Rane MA 3 Manual

Rane Blander MA 3

Læs gratis den danske manual til Rane MA 3 (5 sider) i kategorien Blander. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Rane MA 3, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

Manual-1

OPERATORS MANUAL MA 3

MULTICHANNEL AMPLIFIER

QUICK START

Sure, you say, “it's just a three channel amp, I'm in a hurry and I don't need to read the manual.” But at least read this

little section so you really know what to expect, and your installation can go even faster.

Be sure the Amplifier is off before making any connections. Euroblocks make Amplifier connection easy. They are just

like “snap on” terminal blocks. The balanced Input blocks are three-terminal female connectors. The Output blocks are two-

terminal female connectors.

Driving the MA 3 from a balanced source is recommended. If you must drive the MA 3 Input with an unbalanced

source, we recommend using a cable that has two conductors plus a shield, and be sure to keep cable lengths as short as

possible (under 10 feet). See Rane Note 110, “Sound System Interconnection” (contained in this booklet).

Nominal speaker loads should be no lower than 4 ohms per Output. If you are running series or parallel combinations,

be sure and check your total load impedance. For constant-voltage distribution, consider using the optional TF 407 (40 W /

70.7 V) or TF 410 (40 W / 100 V) transformer. Transformers may be installed inside the MA 3 on any number of Output

Channels required. If you intend to use constant-voltage distribution transformers, you may want to read RaneNote 136

“Constant-Voltage Audio Distribution Systems” (contained in this booklet).

Once Input and Output connections are completed, be sure all rear panel LEVEL controls are all the way counterclock-

wise. Now flip the POWER switch on. After a couple of seconds, slowly turn up each Channels’ LEVEL control to the

desired gain. Maximum yields the most effective dynamic range control for the built-in Limiter). If all is well, you will hear

something pleasant. If not, re-check connections, put on a better CD, and read more of the manual.

WEAR PARTS: This product contains no wear parts.

Manual-2

FRONT PANEL DESCRIPTION

 Heat tunnel exhaust vents are located on the left of the unit. Large aperture vent slots are used for low noise. Air is taken

in at the back of the unit and exhausts out the front. When installed in a rack, make sure there is ample room for air to exit.

The sealed heat tunnel design does not require the use of an air filter.

 OUTPUT HEADROOM meters indicate the amount of remaining headroom (how much more signal can be applied before

Limiting occurs).

0 dB OUTPUT HEADROOM remaining is indicated by a red indicator. When lit, any additional signal causes the Limiter to

operate. It is possible to “compress” the signal as much as 20 dB with very little effect on sound quality. This gives the

MA 3 the overload characteristics of a much larger amplifier, without the use of external compressors. The MA 3 was

designed to be driven hard (heavily compressed signal) so it is not necessary to buy extra power to obtain the headroom

required to prevent overload.

3 dB OUTPUT HEADROOM remaining is indicated by a yellow indicator. When lit, 3 dB of additional signal may be

applied before Limiting.

6 dB OUTPUT HEADROOM remaining is indicated by a green indicator. When lit, 6 dB of additional signal may be

applied before Limiting.

12 dB OUTPUT HEADROOM remaining is indicated by a green indicator. When lit, 12 dB of additional signal may be

applied before Limiting.

  PWR: This yellow indicator lights when power is applied to the unit. See below.

 POWER switch: This control obediently turns the MA 3 on and off every time you poke it with your finger. Poking the top

half of the switch turns the unit on when it is off. Poking the bottom portion of the switch turns the unit off when it it on. All

three Channels have turn-on and turn-off muting to reduce switching transients.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Blander
Model:	MA 3

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane MA 3 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blander Rane Manualer

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

20 Juni 2025

20 Juni 2025

Blander Manualer

Nyeste Blander Manualer

Glemm MMX 54ZM Manual

21 Juni 2025

Roland M-5000 Manual

20 Juni 2025

DNA HLC 10 MK2 Manual

17 Juni 2025

16 Juni 2025

16 Juni 2025

16 Juni 2025

15 Juni 2025

13 Juni 2025

13 Juni 2025

NutriBullet Ultra Plus+ Manual

12 Juni 2025