Princeton Tec Apex Pro Manual

Princeton Tec Lommelygte Apex Pro

Læs gratis den danske manual til Princeton Tec Apex Pro (2 sider) i kategorien Lommelygte. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Princeton Tec Apex Pro, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Battery Installation

See battery installation diagram

2 CR123

Observe proper battery polarity when installing

the batteries.

WARNING

• Never mix fresh and used batteries.

• Never mix different battery brands

• Always remove drained batteries immediately.

• Remove batteries during long periods of storage.

Princeton Tec cares about the environment and

recommends recycling batteries. For more

information about battery recycling, please go to:

www.batteryrecycling.com

Improper installation of the batteries will damage the

light and void the warranty.

The battery pack has a waterproof seal. It is important

to keep this seal free from dirt and harsh chemicals in

order to preserve waterproof integrity. Inspect the seal

every time batteries are changed. If dirt is present,

wipe gently with a damp cotton swab and mild soap

until dirt is removed.

FOR CALIFORNIA RESIDENTS

WARNING: This product contains Bisphenol A (BpA)

a chemical known to the State of California to cause

birth defects or other reproductive harm.

Battery Power Meter

Multicolored LED

*Capacity percentage is the minimum expected

remaining power needed to operate the Maxbright

LED in high mode at 0° C.

The purpose of the battery power meter is to give you

a general idea of the remaining burn time. Switching

modes can create an abrupt change in battery voltage

which may cause the indicator to change color. Once

the color turns yellow, the burn time remaining

depends on the typical discharge curve for the type of

batteries you are using. After the light has been turned

off, the battery voltage might temporarily increase,

causing the battery power meter to temporarily display

an artificially higher setting.

When the light is off, the battery power meter will

continue to blink for 24 hours to indicate the current

status of the batteries. After 24 hours with no activity,

the battery power meter will turn off to conserve

battery power. When the light is turned on again, it

will resume functioning.

Low Battery Signaling During Use

In addition to displaying red on the battery power

meter, when there are approximately 20 minutes of

run time remaining, the Apex Pro will blink three

times in rapid succession.

You can then decide to stay at your current light level

or switch to a lower light level, which may cause

battery voltage to rise enough that the battery power

meter transitions back to yellow. When the battery

www.princetontec.com

Operating Instructions

Notice d’utilisation et

d’entretien

Bedienungsanleitung

1 2 4

OFF = press & hold

(1-2 seconds)

Press 1x = High

Press 2x = Med

Press 3x = Low

Hold = Dim

Press 1x = Memory

Press 2x = High

Press 3x = Low

Press 4x = Flash

Hold = Dim

Ultrabright

LEDs

Maxbright

LED

Maxbright

LED

Spotlight

Ultrabright

LEDs

Green > 40 % of total

Yellow ≤ 40 % of total

Red ~ 20 minutes of run time remaining

Color Battery Capacity*

ENGLISH

* The times listed in this table assume you start with fresh batteries and use only one power level.

* Les durées mentionnées dans le présent tableau sont calculées sur la base de l’utilisation de piles neuves et d’un seul

mode d’éclairage.

* Bei den in der folgenden Tabelle aufgeführten Zeiten wird vorausgesetzt, dass Sie neue Batterien und lediglich eine

Leuchtstärke verwenden.

Operation / Fonctionnement / Betrieb

Battery Installation / Mise en place des piles / Einlegen der Batterien

Burn time is the total time that the headlamp produces a minimum of 0.25 lux at 2

meters. 0.25 lux is about the equivalent of a full moon on a clear night. Regulated burn

time is less than overall burn time.

DISTANCE (Meters)

41 12298

Total

11H

HIGH

DISTANCE (Meters)

21 12298

APEX

PRO

LED HEADLAMP

LED STIRNLAMPE

LAMPE FRONTALE LED

power meter returns to red, the light will blink again to

alert you.

Circuitry

The Apex Pro uses a sophisticated circuit to control

the light. Under normal circumstances, the metal

heatsink will sufficiently cool the electronics and

protect the LEDs from damage. Should the internal

temperature of the light get too hot, a backup

temperature protection circuit will activate and

gradually decrease the light output until the

temperature is within the specified limits.

The Apex Pro will automatically turn off after 12 hours

of inactivity. Any button press during the 12 hour

period will reset the auto-off timer.

