Panduit WMPLFSE Manual

Panduit Ikke kategoriseret WMPLFSE

Læs gratis den danske manual til Panduit WMPLFSE (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Panduit WMPLFSE, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

For Worldwide Subsidiaries

and Sales Offices visit

Web Site: www.panduit.com

INSTRUCTIONS CM282C

Technical Support Phone: 866-405-6654

Fax: 708-444-6993

E-mail: ncginfo@panduit.com

Page 1 of 1

Cable Capacity

Part Number UTP Cable

.187 dia.

SeTP Cable

.250 dia. Fiber

3mm dia.

Method 1

Method 2

WMP1E

WMPF1E

WMPFSE

WMPH2E

WMPHF2E

WMPLFSE

WMPLSE

WMPSE

96 72 312

72 48 192

48 32 144

24 16 72

Flange

The PatchLink cable manager is recommended for use with Panduit 24 or 48 port patch panels mounted above and below the manager.

When routing the cables for the patch panels, either of the following two methods are recommended to help maintain cable bend radius.

METHOD 1:For each row of 24 ports, place two cables in each slot on the manager.

Route half the cables through each of the wire retainers on the ends of the manager.

METHOD 2: If the cables are coming from one side of the rack, place 2 cables in each of the slots on the manager.

Wire

Retainer

Wire

Retainer

METHOD 1

METHOD 2

19” Rack

Screws

Finger

WMP1E (shown)

Cover

Part Numbers: WMP1E, WMPF1E,WMPFSE, WMPH2E, WMPHF2E, WMPLFSE,

WMPLSE, WMPSE

WMP1E

WMPF1E

WMPFSE

WMPH2E

WMPHF2E

WMPLFSE

WMPLSE

WMPSE

The hinged cover opens from the top or the

bottom. Pull flange to open and close cover.

P LATCH INK

Cable Management Horizontal Panels

Install the managers to the rack with the #12-24x.5 or M6 screws provided. Built-in

screw retention in mounting holes secures screws in manager during installation.

Install the covers to the manager by positioning cover flat against the front of the

manager fingers, then push to snap in place.

Note: The recommended assembly torque shall be 9+/-1 in-lb for #12-24 screws,

1+/-0.1 N-m for M6 screws.

NOTE: When using front and back WMPH’s to manage cables on the rear of the rack, place 2 cables in each of the 12 slots in the rear of

the manager, for each row of 24 ports.

Produkt Specifikationer

Mærke:	Panduit
Kategori:	Ikke kategoriseret
Model:	WMPLFSE

Har du brug for hjælp?

Hvis du har brug for hjælp til Panduit WMPLFSE stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Panduit Manualer

Panduit MIW094 Manual

2 September 2025

Panduit MIW125 Manual

2 September 2025

Panduit PES400 Manual

2 September 2025

Panduit CUCGF06DPW1 Manual

2 September 2025

Panduit CUEFRCKITW1 Manual

2 September 2025

Panduit MIM125 Manual

2 September 2025

Panduit CUSREORCPB1 Manual

2 September 2025

Panduit VS2-AVT-3IB Manual

27 August 2025

Panduit VS-AVT-C08-L10 Manual

27 August 2025

Panduit GPQC07-1/0 Manual

27 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kimo LR 110 Manual

2 September 2025

HMS Premium LPD02 Manual

2 September 2025

AVer E1008 Manual

2 September 2025

Biltema 17-547 Manual

2 September 2025

Groen AH/1E Manual

2 September 2025

ACOPower HY-P30 Manual

2 September 2025

Yamaha True X Speaker 3A WS-X3A Manual

2 September 2025

Globe RG30 Manual

2 September 2025

Deye SUN-6K-SG05LP1-EU-AM2-P Manual

2 September 2025

Neutrik NLT4FXX Manual

2 September 2025