Powerhouse LS7T-52 Manual
Powerhouse
Brændekløver
LS7T-52
Læs nedenfor 📖 manual på dansk for Powerhouse LS7T-52 (16 sider) i kategorien Brændekløver. Denne guide var nyttig for 12 personer og blev bedømt med 4.4 stjerner i gennemsnit af 6.5 brugere
Side 1/16
1
LS7T-52 LOG SPLITTER
Operation Manual
Please carefully read this operation manual before starting work.
2
IMPORTANT! READ BEFORE REMOVING LOG SPLITTER
Always use CAUTION when working with machinery.
CAUTION: Oil may leak during the assembly process. It is advised to lay down
cardboard or newspaper prior to assembly in case this happens.
1. Carefully the Main Body (part no. 45 in manual) and Motor Assembly remove
(part no. 41, packed in a separate polyfoam box) from the packaging box. Turn
over the main body and place it on the foam block, which is inside the packaging
box with the machine.
MAKE SURE THE WEDGE FACES TOWARDS THE GROUND (the log
splitter will be upside-down).
2. Remove the hexangular spanner (alan wrench) from the spare parts bag. Unscrew
the THREE (3) silvery inner hexangular bolts on the end of the main body.
Remove the YELLOW QUADRATE IRON PLATE (this piece will be re-not
attached).
Remove the two (2) O-ring oil seals the YELLOW QUADRATE IRON inside
PLATE.
Take the O-ring oil seals and insert them into the two (2) holes on top of the oil
pump cover (part no. 40) which is attached to the Motor Assembly (part no. 41).
(These two (2) wholes are the same size as the holes inside the yellow quadrate
iron plate). the O-ring oil seals on the pump cover in the same fashion they Install
were when they were on the yellow quadrate iron plate.
3. Connect the Motor Assembly (part no. 41) onto the main body (part no. 45).
These parts will be connected in the same manner they were prior to removing the
yellow quadrate plate.
Align the three (3) holes on top of the Oil Pump Cover (part no. 40) with the three
(3) holes on the Main Body. Tighten the holes with the three silvery inner
hexangular bolts. *Accurate alignment will ensure against spilling oil*
4. To complete assembly of WHEELS, SUPPORT FEET, AND OPERATING
HANDLE, see Operation Manual.
Produkt Specifikationer
| Mærke: | Powerhouse |
| Kategori: | Brændekløver |
| Model: | LS7T-52 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Powerhouse LS7T-52 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Brændekløver Powerhouse Manualer
30 August 2024
Brændekløver Manualer
- Brændekløver Wallenstein
- Brændekløver Gamma
- Brændekløver RYOBI
- Brændekløver Remington
- Brændekløver Güde
- Brændekløver Fieldmann
- Brændekløver Scheppach
- Brændekløver Einhell
- Brændekløver Baumr-AG
- Brændekløver Atika
- Brændekløver Sun Joe
- Brændekløver Zipper
- Brændekløver Meec Tools
- Brændekløver Cocraft
- Brændekløver Bell
Nyeste Brændekløver Manualer
1 Oktober 2024
30 September 2024
6 September 2024
6 September 2024
6 September 2024
4 September 2024
28 August 2024
28 August 2024
28 August 2024
28 August 2024