Qazqa 90502 Manual

Qazqa Lettelse 90502

Læs gratis den danske manual til Qazqa 90502 (4 sider) i kategorien Lettelse. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Qazqa 90502, eller vil du spørge andre brugere om produktet?

Side 1/4
Dark WL III PIR LED Solar
MODEL: 90502
HOW TO DETERMINE WHERE TO MOUNT YOUR SOLAR
PIR SENSOR LIGHT
Please be noted that: DIRECT SUNLIGHT is important for the opera-
on of SOLAR PIR SENSOR LIGHT. The more direct sunlight the solar
cell receives in dayme, the longer the light will operate.
Main Unit:
The main unit contains the lamp (2pcs 0.5W LED), moon sensor and
baery (NI-MH Rechargeable baery, 3.6V, 600mAh). When determi-
ning where to mount this unit, please consider that the moon
sensor with detecon scope of max. 8 meters (in front of the light)
and about 120º (horizontal) at 25 environmental temperature. The
detecon range of the unit may alter with temperature change, the
mounng height and locaon. All Passive Infra-Red detectors are
more sensive in cold and dry weather than warm and humid
weather.
To mount the unit vercally as a security light, aach the unit to a
solid surface as shown in figure . Use the two screws provided in the
package.
Solar Cell:
The solar cell is one of the main power source for the SOLAR PIR
SNESOR LIGHT. It converts the sunlights energy into electricity that
charges the baery in main unit. It requires DIRECT SUNLIGHT onto
the surface of solar cell for as long as possible during the dayme.
Use the two screws provided in the package to mount the solar cell
unit onto a solid surface. Make sure it is fixed into the solid surface.
You can adjust the angle of the solar cell. It should face as much
DIRECT SUNLIGHT as possible during the dayme.
At last route the solar cell’s power cord to the main unit and plug it
into the the side hole for solar cell.
FINAL ADJUSTMENT AND START-UP
Aer you successfully installed your SOLAR PIR SENSOR LIGHT, you
are almost ready for carefree operaon with a few final steps:
Inial 2-days Charge:
On the main unit there is a switch with 2 posions:
OFF ON
ON
Posion for normal operaon
OFF ---
1) Posion for delivery or long periods of non-use
2) Posion for inial 2-day charge before first adjustment and use.
Then, turn the slide switch to OFF posion. The solar cell will charge
the baery without acvang the unit. Leave the switch in this posi-
on for 2 sunny days to ensure that the baery has a full charge for
moon sensor adjustment and normal operaon.
2
HOW TO ADJUST THE MOTION SENSOR
Aer the inial 2-day charge, turn the switch to AUTO posion.
On the moon sensor there are two adjusng knobs: TIME / LUX
1) TIME --- Duraon me: For how long you
wish the light to run aer moon is
detected in the field, the duraon me is
from 10 seconds to 1 minute adjustable.
Note: Once the light is acvated by the PIR
sensor, any subsequent detecon will restart
the med period again from the beginning.
C
Ø6mm
30mm
Ø6x27mm
M4x30mm
6x
6x
87.8
40.00
76.00
42.30
Ø6mm
30mm
42.30
Ø6mm
30mm
7 8
3 4 5
9
12
6
207 mm
106 mm
157 mm
93 mm
185 mm
54 mm


Produkt Specifikationer

Mærke: Qazqa
Kategori: Lettelse
Model: 90502

Har du brug for hjælp?

Hvis du har brug for hjælp til Qazqa 90502 stil et spørgsmål nedenfor, og andre brugere vil svare dig