Rane DA 216 Manual

Rane Blander DA 216

Læs gratis den danske manual til Rane DA 216 (4 sider) i kategorien Blander. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Rane DA 216, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Manual-1

DA 216

DISTRIBUTION AMPLIFIER

OPERATORS MANUAL

DA 216 CONNECTION

When connecting the DA 216 to other components in your

system for the first time, leave the power supply for last. This

gives you a chance to make mistakes and correct them

without damage to your fragile speakers, ears and nerves.

INPUTS

The two Inputs on the DA 216 are balanced. They may

also be used in an unbalanced configuration. Use only

shielded cable for Inputs. This wire should always be two-

conductor plus shield, even for unbalanced operation.

Balanced Inputs should be connected to both the “+” and “–”

terminals. Tie the shield to chassis ground for normal use. In

some cases it may be appropriate to not connect the shield,

QUICK START

This section is provided as a convenience for those in a rush. If you are experienced with this unit or other Rane

products, these few words should help refresh your memory.

Inputs may be microphone or line level. The choice between the two is made by setting the push-buttons on the rear

of the unit near the INPUTS. Follow the silk-screening for proper wiring hookup.

Once INPUTS and OUTPUTS are satisfactorily connected, adjust the Input gain using a combination of the front

panel MASTER LEVELS and the rear panel GAIN switches. Set the level as high as possible without causing the A and

B OVERLOAD indicators to illuminate steadily for high input levels. If 1 x 16 Mono operation is required, use only one

INPUT and activate the MONO switch so the MONO LED illuminates. You may also use both A and B INPUTS for a

stereo signal and the DA 216 will sum the signal before distribution. If 1 x 8 STEREO operation is chosen, select

STEREO. This mode may also be used for two independent mono zones as a 1 x 8 mono distribution amplifier.

Never connect anything except an approved Rane power supply to the thing that looks like a telephone jack on the

rear of the DA 216. This is an AC input and requires special attention if you do not have a power supply exactly like the

one that was originally packed with your unit. See the full explanation of the power supply requirements elsewhere in this

manual.

however when using Phantom Power, this ground connection

is required. For unbalanced wiring use 2 conductor shielded

cable connecting the hot side of the input cable to “+” and the

cold side to the “–”terminal. The shield must connect to the

ground terminal. For best noise rejection, run fully balanced

wiring and connect the shield at both ends to help insure

proper grounding. If a microphone is being connected to the

unit, the shield may be connected to the case of the mic as

well as to the ground terminal on the unit.

OUTPUTS

The DA 216’s OUTPUTS are balanced. The same wiring

conventions as the Inputs apply. For unbalanced OUTPUT

connections, do not tie the unused terminal [i.e. “–”] to GND.

Manual-2

DA 216 FRONT PANEL

1. POWER indicator. When this yellow LED is illuminated, the following information should be correct. If darkness is

present at this location, most or all of the below will be speculation at best.

2. MASTER LEVELS. These screwdriver adjustable controls set the Gain of each Input to be routed to bus A or B for Stereo

operation, or to the odd and even buses for Mono use. The OVERLOAD LEDs illuminate whenever the input section

approaches clipping.

3. MONO switch. This switch is accessed through its hole in the front panel. Any small tool that fits in the hole can actuate the

switch. The associated LED illuminates when in the MONO mode.

4. OUTPUT LEVELS. Each pair of OUTPUT controls sets the individual Channel Output levels. The DA 216 is a combined

stereo or mono unit, depending on the status of the MONO switch. Stereo outputs are labeled in white, mono outputs are

labeled in gray.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Blander
Model:	DA 216

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane DA 216 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blander Rane Manualer

24 Juni 2025

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

Blander Manualer

Nyeste Blander Manualer

Ibiza Sound MX401 Manual

14 September 2025

Mackie 1642VLZ4 Manual

14 September 2025

Mackie ProFX10v3+ Manual

14 September 2025

Mackie Master Fader Control App Manual

14 September 2025

Mackie DL32S Manual

14 September 2025

Mackie 1402VLZ4 Manual

14 September 2025

Mackie Onyx 12 Manual

14 September 2025

Mackie ProFX12v3 Manual

14 September 2025

Mackie 1604VLZ4 Manual

14 September 2025

Mackie Pro FX30 v3 Manual

14 September 2025