2. Insert the prepared Wire Cap

into the Wire Seating/Cutting

side of the TGJT Tool. This

side pocket properly aligns

and holds the prepared Wire

Cap in place. Make sure all

twisted pairs of wires are out

to the sides of the Wire Cap

for proper cutting (refer to

Figure 1). The ramp of the

Wire Cap must be pointing

upward and be inserted

into the groove in the upper

Cutter Blade Anvil.

FIGURE 3:

3. Pull the handle and the mechanism seats the conductors into

the Wire Cap. At the same time, the Cutter Blades trim the

wires nearly flush with the side faces of the Wire Cap.

4. Keeping the handles closed, slide the Wire Cap up and out of

the tool. All wires should cut cleanly.

www.panduit.com

Technical Support: Panduit USA

888-506-5400, Ext. 86914

E-mail: techsupport@panduit.com

NOTE: STRIPPED WIRES MUST BE LONG ENOUGH TO

STICK OUT OF THE SIDES OF THE WIRE CAP.

Refer to product installation instructions listed above

for recommended wire strip lengths.

RAMP

ANVIL GROOVE

NOTE: IF THE WIRES DO NOT CUT CLEANLY OR THE WIRE

CAP DOES NOT WANT TO COME OUT, EXAMINE THE

CUTTER BLADE EDGE SURFACES AT THE NEXT

OPENING CYCLE. IF BLADES ARE NICKED OR

APPEAR WORN, REPLACE THEM WITH THE BLADE

REPLACEMENT KIT.

TGJT TOOL

DIVIDER

WEDGES

Refer to product installation instructions for

TX6 PLUS and TX5e UTP Jack Modules: PN403M

and TX6A 10Gig UTP Jack Modules: PN511E

for wiring instructions.

STRAIN

RELIEF

COLLAR

TG STYLE JACK TERMINATION TOOL

FOR INSTALLING ALL

TG STYLE COPPER JACK MODULES

Part No.: TGJT

Produkt Specifikationer

Mærke:	Panduit
Kategori:	Ikke kategoriseret
Model:	TGJT

Har du brug for hjælp?

Hvis du har brug for hjælp til Panduit TGJT stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Panduit Manualer

Panduit VS2-NET Manual

29 November 2025

Panduit PWBCB12 Manual

18 November 2025

Panduit NCMHF1 Manual

31 Oktober 2025

Panduit CEG-13X1 Manual

9 Oktober 2025

Panduit PR2HF1 Manual

9 Oktober 2025

Panduit C2FAB07A1200B1 Manual

8 Oktober 2025

Panduit CEST1-D3 Manual

8 Oktober 2025

Panduit CBEWHY Manual

8 Oktober 2025

Panduit CEG-05X2 Manual

8 Oktober 2025

Panduit CEST2-A6 Manual

8 Oktober 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

BEKO DVS15022W Manual

7 December 2025

Opticis OPS-xyz Manual

7 December 2025

Opticis BR-500 Manual

7 December 2025

Opticis DPOC-14N Manual

7 December 2025

Zotac GAMING GeForce RTX 5060 Twin Edge Manual

7 December 2025

FiiO BR15 R2R Manual

7 December 2025

Fostex FE83NV2 Manual

7 December 2025

Fostex EN15 Manual

7 December 2025

Advantech iDAQ-731D Manual

7 December 2025

Bosch MAF462C0 Manual

7 December 2025