Never attempt to disassemble the lamp housing. It is

sealed to protect the components from water and

there are no user-serviceable parts inside.

Disassembly will void your warranty!

To keep the heatsink at peak performance, keep the

heatsink and plastic cover free of obstructions (mud

and dirt). Do not remove the heatsink cover—it is

there to protect you from the high temperature of the

heatsink during operation. If the heatsink cover is

damaged or broken under normal use, do not use the

headlamp. See the warranty and return policy for

more information.

Power Consumption

The Apex Pro uses a current-controlled circuit that

maintains constant light output (Ultrabright LEDs) as

long as the batteries have sufficient voltage. Constant

burn time is dependent on the battery type, LEDs, and

light level selected.

The Ultrabright LEDs provide the maximum level

of wide-angle flood light for task work and the

Maxbright will provide a tightly focused spotlight for

distance illumination.

Trouble Shooting

If the Apex Pro fails to light:

•

Check the batteries for proper installation.

•

Inspect the cable for damage.

If the Apex Pro does not seem to change

brightness levels:

• The battery voltage may be too low to switch to

a brighter setting. This condition is normal for a

regulated LED/current-controlled circuit. You are

most likely to experience this issue in the

Maxbright LED mode. Install new batteries and

recheck the modes.

• In extreme heat conditions the internal temperature

of the light may be too hot and the LED

temperature protection circuit may have activated.

Allow the light to cool and try again.

Lifetime Warranty

Due to international regulations, Princeton Tec’s

lifetime warranty can only be offered to customers in

the USA. Princeton Tec offers a 10 year warranty to

our customers outside the USA.

FULL WARRANTY – Princeton Tec warrants this product

to be free from defects in workmanship and materials

under normal use for as long as you own this product.

This warranty covers all of the component parts of the

product except batteries. This warranty does not cover

deterioration due to normal wear or damage due to

misuse, alteration, negligence, accidents, or

unauthorized repair. Princeton Tec will repair or replace

parts which are defective in workmanship or materials.

Your authorized Princeton Tec Dealer and Princeton

Tec are the only facilities authorized to repair the

product. After (3) unsuccessful attempts to repair the

product, you have the right to elect replacement of the

product or a refund of the purchase price less

allowance for use of the product. NO INCIDENTAL OR

CONSEQUENTIAL DAMAGES ARE INCLUDED IN

THIS WARRANTY. (Some states do not allow the

exclusion or limitation of incidental or consequential

damages, so the above limitations or exclusions may

not apply to you.) This warranty gives you specific legal

rights, and you may also have other rights which vary

from state to state.

Princeton Tec reserves the right to change product

specifications without notice.

Return Policy

If your light fails to operate, follow these simple steps:

1. Check batteries. Replace if necessary.

2. To send your light in for repair or replacement, first

contact Princeton Tec customer service on

1-800-257-9080

to request an RMA number.

Please have your light model, date of purchase and

a brief description of the fault you are experiencing.

No warranty repairs will be accepted without an

RMA number.

3. Return the light without batteries to:

Princeton Tec,

PO Box 8057 Trenton NJ 08650

. Postage due and

freight collect items will not be accepted.

4. Upon receipt your light will be processed in about

two weeks. Please allow additional time for return

transportation from NJ.

Princeton Tec

PO Box 8057, Trenton,

NJ 08650

Phone: 609-298-9331

Fax: 609-298-9601

www.princetontec.com

Wide Beam

Regulated

Total

12H

HIGH

Regulated

12H

Total

12H

LOW

Total

10H

FLASH

0418

Total

12H

LOW

Total

10H

MED

Produkt Specifikationer

Mærke:	Princeton Tec
Kategori:	Lommelygte
Model:	Apex Pro
Antal effektniveauer:	120
Vægt:	173 g
Produktfarve:	Sort
Lampe type:	LED
Batteriteknologi:	Lithium
Vandfast:	Ja
Batterilevetid (maks.):	35 t
Batteritype:	CR123
Antal understøttede batterier:	2
Pæreeffekt:	- W
Antal lamper:	5 Lampe( r)
Lommelygte type:	Hovedbånd lommelygte
Lysstråle afstand (maks.):	120 m
Lysstrøm:	200 lm