Rane NM 48 Manual

Rane Blander NM 48

Læs gratis den danske manual til Rane NM 48 (16 sider) i kategorien Blander. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Rane NM 48, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/16

Manual-1

OPERATORS MANUAL NM 48

NETWORK PREAMPLIFIER

WEAR PARTS: This product contains no wear parts.

CobraNet is a trademark of Peak Audio, Inc.

Quick Start

Ok, if you’ve read the NM 84 manual you might get a sense of déjà vu when you read this one. Maybe not quite as

strong as if you were watching another Adam Sandler movie, but déjà vu just the same. The reason for the similarity is that

the complicated stuff (network design) is such a large part of the installation. This is basically the same for both units.

First, design the network – a dedicated network for CobraNet audio is recommended, but not required when using

switch-based networks. The NM 48’s CobraNet technology utilizes standard 100Base-T Ethernet hardware. For CobraNet

and network design assistance and a list of other CobraNet licensed and tested devices, visit www.peakaudio.com/cobranet.

Rear Panel. Connect up to 4 line-level, analog audio inputs to the XLR INPUTS. Each of the eight OUTPUTS can

independently receive any of the 4 Local Input audio channels or any single Audio Channel from one of four CobraNet

Bundles from 1 through 999, plus off/none. Connect the network cable to the 100Base-T RJ-45 jack. The RS-232 jack

transports RS-232 data over the network to other NM, RS-232 device ports. The RS-232 port does not provide control of the

NM 48. Connect contact closures to the MEMORY RECALL PORT (MRP) to recall Memories on this device or any

other NM device(s) connected on the same network. Connect the locking 5-pin DIN jack on the enclosed RS 3 power supply

to the NM 48 POWER connector. The RS 3 power supply does indeed connect earth ground – the 3

pin of the AC line

cord – to the NM 48 chassis metal. Depressing the recessed FP LOCK (Front Panel Lock) button at this point disallows

further front panel setup, so only press this button in once you’re completely done setting up the NM 48.

Front Panel. There are 14 LCD screens allowing access to all NM 48 parameters. The first eight LCD screens set up the

Outputs; Output 1: through Output 8:, respectively. Each of the 8 Outputs can receive any of the local Input channels or

any CobraNet Audio Channel from one of four Bundles. Use the Copy field to copy and paste between the various screens.

The next screen allows the Inputs; Input 1: through Input 4:, to be turned On or Muted.

The NetRx: LCD edit page sets up the four possible CobraNet Bundles (Bndl) that the NM 48 can receive from the

network; use NetRx’s Bndl A, Bndl B, Bndl C and Bndl D fields to set the received Bundle(s).

The four NM 48 Input audio channels can be transmitted on up to 4 different CobraNet Bundles. Each of the 4 Bundles

contains all four Input audio channels and are transmitted in 24-bit resolution. CobraNet designates each of the four, Audio

Channels (i.e., AudCh 1 through AudCh 4, respectively). The Network Transmit LCD screen (NetTx) allows selection of

the four Bundles to transmit, each of which are independently assignable to one of the 999 Bundles using the four NetTx

fields; Bndl A, Bndl B, Bndl C and Bndl D.

The Mem (Memory) LCD screen allows 16 unique NM 48 setups to be stored and recalled in the 16 memory locations.

Additionally, the NM 48’s MRP status can be transmitted over the network for other NM devices to “listen to.” Set the

MRP Tx (MRP Transmit) and MRP Rx (MRP Receive) fields for any or none of the 16 available MRP channels. The Serial:

LCD screen sets the RS-232 serial port’s Baud rate and the 232 Tx and 232 Rx fields which set the transmit and receive

RS-232 channels. There are 255 serial data channels available for transport over the network.

The final Config: LCD screen displays the current/editable IP Address and the editable Name of the NM 48 device (8

characters max). Set the IP address to 0.0.0.0 (the default) to enable CobraNet’s Discovery Utility (Disco) to dynamically

assign the IP address. Peak Audio’s Discovery Utility allows you to plug into a CobraNet network with a standard Ethernet

computer card (NIC) and discover all of the CobraNet devices on the network. The Disco software utility has the ability to

dynamically assign IP addresses as well as update CobraNet firmware on the discovered CobraNet devices. Disco is

available from www.peakaudio.com/cobranet as well as many music retailers which carry The Village People, KC & the

Sunshine Band, Wild Cherry and the like.

Do yourself a favor and at least read the Important Big Picture Concepts section found elsewhere in this manual.

Reviewing the Network Examples provides insight into a logical order for design work and would also be a way to avoid

initial confusion.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Blander
Model:	NM 48

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane NM 48 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blander Rane Manualer

24 Juni 2025

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

Blander Manualer

Nyeste Blander Manualer

Audac M2 Manual

16 Oktober 2025

Proel ATMP480Z6XL Manual

14 Oktober 2025

TOA M-124FX-EB Manual

10 Oktober 2025

Audiophony MYA8C Manual

6 Oktober 2025

Audiophony Digital-3 Manual

6 Oktober 2025

Audiophony MYA5D Manual

5 Oktober 2025

Proel MQ16USB Manual

4 Oktober 2025

Rolls Mini-Mix VI MX28 Manual

3 Oktober 2025

Rolls RM65B Manual

3 Oktober 2025

Rolls PM60 Manual

3 Oktober 2025