Panduit WMPFSE-E Manual

Panduit Ikke kategoriseret WMPFSE-E

Læs gratis den danske manual til Panduit WMPFSE-E (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 49 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 25 anmeldelser. Har du et spørgsmål om Panduit WMPFSE-E, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

For Worldwide Subsidiaries

and Sales Offices visit

Web Site: www.panduit.com

INSTRUCTIONS CM282C

Technical Support Phone: 866-405-6654

Fax: 708-444-6993

E-mail: ncginfo@panduit.com

Page 1 of 1

Cable Capacity

Part Number UTP Cable

.187 dia.

SeTP Cable

.250 dia. Fiber

3mm dia.

Method 1

Method 2

WMP1E

WMPF1E

WMPFSE

WMPH2E

WMPHF2E

WMPLFSE

WMPLSE

WMPSE

96 72 312

72 48 192

48 32 144

24 16 72

Flange

The PatchLink cable manager is recommended for use with Panduit 24 or 48 port patch panels mounted above and below the manager.

When routing the cables for the patch panels, either of the following two methods are recommended to help maintain cable bend radius.

METHOD 1:For each row of 24 ports, place two cables in each slot on the manager.

Route half the cables through each of the wire retainers on the ends of the manager.

METHOD 2: If the cables are coming from one side of the rack, place 2 cables in each of the slots on the manager.

Wire

Retainer

Wire

Retainer

METHOD 1

METHOD 2

19” Rack

Screws

Finger

WMP1E (shown)

Cover

Part Numbers: WMP1E, WMPF1E,WMPFSE, WMPH2E, WMPHF2E, WMPLFSE,

WMPLSE, WMPSE

WMP1E

WMPF1E

WMPFSE

WMPH2E

WMPHF2E

WMPLFSE

WMPLSE

WMPSE

The hinged cover opens from the top or the

bottom. Pull flange to open and close cover.

P LATCH INK

Cable Management Horizontal Panels

Install the managers to the rack with the #12-24x.5 or M6 screws provided. Built-in

screw retention in mounting holes secures screws in manager during installation.

Install the covers to the manager by positioning cover flat against the front of the

manager fingers, then push to snap in place.

Note: The recommended assembly torque shall be 9+/-1 in-lb for #12-24 screws,

1+/-0.1 N-m for M6 screws.

NOTE: When using front and back WMPH’s to manage cables on the rear of the rack, place 2 cables in each of the 12 slots in the rear of

the manager, for each row of 24 ports.

Produkt Specifikationer

Mærke:	Panduit
Kategori:	Ikke kategoriseret
Model:	WMPFSE-E

Har du brug for hjælp?

Hvis du har brug for hjælp til Panduit WMPFSE-E stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Panduit Manualer

Panduit VS2-NET Manual

29 November 2025

Panduit PWBCB12 Manual

18 November 2025

Panduit NCMHF1 Manual

31 Oktober 2025

Panduit CEG-13X1 Manual

9 Oktober 2025

Panduit PR2HF1 Manual

9 Oktober 2025

Panduit C2FAB07A1200B1 Manual

8 Oktober 2025

Panduit CEST1-D3 Manual

8 Oktober 2025

Panduit CBEWHY Manual

8 Oktober 2025

Panduit CEG-05X2 Manual

8 Oktober 2025

Panduit CEST2-A6 Manual

8 Oktober 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

BEKO DVS15022W Manual

7 December 2025

Opticis OPS-xyz Manual

7 December 2025

Opticis BR-500 Manual

7 December 2025

Opticis DPOC-14N Manual

7 December 2025

Zotac GAMING GeForce RTX 5060 Twin Edge Manual

7 December 2025

FiiO BR15 R2R Manual

7 December 2025

Fostex FE83NV2 Manual

7 December 2025

Fostex EN15 Manual

7 December 2025

Advantech iDAQ-731D Manual

7 December 2025

Bosch MAF462C0 Manual

7 December 2025